CYCMOTOR Topology DS103 TFT and Remote BMZ Display User Guide

June 9, 2024
CYCMOTOR

CYCMOTOR Topology DS103 TFT and Remote BMZ Display User Guide
CYCMOTOR Topology DS103 TFT and Remote BMZ Display

Product Details

Product Name
Intellegent LCD display, model : DS103
Firmware: CYCMotor Ltd specic rmware

Features

  • Simple and lightweight, separate installation bracket design
  • High brightness, high contrast 3.5 coloured TFT screen
  • Clock function (clock is on when the display shutdown)
  • Excellent outdoor design with IP65 level waterproof
  • Micro USB serial communication port, convenient maintenance services.

Dimensions & Materials

Materials
Product shell – ABS + PC plastic
Transparent window – Tempered glass

Dimensions
L 110mm x W 68.2mm x H 68mm

Dimensions
Dimensions

Electrical Specications

  • Power supply:DC 24V/36V/48V/ 52V
  • Rated current:30ma/36V
  • Shutdown leakage current:<1uA
  • Screen specication: 3.5” colored TFT(480*320pixels)
  • Communication method:UART (default)
  • Operating temperature:-20°C ~ 60°C
  • Storage temperature:-30°C ~ 80°C
  • Waterproof level:IP65

Quick Start Guide

After unboxing and installing your CYC motor system, there are two main things you need to set up.

  1. Change your Battery No. settings according to your rated voltage. Within 15 seconds of turning on your display, long press the MENU button to enter the settings functions. Press UP/DOWN to navigate the settings page & MENU to select.
    INSTRUCTION

  2. Change your Wheel settings according to your bike’s wheel size.
    INSTRUCTION

  3. Now, you can set things up like your temperature and speed unit as well as your brightness level. Otherwise you’re good to go!

Functionalities

Power On/ Off
Press and hold the POWER button for 3 seconds to turn the display on/ o.

Navigation
The MENU button is used to go into your main settings page & your clear data page. It is also used to enter and select a setting or function.

  1. POWER
  2. MENU
  3. UP
  4. DOWN

Switch Dashboard
Switch the main dashboard to display dierent information by pressing the MENU button.

Switch Dashboard

Assist Level Operating
Press the UP/ DOWN button to change the assist level between level 1, 2, and 3. Note that “OFF” means no motor assistance will be given.

Assist Level Operating

Dark & Light Themed Dashboard
Long press the UP button to switch between light and dark themed dashboard.

Dark & Light Themed Dashboard

Walk Assist
Hold in the DOWN button to activate walk assist. Note that it takes 3 seconds to activate & will deactivate immediately when the button is released.

Walk Assist

Settings
Long press the MENU button within 15 seconds of switching on the display to enter the “Settings” page. Note that once the system has been activated for longer than 15 seconds, you will need to restart the motor system to enter the settings menu.

Settings

Clean Trip Data
Wait 15 seconds after starting up the motor system to enter the “Clean Data” menu. Long press the MENU button to clear the previous trip data. Please note that the trip data does not automatically clear once you restart the motor system. This is a manual process.

Clean Trip Data

Error Codes
In certain circumstances, an error code may appear on your display. Contact technical_support@cycmotor.com

Error Codes

Installation

  1. Determine if you need to select the corresponding mounting clamp and rubber clip ring according to the diameter of your handlebar (Applicable handlebar specications:Φ22.2 ; Φ25.4 ; Φ31.8).
  2. Open the display lock clamp and insert the rubber clip (if applicable) into the correct position of the lock clamp.
  3. Set the rubber ring in the bracket (if applicable) then assemble on the middle of the handlebar. You can adjust the angle of the display to make the display screen more visible when riding. After xing the angle, tighten the screws. Tightening torque is 1N.m.
  4. Open the lock ring of the switch and set it in the appropriate position on the left side of the handlebar. Adjust the angle and position of the switch as needed in order to ensure that you can operate the switch easily.
  5. Fix and tighten the handlebar xing screw with M3Hex wrench (locking torque is 0.8Nm).
  6. Connect the display connector to the controller connector according to the label.

Note: Damage caused by excessive torque is not covered by warranty.

Compatibility
The clamps are suitable for 3x dierent handlebar sizes: 31.8mm, 25.4mm, and 22.2mm.

Compatibility

Pin Layout

Male 5-Pin Connector
INSTRUCTION

  1. Red wire: Anode (36V to 72V)
  2. Black wire: GND
  3. Yellow wire: TxD (display -> controller)
  4. Green wire: RxD (controller -> display)
  5. Blue wire: Power ord to the controller

Cerification
CE / IP65 (waterproof) / ROHS.
Be sure to contact techinical_support@cycmotor.com if further assitance is needed. Thank you!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals