meister MHG2000-2 Hot Air Blower Instruction Manual
- June 4, 2024
- meister
Table of Contents
- Operating instructions & safety hints
- Scope of delivery
- Technical information
- Components
- Correct use
- General safety instructions for handling power tools
- Safety instructions relating specifically to the equipment
- Installation and setting
- Operation
- Mode of operation
- Maintenance and environmental protection
- Service instructions
- Documents / Resources
MHG2000-2 Hot Air Blower
Instruction Manual
Nr. WU5460520
5460520-Heissluftgeblaese-man.indd 1
Service
Conmetall Meister GmbH
Kundenservice
Oberkamper Str. 39 · Warenannahme Tor 3
42349 Wuppertal
Tel.: 0202 / 24 75 04 30
0202 / 24 75 04 31
0202 / 24 75 04 32
Fax: 0202 / 6 98 05 88
E-Mail: meister-service@conmetallmeister.de
Diese Betriebsanleitung kann im PDF-Format von unserer Internetseite
www.conmetallmeister.de heruntergeladen
werden.
|
|
Operating instructions & safety hints
WARNING! To reduce the risk of injury, please read the operating instructi carefully before using the device, and then store it with the machine! When passing the device on to another user, these operating inst ructions must also be included!
Scope of delivery
- Hot air gun
- 4 attachment nozzles and 1 scraper
- Operating instructions
- Guarantee certificate
Technical information
Technical data
Power supply 230 V~/50 Hz
Power consumption Pmax. = 2000 W
Power consumption/ I: PN 1000 W/
Temperature/ 350 °C/300 l/min
Volume of air II: PN 2000 W/ 550 °C/500 l/min
Cable 300 cm
Weight 0.65 kg
Components
- Air inlet
- Unit stand
- On/Off switch
- Handle protection
- Accessory mount
- Hot air outlet
- Attachment nozzles and paint scraper
Correct use
- Removing paint and varnish.
- Removing stickers.
- Loosening rusty and too tight nuts and metal screws.
- Thawing frozen pipes, door locks, padlocks, etc.
- Highlight natural grains in wood surfaces before varnishing or painting. Desacaling wood panelling.
- Quick-drying paint and varnish. This is particularly useful where color harmonization is required through several coats. Drying test coats. Work carefully and from a greater distance.
- Removing old putty from window panes.
- Drying wet and damp objects and grounds before reworking.
- Shrinking packaging foil.
- Waxing and dewaxing skis.
- Shrinking polyvinyl wire connections.
- Stripping floor coverings.
- Shaping plastic.
All other applications are expressly ruled out.
The machine is intended only for use in the household.
General safety instructions for handling power tools
WARNING! Read all safety warn ings and all instructions. Failure to
follow the warnings and instructions may result in electric shock, fire,
and/or serious injury. Save all warnings and instructions for future
reference. The term “power tool” in the warnings refers to your mains operated
(corded) power tool or battery-operated (cordless) ower
tool. This device may be used by children aged 8 and above as well as by
people with reduced physical, sensory or mental capacities or a lack of
experience and knowledge as long as they are supervised or have been taught to
use the device safely and they are aware of the risks involved. Children may
not play with the device. Cleaning and user maintenance may not be carried out
by children without supervision.
1 Work area
a Keep work area clean and well lit.
Cluttered and dark areas invite accidents.
b, Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
that may ignite dust or fumes.
c Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2 Electrical Safety
a Power tool plug must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce the risk of electric shock.
b Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges, and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d, Do not abuse the cord. Never use the cord for carrying, pulling, or
unplugging the power tool. Keep cord away from heat, oil, sharp edges, or
moving parts. Damaged or entangled cords increase the risk of electric
shock.
e When operating a power tool out doors, use an extension cord suita be
for outdoor use. The use of a cord suitable for outdoor use reduces the risk
of electric shock.
f If it is not possible to avoid using the electrical tool in a damp envi
ronment, use a residual current cir cuitbreaker. The use of a residual
current circuit-breaker reduces the risk of an electrical shock.
3 Personal safety
a Stay alert, watch what you are doing, and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the
influence of drugs, alco hol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b Use personal protective equipment. Always wear eye protection.
Protective equipment such as dust masks, non-skid safety shoes, hard hats, or
hearing protection used for appropriate conditions will reduce personal
injuries.
c Prevent unintentional starting. Ensure the switch is in the offposi
tion before connecting to a power source and/or battery pack, picking up or
carrying the tool. Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites accidents.
d Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing, and gloves away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.
g If devices are provided for the connection of dust extraction and col
lection facilities, ensure these are connected and properly used. The use of
these devices can reduce dust-related hazards.
4 Power tool use and care
a Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate at which it was designed.
b Do not use the power tool if the switch does not turn on and off. Any
power tool that cannot be controlled with the switch is dangerous and must be
repaired.
c Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk
of starting the power tool accidentally.
d Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to oper ate the
power tool. Power tools are dangerous in the hands of untrained users.
e Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may affect the power tool’s
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g Use the power tool, accessories and tool bits, etc. in accordance with
these instructions, taking into account the working conditions and the work to
be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation.
5 Service
a Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b To avoid hazards, damaged power leads must be replaced by the
manufacturer or his customer service representative.
Safety instructions relating specifically to the equipment
-
When carrying out work in which dust is generated, wear a face mask and safety goggles – do not smoke and avoid naked flames.
-
Make sure that the switch is in the 0 positions before putting the plug in the socket.
-
The nozzle gets very hot. Always wear gloves and safety glasses.
-
Never use the hot-air gun as a hair drier.
-
Never direct the hot-air low at people or animals.
-
Do not use it in an atmosphere prone to explosion.
-
After use, set down the device on the stand and allow it to cool before putting it away.
-
Do not use the hot-air gun near easily flammable materials or gases.
-
Never obstruct the hot-air low.
-
To cool the hot-air gun, always place it in an upright position (fig. 2) or hang it up by the bracket provided.
-
Never use the hot-air gun in a wet environment or in areas with a high degree of humidity (e.g. bathrooms, saunas, etc.).
-
When the hot-air gun is being used in a standing position, make sure that it stands on a firm, dust-free surface.
-
Vapors can be generated when hot air is used. Always make sure the working area is well ventilated.
The symbols on the housing have the following meanings:
Important! Observe the operating instructions!
Housing is double insulated.
CE mark
(conformity with European safety standards)
Do not dispose of with the household waste!
Voluntary „geprüfte Sicherheit“ seal of quality (tested safety)
BJ: Year of construction
SN: Serial number
SN: XXXXX The first two underlined numbers give the month of manufacture.
Installation and setting
Mounting the attachment nozzles
A different type of attachment nozzle (7) may be used according to the work
you are carrying out. The attachment nozzles are clamped to the accessory
mount (5). In order to ensure a firm seat, the rear section of the nozzle may
need to be squeezed with a pair of pliers.
CAUTION! Attachment nozzles that are not securely mounted may become
loose when working and cause burns!
Operation
Switching on
Set the switch (3) to the I setting. Within a minute the hot air gun will
reach an operating temperature of 350 °C.
Set the switch to the II setting. Within a minute the hot air gun will reach
an operating temperature of 550 °C.
Switching off
Switch the unit to the 0 settings and leave it on the stand (2) to cool down
(Figure 2).
NOTE: If the hot air gun is being operated with an attachment nozzle,
switch it off after around 3 minutes and allow it to cool down on the stand
for around 3 minutes to
ensure that the unit does not over heat!
The integrated stand (2) means that the unit can be stood up vertically on any
smooth surface (Figure 3). This leaves both hands free to work.
Mode of operation
CAUTION! Because of the expected smoke generated when using the unit,
you should always wear suitable breathing protection!
CAUTION! Never direct the hot air gun onto the power cable! The cable
should not come into contact with the hot nozzle or hot tool as this may melt
the insulation of the cable. This may cause electrical shock!
Carefully heat workpieces from a greater distance to start with. If necessary,
reduce the gap.
Removing paint and varnish (Figure 4)
NOTE: The hot air gun is suitable for removing both oil and latex-based
paints! It cannot be used to remove glazes or primers applied to impregnate
wood.
CAUTION! Paint vapors are haz arduous! You should also ensure
sufficient ventilation when working indoors. Remove any paint on the nozzle
immediately! Risk of fire, if the paint is overheated!
- Always do a test on a small section of paints before you tackle larger surfaces.
- Do not use any chemical strippers in conjunction with the hot air gun.
- Switch the hot air gun on. Direct the nozzle onto the paint whilst maintaining a gap of 8-10cm and wait until it starts to blister. Use a scraper or knife to remove the paint from the surface. Work in even sweeps in the direction of the blisters.
- Heat the section in front of the scraper or knife by moving the gun backward and forwards gently.
- The edge of the scraper or knife must be wiped frequently to ensure that it is clean and sharp.
- On surfaces with contours, the paint must irst be softened and then removed with a wire brush.
- All surfaces that are not to be heated should be covered with non-combustible materials. Never direct the water jet onto a window pane or other glass surfaces.
Area of application for attachment nozzles
The attachment nozzles for specialist tasks are fitted to the air outlet of
the hot air gun when required.
Flat nozzle (a)
Ideal for removing paint (Figure 4). Also suitable for defrosting frozen water
pipes (Figure 5).
CAUTION! Water pipes and gas pipes are very similar to look at! Gas
pipes may not be heated!
Deletion nozzle (b)
Protects neighboring surfaces that should not be heated or are sensitive to
heat, for example, window panes (Figure 6).
Reflector nozzle (c)
Used to shape plastics, e.g. pipes, and to shrink cables (Figure 7).
Spot nozzle (d)
For accurate work and for soft-soldering (Figure 8).
Maintenance and environmental protection
Ensure that the air inlet and outlet opening are always clean and free from dirt. Clean the gun with a damp cloth. Do not use turpentine, paint stripper, petrol, or other similar substances to clean the unit.
CAUTION! Unplug from the power source before cleaning!
CAUTION! Electrical and battery-operated units that no longer work
should not be disposed of in the household waste! They are to be col elected
separately, in accordance with the 2012/19/EU directive for the disposal of
electrical and electronic waste and sent for proper and environmentally
friendly recycling.
Please discard power tools no longer usable at a local collection point.
Collection and disposal of packaging materials separately by types comply ing
with local rules and regulations. For details, please contact your municipal
authority concerned.
Service instructions
- Store the machine, operating instructions, and where necessary the accessories in the original packaging. In this way, you will always have all the information and parts ready to hand.
- Meister devices are to a large extent maintenance-free, a damp cloth being sufficient to clean the casing. Do not drop electrical machines in water. Please note additional hints given in the operating instructions.
- Meister devices are subject to stringent quality control. If however, a functional fault should occur, send the device to our servicing address. The repairs will be carried out in a short time.
- A brief description of the defect speeds up the fault tracing and repair time. If within the guarantee period, please enclose the guarantee document and the proof of purchase.
- In so far as a repair under guarantee is not concerned, we will charge the repair costs to your account.
PLEASE NOTE! Opening of the device invalidates the guarantee claim.
IMPORTANT! We point out expressly that in accordance with the Product
Liability Act we do not take responsibility for any dam age caused by our
appliances, in so much that said damage is caused by improper repair, or
original parts or parts released by us not being used when parts are changed,
or repairs not being conducted by metal
Meister GmbH Customer Service or an authorized specialist! The same applies
analogously to the accesso ries used.
- Pack the device well or use the original packaging in order to avoid transit damage.
- Even after the expiry of the guarantee period, we would like to help you and carry out any repairs at a favorable price.
EU declaration of conformity
We declare with sole responsibility, that the product listed below …
HotAirGun
MHG20002 Nr. WU5460520 BJ:2022 · SN:09001
… meets all of the requirements of the listed directives.
2011/65/EU (RoHS)
2014/30/EU (EMVRL)
2014/35/EU (NRL)
Ingo Heimann (M.Sc.)
Technische Leitung/Produktentwicklung
Conmetall Meister GmbH · Oberkamper Straße 39 · 42349 Wuppertal
Angewandte harmonisierte Normen:EN 603351:2012/A2:2019
Aplikované súvisiace normy:EN 60335245/A2:2012
Normes harmonisées utilisées:EN 62233:2008
Applied, harmonized standarts:EN 550141:2017/A11:2020
Toegepaste, geharmoniseerde normen:EN 550142:2015
Wykorzystane normy sharmonizowane:EN IEC 61000322019
Uygulanan normlar:EN 6100033:2013/A1:2019/EN IEC 63000:2018
Person authorised to store technical documents.
© Copyright
Nachdruck oder Vervielfältigung – auch
auszugs weise – nur mit Genehmigung der
Conmetall Meister GmbH
Oberkamper Str. 39
42349 Wuppertal
Germany
Documents / Resources
|
meister MHG2000-2 Hot Air
Blower
[pdf] Instruction Manual
MHG2000-2, Hot Air Blower, MHG2000-2 Hot Air Blower
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>