GOLDEN LIGHTING 1084-5FM BLK-BW Erma Matte Black Flush Mount Lighting Instruction Manual
- June 9, 2024
- GOLDEN LIGHTING
Table of Contents
GOLDEN LIGHTING 1084-5FM BLK-BW Erma Matte Black Flush Mount Lighting
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure
the best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
How to Identify the Fixture’s Wires
- Hot: Smooth, Black, or Transparent with Black Inner Thread
- Neutral: Ribbed, White or Transparent with White Inner Thread
- Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Get help, quick tips, and explore curated content:
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power
at the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap (A) assembly from the parts bag.
One end of the nipple (D) should be attached to the mounting strap (A) with a
washer (B) and hex nut (C) in place. 2. Use a screwdriver and mounting screws
(F) to attach the mounting strap (A) to the junction box. About half of the
exterior threads of the nipple (D) should be exposed, allowing the finial (H)
to fit snugly onto the nipple (D). Test to ensure that with the ceiling pan
(G) in place, the finial (H) fits onto nipple (D). 3. Remove the ceiling pan
(G) and set it aside for later.
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
5. Raise ceiling pan (G) up mounting strap (A) lining up the nipple (D) so
that it protrudes through the hole in the center of the ceiling pan (G).
Secure the ceiling pan (G) in place by threading the finial (H) onto the
exposed threads of the nipple (D). Adjust until shade is hung straight.
Carefully install light bulbs (not provided) that are in accordance with the
fixture’s specifications into sockets (J). Do not exceed the maximum
recommended wattage. Your installation is now complete. Turn on the power and
test the fixture.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>