GERMAN POOL GID-RS22T Free-Standing Ceramic Cooktop User Manual
- October 30, 2023
- GERMAN POOL
Table of Contents
GERMAN POOL GID-RS22T Free-Standing Ceramic Cooktop
Safety Instructions
- Before use, please remove the plastic bag, poly foam, leaflet, etc. to ensure that the body is clean, the bottom vent is not blocked, and the power cord or plug is not damaged. If the furnace surface is damaged, please contact our Customer Service & Repair Center for replacement to avoid danger.
- When using the product, it is necessary to use sockets with various technical indicators meeting the standards.
- Please use a pot of suitable size. The diameter of the pot shall not exceed 225mm and the pot shall be placed at the center of the furnace surface to avoid touching the silicon rubber ring.
- Please make sure the furnace and bottom of pot are dry and clean before heating. Do not heat an empty or dry pan. During cooking, do not leave for a long time.
- The product must be used in a place that children cannot touch.
- The product shall be placed on the level bench, avoid being used on the blanket, tablecloth or film to prevent the bottom vent from being blocked.
- The product will heat up quickly after opening. Please do not touch or move the product during the working process of the product and during ” ” flashing. The furnace surface is still hot during heating and after shutdown. Please keep away from combustibles such as paper, rags, curtains or cleaners to avoid fire!
- Do not heat paper, film, plastic and other inflammables on the furnace surface to avoid fire!
- Do not directly heat food on the furnace surface, especially the food with much oil and grease is easy to cause fire when heated!
- After shutdown, the fan is in normal operation when it is working for heat dissipation. Please do not pull out the plug immediately. Please do not touch or clean the furnace surface during the display screen flashing ” ” .
Product Structure
- Ceramic Glass Panel
- Control Panel
- Power Cord
- Silicon rubber ring
Control Panel
- LED DISPLAY
- HEAT ZONE
- TIMER
- INNER ZONE INDICATOR
- ON/OFF
- POWER
- OUTER ZONE INDICATOR
Operating Instructions
Utensil Selection
- There are not too many restrictions on the selection of pots and pans. All pots and pans made of high temperature resistant materials can be used.
- It is recommended to use smooth flat-bottomed pots and pans with size not more than 225mm in diameter, and placed in the center of the furnace surface for heating, to avoid touching the silicon rubber ring.
- Before heating, please make sure that the bottom of the pot is dry and clean, and there is no residue to avoid affecting the effectiveness of the product.
Quick Start Guide
| BUTTON | FUNCTION |
|---|---|
| ON/OFF | Turns the product ON and OFF |
| HEAT ZONE | Select DOUBLE RING, INNER RING ONLY or OUTER RING ONLY Mode |
| POWER | Adjust POWER OUTPUT |
| TIMER | Set COUNTDOWN TIMER |
Turns Product
ON and OFF
After plugging in the power source, product will emit a “BEEP” sound, and
Display Screen will show “—-“. Press 
, Display Screen will show “00”, and product
will enter into STANDBY MODE.
or
to enter into COOKING MODE
In STANDBY MODE, press 
or 
, product will enter into DEFAULT COOKING MODE of DOUBLE
RING /2200W, Display Screen will show “2200”.
Operating Instructions
Select HEAT
ZONE
When product is in COOKING MODE, press 
to select among DOUBLE RING, INNER RING ONLY and
OUTER RING ONLY modes.
| HEAT ZONE | DEFAULT POWER OUTPUT | INDICATOR LIGHT DISPLAY |
|---|---|---|
| DOUBLE RING | 2200W | Inner Zone |
Outer Zone Light On
INNER RING ONLY| 1100W| Inner Zone Light On
OUTER RING ONLY| 1100W| Outer Zone Light On
Adjust POWER
OUTPUT
When product is in COOKING MODE, press 
to adjust desired POWER OUTPUT.
| HEAT ZONE | DEFAULT POWER OUTPUT | INDICATOR LIGHT DISPLAY |
|---|---|---|
| DOUBLE RING | 300W-2200W | 300W, 600W, 900W, |
1200W, 1400W, 1600W,1800W, 2000W, 2200W
INNER RING ONLY| 100W-1100W| 100W, 300W, 500W,
700W, 900W, 1100W
OUTER RING ONLY| 100W-1100W| 100W, 300W, 500W,
700W, 900W, 1100W
Set TIMER
COUNTDOWN
When product is in COOKING MODE, press 
to set TIMER COUNTDOWN. Each short-press of
will add 1 minute
to Timer, each long-press of 
will add 10 minutes to Timer. (Minimum timer countdown is
1 minute, maximum is 3 hours). 3 seconds after Timer is set, product will
automatically start countdown, Timer and Power Level will display in
alternation. To cancel the Timer, press and hold 
for 3 seconds.
WARNING:
- When product is in use, DO NOT allow children near product to avoid danger!
- When product is in use, DO NOT touch or move product to avoid getting burnt!
- DO NOT unplug the product immediately after use, because the built-in fan system is still dissipating residual heat!
- Even after product is turned off, the product is still hot to the touch. DO NOT touch the product for at least 1 hour, to allow product to cool down completely. DO NOT touch, move or clean the product until it has completely cooled down!
- UNDER NO CIRCUMSTANCES should food be cooked directly on the cooktop surface. This product should be used with appropriate cookware at all times!
- DO NOT place any flammable items on top or around the vicinity of the product, such as paper, film, plastic, cloth, curtain etc. to avoid fire hazard!
Cleaning & Maintenance
- Before cleaning and maintenance, make sure product has been unplugged and the furnace surface has cooled to normal temperature!
- Do not wash product directly with water or immerse product in water.
- If there is cooking residue on the furnace surface, gently scrape off with a ceramic hob scraper at a 45 degree angle, and then wipe clean with a soft wet cloth. It can also be wiped with neutral detergent. Do not use corrosive liquid or steel scrubber for cleaning to avoid damaging the surface of the ceramic glass panel.
Error Code
| ERROR CODE | ANALYSIS | SOLUTION |
|---|---|---|
| E1 | Voltage lower than 90V | Check power supply first; if problem remains, |
contact Customer Service and Repair Centre
E2| Voltage higher than 280V| Check power supply first; if problem remains,
contact Customer Service and Repair Centre
E3| Sensor detects temperature higher than 750°F| Contact Customer Service and
Repair Centre
E4|
- Temperature sensor is short circuited or open circuited during operation
- Heating plate is burnt out and product cannot heat up
- Fuse is cut
- PCB power board malfunction
| Contact Customer Service and Repair Centre
E5| PCB power board overheated| Restart the product; if problem remains,
contact Customer Service and Repair Centre
E6| Sensor detects short circuit or open circuit| Contact Customer Service and
Repair Centre
E7| Fan malfunction| Contact Customer Service and Repair Centre
ATTENTION:
If problem remains unsolved, please contact Customer Service and Repair
Centre.
Disassembly and repair of this product must only be conducted by qualified
professionals.
Technical Specification
| Model | GID-RS22T-S |
|---|---|
| Rated Voltage/Frequency | 220V / 50Hz – 60Hz |
| Rated Power | 2,200W |
| No. of hob | 1 |
| Product Dimensions | (H)80 (Φ)280 mm |
| Net Weight | Approx. 1.9kg |
| Gross Weight | Approx. 2.2kg |
| Power Range | 100W – 2,200W |
- All information in this manual is for reference only. If there are any errors or omissions, the specifications produced by the factory shall prevail. Specification is subjected to change without prior notice.
- If there is any inconsistency or ambiguity between the English version and the Chinese version of this manual, the Chinese version shall prevail.
- Refer to www.germanpool.com for the most up-to-date version of the Operating Instructions.
Please read these instructions and warranty information carefully before use and keep them handy for future reference
Warranty Terms & Conditions
Under normal operations, the product will guarantee a 1-year full warranty provided by German Pool (effective from the date of purchase).
-
This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:
- Visit our VIP App and register online: (Scan the QR Code on the left)
- Visit our website and register online: www.germanpool.com/warranty
- Complete the attached Warranty Card and mail it back to our Customer Service Centre.
Please fill out the form below. This information and the original purchase invoice will be required for any repairs. Warranty will be invalidated if information provided is found to be inaccurate.
-
Customer who fails to present original purchase invoice will not be eligible for free warranty service.
-
Customer should always follow the operating instructions. This warranty does not apply to:
– labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
– damages caused by accidents of any kind (including material transfer and others);
– operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs. -
This warranty is invalid if:
– the purchase invoice is modified by an unauthorized party;
– the product is used for any commercial or industrial purposes;
– the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
– the serial number is modified, damaged or removed from the product. -
German Pool will, at its discretion, repair or replace any defective part.
-
This warranty will be void if there is any transfer of ownership from the original purchaser.
Customer Service & Repair Centre
Tel : +852 2333 6249
Fax : +852 2356 9798
Email : repairs@germanpool.com
Tel : +853 2875 2699
Fax : +853 2875 2661
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>