MEEC TOOLS 019148 Soldering Iron Instruction Manual

MEEC TOOLS 019148 Soldering Iron

SAFETY INSTRUCTIONS

Follow all the safety instructions and operating instructions.

• All persons who use or service the product must have read these instructions and be aware of the potential risks associated with the product.
• This product can be used by children from 8 years and upwards and by persons with physical, sensorial or mental disabilities, or persons who lack experience or knowledge, if they are supervised or receive instructions concerning the safe use of the product and understand the risks involved with its use. Do not allow children to play with the product. Do not allow children to clean or maintain the product without supervision.
• The soldering pen is intended for melting and applying solder on different surfaces, for both large and small repairs.
• Do not use the product when other persons, especially children, or pets, are in the vicinity.
• Always follow local regulations for safety at the workplace and prevention of accidents.
• Never modify the product in any way. The manufacturer cannot be held liable for any personal injury and/or material damage resulting from such modifications.
• Put the product on its stand when not in use.
• The product must only be connected to an earthed power point 230 V ~ 50 Hz.
• Wear safety glasses.
• Only use the product in a well ventilated area.
• Keep the work area clean, well lit and ventilated.
• Never leave the product unattended when plugged in.
• Only use the product on a fireproof underlay.
• Never touch the soldering tip when the plug is plugged in.
• Even if the product is used in accordance with the instructions it is impossible to rule out all risk factors. The following are potential risks associated with the type and design of the product.
  • Risk of damage to lungs if an effective breathing mask is not worn.
  • Risk of eye damage if safety glasses are not used.
  • Risk of burn injury from contact with hot surface.

ELECTRICAL SAFETY

• The plug on the power tool must match the power point. Never modify the plug in any way. Never use an adapter with earthed power tools. Unmodified plugs and matching power points reduce the risk of electric shock.
• Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators. There is an increased risk of electric shock if your body is earthed.
• Do not expose power tools to rain or moisture. There is a greater risk of electric shock if water gets into a power tool.
• Be careful with the power cord. Never use the power cord to carry or pull the tool, or to pull out the plug from the power point. Keep the power cord away from heat, oil, sharp edges and moving parts. Damaged or tangled power cords increase the risk of electric shock.

PERSONAL SAFETY

• Stay alert. Pay attention to what you are doing, and use your common sense when working with power tools. Never use power tools if you are tired or under the influence of drugs, alcohol or medication. A moment of inattention when using a power tool can result in serious personal injury.
• Use personal safety equipment. Wear safety glasses.
• Avoid accidental starting. Check that the power switch is in the OFF position before plugging in the power cord and/or the battery, or lifting/carrying the tool. Carrying a power tool with your finger on the switch, or connecting a tool to the mains supply when the switch is in the ON position, increases the risk of accidents and injuries.
• Remove adjuster keys/spanners etc. before starting the tool.
• Do not overreach. Always maintain a firm footing and good balance. This will ensure you have better control over the tool in unexpected situations.

SYMBOLS

• Read the instructions.
• Approved in accordance with the relevant directives.
• Recycle discarded product in accordance with local regulations.
• Wear safety glasses.
• Safety class II.
• For indoor use only.

TECHNICAL DATA

• Rated voltage 230 V ~ 50 Hz
• Output150 W
• Temperature range 400-500°C
• Cord length 1.2 m

DESCRIPTION

Soldering iron for both large and small repairs. The soldering tip is angled and replaceable.

1. Handle
2. Status light heating
3. Soldering tip
   **FIG. 1

**

USE

1. Check that the mains voltage corresponds to the rated voltage on the type plate.
2. Plug the plug into a suitable power point.
3. Remove any oxide and all contaminants from the workpiece.
4. Allow the soldering tip to warm up.
5. Tin the soldering tip.
6. Put the soldering tip on the workpiece.
7. Put solder in the contact point between the soldering tip and the workpiece.
8. Allow the solder to melt and spread.
9. Lift the soldering tip and the soldering wire off the workpiece at the same time.

WARNING!

• Put the product on its stand when not in use.
• Wear safety glasses.
• Only use the product in a well ventilated area.

References

• Jula – products for home and garden

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>