Whirlpool FFTN M11 82 Tumble Dryer Quick Start Guide

Whirlpool FFTN M11 82 Tumble Dryer

CONTROL PANEL

1. ON/OFF button (Reset if long pressed)

2. Program selection Knob

3. Start/Pause
   Options buttons

4. Dryness level

5. Start delay

6. Timed drying

7. Cycle end

8. Rapid (Key lock if long pressed)

9. Fresh care+ (Mute if long pressed)

INDICATORS

FIRST TIME USE

Make sure that the water tank is correctly inserted. Make sure that the drain hose on the back of the dryer is fixed correctly, either to the dryer’s water tank or to your domestic sewage system. The dryer must be installed in a room with a temperature ranging between 5°C and 35°C to ensure proper operation. Before you use your dryer ensure that it has been in an upright position for at least 6 hours.

DAILY USE

Doing this will keep your machine working at its BEST! Remember to empty your water tank after each drying cycle. Remember to clean your filters after each drying cycle. (Refer to section Care & Maintenance).

1. Open the door and load garments. Always refer to instructions on clothing labels and the max loads indicated in the program section. Empty pockets. Make sure garments do not get caught between the door and/or the door filter.
2. Close the door.
3. Press the button On/Off.
4. Select the program according to the laundry type.
5. Select the options, if necessary.
6. To start the cycle, press the Start/Pause button.
7. At the end of the drying cycle, a buzzer will beep. An indicator on the control panel signals the end of the cycle. Pull the load out immediately to prevent the formation of creases on the laundry
8. Turn the machine off by pressing the button On/Off, open the door, and pull clothing out. If the machine is not switched off manually, after about a quarter of an hour from the cycle end, the appliance turns off automatically to save energy. If this last stage is not carried out immediately, some machines and/or some programs/options are equipped with the Crease Care system. For some hours, after the end of drying, the drum rotates at regular intervals to prevent the formation of creases. In case of power failure, it is necessary to press the button Start/Pause to restart the cycle.

OPENING OF THE DOOR DURING THE CYCLE

During operation, it is possible to open the door. After having closed it, press the button Start/Pause again to restart the dryer.

PROGRAMS

Easy ironing
This cycle allows for the extension of the fibers of garments thus making ironing and folding easier. Do not use it in case of garments that are still wet. Suitable for small loads of cotton textiles or cotton blends.

CARE LABEL

Always check the care labels, especially when placing garments in the tumble dryer for the first time. Below are the most commonly used symbols:

• Maybe tumble-dried.
• Do not tumble dry.
• Tumble dry – high heat.
• Tumble dry – low heat.

The duration of these programs will depend on the size of the load, types of textiles, the spin speed used in your washer, and any extra options selected. In machines equipped with a display, the duration of the cycles is shown on the control panel.  The remaining time is constantly checked and adjusted during the drying cycle to show the best possible estimate.

Refresh: A short program suitable for refreshing fibers and garments by means of fresh air. Do not use it with garments that are still wet. It can be used with any load size but is more effective with small loads. The cycle duration is about 20 minutes.

OPTIONS

After selecting the program, various options can be set, if necessary.
Dryness level: Press the related button several times to obtain a different level of residual moisture on garments. An indicator signals the level being selected.
Iron dry: very delicate ironing. Suitable for making the ironing of garments easier immediately after the end of the cycle.
Hanger dry: a level intended for delicate garments ready to be hung.
Cupboard dry:  the garments are ready to be folded and put away.
Extra dry:  used for garments to be worn at the end of the cycle.
Timed drying: This option allows setting the drying time. Press the corresponding button to set the required time for drying. An indicator on the control panel signals the time being selected.
Start delay: This option allows you to set the delay of the cycle start. Press the corresponding button several times to obtain the required delay. After having reached the max. settable time, the option is reset by pressing the button again. An indicator on the control panel signals the time being selected. After having pressed the button Start/Pause, the machine signals the remaining time for the cycle to start. In case of the door opening, after closing, it is necessary to press the button Start/Pause.

Rapid: Enables quicker drying.

Fresh care+: If garments are left inside the drum after the end of the cycle, they are subject to bacterial proliferation. This option allows for preventing this proliferation by controlling the temperature and the rotation of the drum. This treatment has a max. duration of 6 hours after the end of the program set. This option remains in memory if selected in the previous drying. If this option is used together with the Start Delay, a crease treatment (a periodic rotation of the drum) is added in the Start Delay phase.

Key lock: This option makes all machine controls inaccessible, except the button On/Off. When the machine is on: to activate the option, keep the button pressed until the indicator goes on. To disable the option, keep the button pressed until the indicator goes off. This option remains in memory if selected in the previous drying.

Cycle end: This option activates a prolonged buzzer at the end of the cycle. Enable it if you are not sure to hear the normal sound at the end of the cycle. This option remains in memory if selected in the previous drying.

Mute: This option turns off all sounds of the control panel. Only warnings remain active.

• to activate the option, keep the button pressed until the indicator goes on.
• to disable the option, keep the button pressed until the indicator goes off.

OPTIONS BUTTONS

These buttons serve to personalize the selected program according to personal requirements. Not all options are available for all programs. Some options are incompatible with the ones previously set. The buzzer and/or blinking indicators will signal the incompatibility. If the option is available, the option indicator will stay on. Some options may be kept in the memory of the program if selected in the previous drying.

CARE AND MAINTENANCE

Unplug the dryer during the cleaning and maintenance procedures.

Emptying the water tank after each cycle (see Fig. A).
Pull the container out of the dryer and empty it into a sink or other suitable drain, then place it back. Do not use the dryer without having inserted the container back in place.

Cleaning the door filter after each cycle (see Fig. B).

Pull the filter out and clean it by removing the lint from the filter surface under running water or using a vacuum cleaner. For optimal performance, dry up all the filters before inserting them back in place. Do not use the dryer without having reinserted the filter in place.
Remove the door filter as described below:

1. Open the door and pull upwards.
2. Open the filter and remove lint from all its parts. Replace it correctly.

Ensure it is completely inserted flush with the dryer seal.

Cleaning the bottom filter when the relevant indicator turns on (see Fig. C).

Pull the filter out and remove the lint from its surface by washing it under running water or by using a vacuum cleaner.
However, it is advisable to clean this filter after each cycle to optimize drying performance. Do not use the dryer without having inserted the filter in place first.

Remove the bottom filter as described below:

1. Open the lower door.
2. Take the handle and pull the lower filter out.
3. Open the rear side of the filter and remove the lint from the inner surface of the mesh.
4. Clean the bottom filter chamber avoiding direct contact with the leaves.
5. Close the rear side of the lower filter and place it back by checking it is perfectly integrated into place.
6. Lower the filter handle and close the bottom door.
7. Make sure the air intake is free.

The filters are essential parts for drying. They are intended to collect the lint formed during the drying process. In the case of clogged filters, the airflow inside the dryer would be seriously affected: the drying times would be longer, the energy consumption would increase and the dryer could be damaged. If these procedures are not carried out properly, the dryer may not start.

TRANSPORT AND HANDLING

Never lift the dryer by holding it at the worktop.

1. Unplug the dryer.
2. Make sure that door and water tank are properly closed.
3. If the drain hose is connected to your sewage system, fix the drain hose on the rear of the dryer again (see Installation Guide).

Power consumption

off-mode (Po) – Watts| 0.50
left-on mode (Pl) – Watts| 1.00
Programs| Kg| kWh| Minutes
Eco Cotton| 8| 1.42| 165
Eco Cotton| 4| 0.78| 96
Synthetics| 4| 0.94| 113
*This is the reference program for the energy label and is suitable to dry normal wet cotton laundry. This is the most efficient program in terms of energy consumption for drying wet cotton laundry. (Standard/Default starting configuration).

Heat Pump System
The heat pump contains fluorinated greenhouse gases, contained in a hermetically sealed unit. This sealed unit contains 0.43 kg of the F gas R134a. GWP = 1430 (1 t CO2).

PRODUCT DESCRIPTION

1. Water Tank
2. Air Intake
3. Bottom filter
4. Door filter

TROUBLESHOOTING

Before contacting the Service Centre, refer to the table below. Often the malfunctions are minor and can be solved in a few minutes.

Insert the plug into the socket.
The plug is faulty.| Try to plug another appliance into the same socket. Do not use connecting electrical devices to the socket, as adapters or extensions.
A power failure occurred.| Await the reactivation of the power supply.
The tumble dryer does not start.| The door is open.| Close the door.
A time delay for the cycle start was set.| For machines equipped with this function: await the end of the delay set or switch the machine off to reset it. Refer to the section Options.
The button Start/Pause was not pressed to start the program.| Press the button Start/Pause.
The function Key Lock was enabled (in the case of machines equipped with this option).| Refer to the options section and, if the Key Lock is present, disable it. Switching the machine off is not enough to disable this option.
The drying times are very long.| Appropriate maintenance was not carried out.| Refer to the section Care & Maintenance and perform the operations described.
The program, the time, and/or the drying level set are not suitable for the type and theamount of load inserted into the dryer.| Refer to the section programs and options to find the program and the options most suitable for the type of load.
The garments are too wet.| Carry out a washing cycle with a higher spin speed to remove as much water as possible.
The dryer may be overloaded.| Refer to the program section to check the max. load for each program.
Room temperature.| The drying time may be longer if the room temperature falls outside the 14–30°C range.
The program did not end.| A power failure occurred might have occurred.| In case of power failure, it is necessary to press the button Start/Pause to restart the cycle.
Program finishes and clothes are dampers than expected.| Small load.| The automatic program has not sensed the required final moisture and the dryer will complete the program and stop. If this happens simply select an additional short period of drying or select an extra dry option if available.

Lights on or flashing

Water tank| The water tank is full.| Empty the water tank. Refer to the section Care & Maintenance.
---|---|---
Door filter and/or bottom filter| Failure of the airflow necessary for machine operation.| Clean the door filter and the bottom one and check whether the air intake is free. Carrying out these operations improperly may cause damage.
Bottom filter| The bottom filter requires cleaning.| Clean the bottom filter. Refer to section Care & Maintenance.
DEMO
The cycle lasts a few minutes.| The dryer is in DEMO mode. The DEMO indicator is on.| Disable the DEMO mode. The following actions must be carried out in sequence, without breaks. Switch the machine on and then switch it off again. Press the Start/Pause button until the buzzer is heard.
Switch the machine on again. The “DEMO” indicator flashes and then turns off.
The presence of a wrench symbol signals a malfunction.| The machine sensors detected a failure.| Switch the dryer off and unplug it. Open the door immediately and pull the laundry out, to allow the heat to dissipate. Wait for about 15 minutes. Reconnect the dryer to the power supply, load the laundry, and restart the drying cycle. If the problem still occurs, contact the After-Sales Service Centre and communicate the letters and digits flashing on the display.
For instance: F3 and E2.

Note: some models are self-cleaning and not equipped with a bottom filter. Please refer to the section Care & Maintenance.

FAQ’s

How long does it take a Whirlpool dryer to dry a load?****

The length of a drying cycle might vary based on the cycle, heat setting, and size of your load, but it usually lasts around 45 minutes. While heavier cycles, like bedding, might take up to three hours to thoroughly dry, delicate cycles typically take 15 minutes.

What setting on the Whirlpool dryer is Tumble dry?****

Each dryer set that you may choose from is regarded as a tumble dry setting. Most dryers let you choose a cycle with established settings, such as Normal, Delicate, Heavy Duty, or Fast Dry, as well as a time, heat level, and dryness level.

Does a dryer from Whirlpool need water?****

Water access is entirely optional.

Why doesn’t Whirlpool dryer dry clothes?****

Although they are typical causes of a dryer not drying clothes completely or correctly, a clogged or filthy lint screen and a blocked or obstructed dryer vent is not always the cause of a dryer, not heating.

What are the Whirlpool dryer’s heat settings?****

To properly care for your clothing, dryers from the Whirlpool brand can be set to no heat, timed dry, normal, permanent press, tumble dry, less dry, drier, and very dry.

How hot are Whirlpool dryers?****

Even after the appropriate air temperature has been established, a defective element may still be operating. Your dryer will overheat if this happens.

Why does my Whirlpool dryer turn itself off after just a short while?****

Drive belt damage or failure is the most frequent reason for a dryer to turn off after a short period of time.

Can a Whirlpool dryer be stopped?****

Throughout the cycle, you can stop the dryer at any moment.

What does the tumble dry icon look like?****

The presence of a square with a circle within signifies that the item may be tumble dried safely, and the number of dots inside the tumble dry symbol designates the appropriate temperature setting—one dot denotes low heat, two dots, medium heat, and three dots, high heat.

What is the tumble dry cycle?****

“Tumble dry” means that, as opposed to hanging or lying flat to dry, the article of clothing may be dried in a dryer. Clothes with laundry labels indicating that tumble drying are safe can be dried on the suggested heat setting.

My Whirlpool dryer is hot, but my clothes aren’t drying.****

The vent may be blocked if your dryer feels really hot but it takes an eternity to dry your garments.

Is air required for a dryer?****

For drying to be successful, dryers must have a lot of air moving through them.

Do dryers shut off on their own?****

When the heat is turned off, the cycle selection moves forward until the dryer shuts off on its own.

What is a Whirlpool dryer’s typical temperature?****

The water in your clothes is heated by your dryer, which turns it into vapor. Most dryers can reach temperatures of 125 to 135 degrees Fahrenheit on average. It’s crucial to remember that water can begin to steam and evaporate even before it reaches the boiling point.

What is the ideal dryer temperature?****

Most dryers exhaust moisture outdoors in order to remove it. The most effective dryers can swiftly dry your clothing at a hot temperature without scorching or harming them. Under-150°F temperatures are moderate enough to dry the items without injury.

Download this PDF Link:Whirlpool FFTN M11 82 Tumble Dryer Quick Start Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>