GERMAN POOL ADR-289 Smart UVC Clothes Drying Rack User Manual

GERMAN POOL ADR-289 Smart UVC Clothes Drying Rack

Please read these instructions and warranty information carefully before use and keep them handy for future reference.

Please register your warranty information now !
For Warranty Terms & Conditions,
please refer to the last page of this user manual.

Warnings & Safety Precautions

WARNING!

Read all instructions carefully before using this product.

• This product is for domestic indoor use only. If this product is used for any commercial, industrial, rental or other purposes, product warranty will be VOIDED.
• This product is not intended for use by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of this product by an adult responsible for their safety.
• Mind your children and DO NOT let children play with this product.
• Cleaning and user maintenance shall not be made by children without supervision.
• Check the voltage indicated on the rating label before using this product.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid hazards.
• Unplug this product from the power source before cleaning and maintenance.
• Contact German Pool authorized service technician for repair or maintenance of this product.

1. The ceiling selected for installing this product must be sturdy so that the expansion anchors can be embedded fully and securely.

2. DO NOT sharing the same power supply with other electrical appliances.

3. For safety reasons, this product must be earthed, and the mains voltage must correspond to the voltage stated on this product’s rating label. DO NOT use power cord with core thinner than 0.75mm2. In order to ensure the normal operation of this product, the main body of this product must be installed at a location where rain cannot reach.

4. DO NOT disassemble this product by yourself. Repair work must be carried out by German Pool
   Customer Service & Repair Centre.

5. DO NOT use this product during thunderstorms.

6. The connecting fixed wiring center must be equipped with an all-pole disconnecting device with a contact gap of at least 3 mm.

7. If the power cord is damaged, in order to avoid danger, it must be replaced by professionals from
   the manufacturer’s maintenance department or similarly qualified technicians.

8. WARNING! This product is specifically for drying woven fabrics.

WARNING!

• This product is equipped with a UVC lamp. DO NOT stare directly at the UV light source.
• DO NOT look at the UVC light from any angle to avoid causing permanent damage to the eyes.
• DO NOT shine the UVC light on bare skin, and DO NOT expose your skin to the UVC light.
• When UVC Button is pressed, UVC sterilization will activate immediately! DO NOT stand below or near this product when pressing the UVC Button!
• Stand away from this product before pressing the UVC Button; if this product is installed on the balcony ceiling, close the curtains before pressing the UVC Button to activate UVC Sterilization Function; if this product is installed in a room, leave the room and shut the door before pressing the UVC Button to activate UVC Sterilization Function.

Product Structure

Main Body

Installation Instructions

Installing The Expansion Anchors

1. Measure the ceiling installation location and mark the spots for the expansion anchors. If this product will replace your ceiling lamp, make sure to disconnect the power source of the ceiling lamp beforehand.
2. Tape the paper template guide to the ceiling, then drill four Ø10x80mm holes as marked on the template.
3. Install the expansion anchors into the drilled holes and tighten the screws. On one end, loosen the 2 lower bolts of the expansion anchors so that there is a 5mm gap between the upper and lower bolts; on the other end, take the 2 lower bolts off completely.
   
   Take off 2 lower bolts on one end
   
   Loosen 2 lower bolts 5mm on the other end

Installing The Main Unit

1. Remove the left and right end covers of the product, and insert one end of the main unit’s frame plate into the 5mm space of the expansion anchors (between the upper and lower bolts), then tighten up the lower bolts to secure this side of the frame plate.
   

2. Fit the other side of the main unit frame plate over the other 2 expansion anchors (the ones with the lower bolts removed) , then screw on the lower bolts so that the whole frame plate is securely installed.
   

3. Connect the wires correctly: Brown to live wire, blue to neutral wire, yellow-green to ground wire, then wrap the wires with insulating tape and lay them into the gap between the main unit and the ceiling.

Installing The Scissor Frame

1. Install one side of the scissor frame to the main unit and tighten the screws.
   

2. Thread the ball stopper of the steel cable into the small fitting on the scissor frame and make sure it is securely locked in. Repeat steps 1 and 2 with the other side of the scissor frame.

3. Snap on the end covers by aligning the latches with the holes on the main body and pushing inwards. Reconnect the power source of your original balcony lamp.
   

Installing The Extension Rods

1. Hook one end of the swing arm onto Extension Rod A, and the other end onto Extension Rod B, screw on the end cap tightly. Repeat with the other swing arm.
2. When you need to use Extension Rod B, swing it downwards, and swing it back up onto the hanger rod after use.

Installing The Hanger Rod

Align the screw hole at the base of the scissor frame with the screw hole near the end of the hanger rod, and tighten with screw. Do the same with the other three sides.

Operation Instruction

WARNING!

• This product is equipped with a UVC lamp. DO NOT stare directly at the UV light source.
• DO NOT look at the UVC light from any angle to avoid causing permanent damage to the eyes.
• DO NOT shine the UVC light on bare skin, and DO NOT expose your skin to the UVC light.
• Remote Control is equipped with a motion sensor, it is recommended that the remote control be installed next to the door of the room or balcony.
  

NOTE:
In any mode, when On/Off Button is pressed, product will turn off immediately. Pressing On/Off Button again will not turn the product back on. To turn the product back on, press your desired mode button.

Automatic Motion Sensor
This product is equipped with a motion sensor which will automatically turn the product on and off when motion is detected.

1. Automatically turn off UVC Lamp: When UVC Sterilization Lamp is turned on, and motion is detected near the remote control, the UVC lamp will automatically turn off and sterilization process will terminate.
2. Automatically turn on lighting: When power is connected, and motion is detected near the remote control, the lighting will automatically turn on; when lighting is turned on, if motion sensor does not detect any motion, the lighting will automatically turn off.

LAMP

| Lighting Lamp| Press this button to turn the lighting on or off.

UP

| Up|

• Press this button to raise the hanger rod.
• Hanger rod will automatically stop when it is completely raised up.

ON/OFF

| On/Off| In any mode, press this button to turn off the product.

STOP

| Stop| Press this button to stop the hanger rod from rising or lowering.

DRY

| Air Dry|

• Press this button to turn on or turn off Air Dry Function.
• Maximum drying time is 2 hours. Air Dry Function will automatically turn off after 2 hours.

UVC

| Sterilize|

• Press this button to turn on or turn off UVC Sterilization Function.
• Maximum UVC sterilizing time is 30 minutes. UVC Sterilize Function will automatically turn off after 30 minutes.
  WARNING! When this button is pressed, UVC Sterilization will activate immediately!
  DO NOT stand below or near this product when pressing the UVC Button!
  WARNING! Stand away from this product before pressing the UVC Button; if this product is installed on the balcony ceiling, close the curtains before pressing the UVC Button to activate UVC Sterilization Function; if this product is installed in a room, leave the room and shut the door before pressing the UVC Button to activate UVC Sterilization Function.

HEAT

| Heat Dry|

• Press this button to turn on or turn off Heat Dry Function; when Heat Dry Function is turned on, Air Dry Function will automatically turn on simultaneously.
• Maximum drying time is 2 hours. Heat Dry Function will automatically turn off after 2 hours, and Air Dry Function will automatically turn off as well.
• When Heat Dry Function is turned off, the fan will run for an extra 10 seconds to dissipate residual heat.

DOWN

| Down|

• Press this button to lower the hanger rod.
• Hanger rod will automatically stop when it has lowered down completely.

Troubleshooting

the power source
Remote control battery is dead| Replace the battery
UVC lamp does not light| Scissor frame is not retracted fully| Turn on the UVC lamp again after the scissor frame has retracted fully
UVC lamp is broken| Replace the UVC lamp
Hanger rod stopped midway| There is an obstruction stopping the hanger rod| Remove the obstruction
Motor overheat protection| Let the product cool down before restarting
Lighting lamp does not light| There is no power to the main unit| Connect the power source
Lamp is broken| Replace the lamp

WARNING!

If problem persists, please contact German Pool Customer Service & Repair Centre for assistance. DO NOT disassemble this product by yourself.

Technical Specification

Extended: (H) 1550±10mm (W) 2265±10mm (D) 505±5mm
Net Weight| 9.6 kg
Maximum Load| 35 kg

• Specification is subject to change without prior notice.
• If there is any inconsistency or ambiguity between the English version and the Chinese version, the Chinese version shall prevail.
• Refer to www.germanpool.com for the most update version of the user manual.

Warranty Terms & Conditions

Under normal operations, the product will guarantee a 1-year full warranty provided by German Pool (effective from the date of purchase).

This warranty is not valid until customer registration information is received by our Service Centre within 10 days of purchase via one of the following means:

1. Visit our website and register online:
   (Scan the QR Code on the left)

2. Visit our VIP App and register online: www.germanpool.com/warranty

3. Complete the attached Warranty Card and mail it back to our Card and mail it back to our Customer Service Centre.

1. Customer who fails to present original purchase invoice will not be eligible for free warranty service.

2. Customer should always follow the operating instructions. This warranty does not apply to:
   ● labour costs for on-site installation, check-up, repair, replacement of parts and other transportation costs;
   ● damages caused by accidents of any kind (including material transfer and others);
   ● operating failures resulting from applying incorrect voltage, improper usage, and unauthorized installations or repairs.

3. This warranty is invalid if:
   ● the purchase invoice is modified by an unauthorized party;
   ● the product is used for any commercial or industrial purposes;
   ● the product is repaired or modified by unauthorized personnel, or unauthorized parts are installed;
   ● the serial number is modified, damaged or removed from the product.

4. German Pool will, at its discretion, repair or replace any defective part.

5. This warranty will be void if there is any transfer of ownership from the original purchaser.

Customer Service & Repair Centre

Hong Kong

Unit B, G/F, Sunshine Kowloon Bay
Cargo Centre, 59 Tai Yip Street, Kowloon
Kowloon, Hong Kong
Tel : +852 2333 6249
Fax : +852 2356 9798
Email : repairs@germanpool.com

This warranty is valid only in Hong Kong and Macau

German Pool (Hong Kong) Limited

Hong Kong
Room 113. Newport Centre Phase II. 116 Ma Tau
Kok Road. Tokwawan. Kowloon. Hong Kong.
Tel: +852 2773 2888
Fax:+852 2765 8215

References

• 德國寶German Pool | 家庭電器、廚櫃、傢俬 | 香港十大名牌
• German Pool

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>