GERMAN FXS3 Remote Control Kit User Manual

GERMAN FXS3 Remote Control Kit

Safety Instructions

• This remote control may only be installed and started up for the first time by an authorized specialized company. Responsibility for compli-ance with the applicable standards and installation regulations rests entirely on the company installing the appliance. We cannot accept any liability for damage and losses due to noncompliance with these instructions. Read this manual completely before starting up the remote control.
• The handling of the appliance and the remote control are equitable. The last set temperature will be used by the instantaneous water heater. Make sure not to set a high temperature, inadvertently. We recommend to activate the temperature limit function (see manual of the instantaneous water heater).
• Flat batteries can leak and damage the remote control. Hence, re-place flat batteries right away as soon as battery symbol lights up in the display or the remote control does not response after keystroke.
• When the remote control is not to be used in the long term, remove the batteries.
• Do not expose the remote control to moisture.
• Keep the remote control and wall bracket away from credit cards or other cards with magnetic strips. The built in magnets can damage the card’s magnetic strip.
• This appliance can be used by children aged 3 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or ins truction concerning use of the appliance in a safe way and under-stand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be performed by children without supervision.

Description Of Appliance

• The FXS 3 remote control set consists of the FX 3 remote control and the FXE 3 radio adapter. The FX 3 remote control allows a convenient operation of the instantaneous water heater even if the heater is installed under a sink or in a secondary room. An energy-efficient and adequate choice of the water temperature is furthermore possible under these conditions with the FX 3 remote control.
• The communication between the remote control and the instantaneous water heater is via Bluetooth®. Due to this technology the data transfer is secured even under difficult installation conditions.
• To connect the remote control to an instantaneous water heater other than DSN, the provided Bluetooth adapter must be installed.

Dimensions

Technical Specification

NOTE: Do not use rechargeable batteries.

• All information in this manual is for reference only. If there are any errors or omissions, the specifications produced by the factory shall prevail. Specification is subjected to change without prior notice.
• If there is any inconsistency or ambiguity between the English version and the Chinese version of this manual, the English version shall prevail.
• Refer to www.germanpool.com for the most up-to-date version of the Operating Instructions.

Installation

Mounting the Wall Bracket
NOTE: Before attaching the wall bracket to the wall, ensure that the remote control has radio contact to the instantaneous water heater from its designated position.

• The wall bracket of the remote control can either be attached securely with the included adhesive tape, after stripping off the protection film (as shown in fig. 1) on a plain surface (e.g. a tile) or with suitable dowels (Ø 4 mm) and screws (as shown in fig. 2).
• When using the adhesive tape it is not possible to adjust the position afterwards because of the strong adherence of the glue. Therefore, pay attention to horizontal alignment when attaching it.
• The remote control is magnetically retained at the wall bracket.

Mounting the Bluetooth Adapter

Attention

• Before assembling the Bluetooth adapter, disconnect the instantaneous water heater from the mains supply!
• The adapter antenna is very fragile! Please be careful when mounting it.

Step 1: Remove the electronics cover
Step 2: Release the PCB from the catch and lift it slightly
Step 3: Connect the Bluetooth adapter. (Pay attention to the proper position of the connector!)
Step 4: Snap the PCB back into place
Step 5: Attach the electronics cover. Adaptor installation completed.

Scan QR code to watch adaptor installation video

Initial Operation

1. Make sure that the power supply to the instantaneous water heater is switched on (fuse) and that the display (if available) of the instantaneous water heater shows the latest set value.
2. After inserting the batteries, the remote control briefly displays all symbols. Then “8A” and the percentage of battery charge are displayed and the display changes to the PIN entry “P1” .
3. Enter the first four digits of the Bluetooth PIN and press to confirm. The PIN can be found on the type plate of your instantaneous water heater (the set of numbers after BLE).
4. Press plus and mins to change the current digit. Press 1 to proceed to the next digit. After entering “P4” and pressing 1 , the PIN is applied.
5. After entering the pin, the remote control automatically connects to the instantaneous water heater, “D1” appears during the registration procedure. If there are several instantaneous water heaters within range, they may be checked first (display “D2…D3…” ). This can take up to one minute. To avoid this, hold the radio remote control directly in front of the instantaneous water heater to be registered.
6. Once connected, the display of the remote control switches to the set point value display.

Note

• If registration is unsuccessful, the display shows “E1”. The remote control quits the registration process and switches to standby mode. Repeat the registration process by pressing any button on the remote control.
• If the registration is still unsuccessful after a number of trials, check the pinning position of the radio adapter.
• With no remote control registered or without working Bluetooth connection, the instantaneous water heater heats to the prior selected set temperature.
• After replacing the batteries, a new registration is not required.
• After a power failure of the instantaneous water heater, a new registration is not required.
• Automatic re-registration after a battery change or power failure can take up to one minute
• If the instantaneous water heater makes noises (beeping, buzzing) after switching on, the software is in the process of updating.

Re-registration of the Remote Control
To connect the remote control to another instantaneous water heater, press and hold all four buttons on the remote control for at least 5 seconds. This starts the initial operation mode. Repeat steps 3-6 to connect to the new water heater.

Handling

The remote control is equipped with the following functions:

1. Temperature Buttons
   You can set the required temperature gradually to a lower or higher value using the two buttons and .
   Note: If the temperature display is set to “–” with button, the instantaneous water heater switches off the heating function.

2. Programme Buttons
   The two programme buttons 1 and allow 2 to quickly select the preset temperature without the need to press the plus and mins buttons several times.
   The factory setting for programme is 35 °C and for programme is 48 °C. You can assign your own settings for the programme buttons:

   • Select the desired temperature with plus and mins
   • To save the current temperature, press the programme button or for about two seconds.

3. Restart and Battery Capacity
   Press and hold plus and mins for approx. 5 seconds to restart the remote control. All symbols are displayed briefly, followed by the battery display.

4. Info menu
   Press and hold the programme keys 1 and 2 for about 5 seconds to open the info menu. Press 1 or 2 briefly to navigate back and forth in the displays. Long presses on 1 and 2 exit the menu again.

Menu displays

Displayed Information

The representation corresponds to the temperature display of the instantaneous water heater display after a keystroke on the remote control. The description of the function can be found in the manual of the instantaneous water heater.

Radio Communication
This radio symbol is displayed on the remote control, if a button is pressed or the initial operation is in process.

Battery
If the batteries of the remote control are flat, the battery symbol ****exchange the batteries (see chapter “Battery Replacement”).

Energy Saving Mode
The symbol ****shows that the appliance works in an energy saving mode, i.e. the current energy consumption is subject to the selected temperature and to the flow rate in the Energy Saving Mode.

Power Limit
If the full output of the instantaneous water heater does not suffice to heat the tapped quantity of water, this will be indicated by ****on the LCD.

Operation with Preheated Water
If the cold water inlet temperature is higher than the set value of the hot water outlet, the instantaneous water heater will not heat. In this case no power is emitted by the appliance and the sun symbol is displayed on the remote control screen.

Communication Of The Remote Control

• The remote control contacts the instantaneous water heater in regular intervals. In case of a temperature change at the instantaneous water heater or a water tapping without a previous key press on the remote control, the updated information on the display of the remote control may be shown with a slight delay.
• Without working radio connection, the appliance heats to the prior selected set value.

Battery Replacement

Replace the batteries with new AAA-batteries when the battery symbol

• Do not use rechargeable batteries!
• Non-rechargeable batteries are not to be recharged.
• Different types of batteries or new and used batteries are not to be mixed.
• When replacing the batteries, observe the correct polarity.

Disposal
Batteries may contain environmentally hazardous substances. Therefore, used batteries must be disposed of at special collecting points and not be mixed with general household waste. At the end of the remote control’s lifetime, the batteries must be disposed of separate from the appliance

Troubleshooting And Service

The following table will help you to determine and rectify the reasons for possible problems.

Display: “ E1 ” and appliance does not response to the remote

control

| Remote control is not registered

at the instantaneous water heater

| Register again, remove and insert

the batteries again.

Transmission range exceeded| Place the remote control closer to

the appliance, press button

Display: “ d1 ”| Registration in process| Hold the remote control in front of

the instantaneous water heater

Symbol “battery” lights| Flat batteries| Insert two new type AAA-batteries
Temperature changes unintentionally| Operation via other remote control, Smart Control app or

directly on the water heater

| Only register the desired remote control
Display “ E2 ”| PIN entered incorrectly

several times

| Wait afew minutes, perform re-registration

(see ch.5), enter the correct PIN

Display “ E9 ”| Connection error| If this happens repeatedly, replace the

batteries, contact customer service

warning: Repairs must only be carried out by authorised professionals.If a fault in your appliance cannot be rectified with the aid of this table, please contact German Pool Customer Service & Repair Centre.Please have the details of the typeplate at hand.

Warranty Terms & Conditions

Under normal operations, the product will gurantee a 1-year full warranty provided by German Pool (effective from the date of purchase).

This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:

• 1. Visit our website and register online: www.germanpool.com/warranty
• 2. Complete all the fields on the attached Warranty Card andmail it back to our Customer Service Centre.

Please fill out the form below. This information and the original purchase invoice will be required for any repairs. Warranty will be invalidated if information provided is found to be inaccurate.

Model No:

• Serial No.:
• Purchased From:
• Invoice No.
• Purchase Date

1. Customer who fails to present original purchase invoice will not be eligible for free warranty service.
2. Customer should always follow the operating instructions. This warranty does not apply to:
3. labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
4. damages caused by accidents of any kind (including material transfer and others);
5. operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs.
6. This warranty is invalid if:
7. the purchase invoice is modified by an unauthorized party;
8. the product is used for any commercial or industrial purposes;
9. the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
10.  the serial number is modified, damaged or removed from the product.
11. German Pool will, at its discretion, repair or replace any defective part.
12. This warranty will be void if there is any transfer of ownership from the original purchaser

This warranty is valid only in Hong Kong and Macau.

Specifications are subject to change without prior notice. If there is any inconsistency or ambiguity between the English version and the Chinese version, the English version shall prevail. Refer to www.germanpool.com for the most up-to-date version of the manual.

Customer Service & Repair Centre Hong Kong

• address: Unit B, G/F, Sunshine Kowloon Bay Cargo Centre, 59 Tai Yip Street. Kowloon, Hong Kong
• Tel : +852 2333 6249
• Fax : +852 2356 9798
• Email : repairs@germanpool.com

Macau

• address: 1 Andar A, Edf. Mei Kui Kuong Cheong Fase 2, 515 Av. do Conselheiro Borja,
• Tel : +853 2875 2699
• Fax : +853 2875 2661

References

• 德國寶German Pool | 家庭電器、廚櫃、傢俬 | 香港十大名牌

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>