GOLDEN LIGHTING 6952-M Matte Black Audra 12 Inch Wide Pendant with Clear Glass Shade Installation Guide
- June 9, 2024
- GOLDEN LIGHTING
Table of Contents
6952-M Matte Black Audra 12 Inch Wide Pendant
with Clear Glass Shade
Installation Guide
6952-M Matte Black Audra 12 Inch Wide Pendant with Clear Glass Shade
For Customer Service, contact the place of purchase to arrange for replacement
parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Take the mounting strap assembly from the parts bag. Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & C) should be attached to mounting strap (B). You may need to tighten nuts (D) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (F) up to mounting strap (B). Line up the holes in canopy (F) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (F). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. Remove the canopy and then tighten nuts (D) onto mounting screws (A) to hold the screws in place. 2. Pull the house wire though the center of the mounting strap (B). Place mounting strap (B) over the junction box and secure in place with mounting screws (C). Tighten the screws securely with a screwdriver.
ASSEMBLING THE FIXTURE
3. Rods (I) are on the fixture’s wires, but not connected to the fixture. Measure to determine the correct number of rods needed for proper hanging height. Thread the fixture’s wires through rods (I) before threading the rods together and then onto post (J). Connect rods (I) together and then to the fixture body at post (H). Tighten to secure using wrench tool if necessary. To lengthen the fixture, add additional rods. If additional rods are desired, contact the place of purchase to order. To shorten the fixture, slide any excess rods off the fixture’s wires to discard. Trim the wires after adding at least 8 to 10 inches of wire to the desired length.
CONNECTING THE WIRES
4. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the impairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
5. Push canopy (F) up to the ceiling and tightly thread nuts (G) onto the
exposed threads of mounting screws (A). Push shade (L) up over the threads of
socket (K). Secure the shade (L) in place with socket ring (M) and socket
cover (N) by twisting socket cover (N) onto the socket (K). Install a light
bulb (not provided) based on the fixture’s specifications. Do not exceed the
maximum wattage. Your installation is now complete. Turn on the power and test
the fixture.
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure
the best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Assembly Instructions: 6952-M
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
@GoldenLighting
@GLFixtures
** @GoldenLighting1
@GoldenLighting
GoldenLighting.com**
Documents / Resources
|
GOLDEN LIGHTING 6952-M Matte Black Audra 12 Inch Wide Pendant with Clear
Glass
Shade
[pdf] Installation Guide
6952-M Matte Black Audra 12 Inch Wide Pendant with Clear Glass Shade, 6952-M,
Matte Black Audra 12 Inch Wide Pendant with Clear Glass Shade, Matte Black
Audra 12 Inch Wide Pendant, Audra 12 Inch Wide Pendant, 12 Inch Wide Pendant,
Wide Pendant, Pendant
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>