GOLDEN LIGHTING 1084-SF BLK-BW 3 Lights Semi-Flush Mount Light Installation Guide

June 9, 2024
GOLDEN LIGHTING

GOLDEN LIGHTING logo 1084-SF BLK-BW
3 Lights Semi-Flush Mount Light
Installation Guide

1084-SF BLK-BW 3 Lights Semi-Flush Mount Light

Thank You for Choosing Golden Lighting for Your Lighting Needs!GOLDEN
LIGHTING 1084-SF BLK-BW 3 Lights Semi-Flush Mount Light - Figure
1

Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant for every 24″ of island. Fixtures should hang at least 30″ above the countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″ narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for any opening doors.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…

Assembly Instructions: 1084-SF

How to Identify the Fixture’s Wires

Hot: Smooth, Black, or Transparent with Black Inner Thread
Neutral: Ribbed, White or Transparent with White Inner Thread
Ground: Copper, Bare Metal, Green, or Transparent Inner Thread

https://qrco.de/bbv8UC
Get help, quick tips, and explore curated content
GOLDEN LIGHTING 1084-SF BLK-BW 3 Lights Semi-Flush Mount Light - Figure
3

For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:

  • All installation work should be done by accredited professional.
  • Shut off power supply at fuse or circuit breaker!
  • Use only the specified bulbs. Do not exceed the maximum wattage!

Assembly Instructions:

PREPARING FOR INSTALLATION

Carefully remove the new fixture from the carton as well as the yellow bag that holds all of the parts. See the important notes above. Shut off power at the circuit breaker and remove old fixture from wall, including the old mounting strap. 1. Take the mounting strap (B) assembly from the parts bag. Mounting strap (B) contains several threaded holes. Two sets of mounting screws (A & C) should be attached to mounting strap (B). You may need to tighten nuts (D) that hold mounting screws (A) in place. If the screws are not attached, please hold canopy (I) up to mounting strap (B). Line up the holes in canopy (I) with the holes in mounting strap (B) and insert mounting screws (A) into mounting strap (B) so that mounting screws (A) protrude through the holes in canopy (I). Mounting screws (A) are long, so please test the canopy against the mounting strap to see how far you should insert the screws. 2. Attach mounting strap (B) to the junction box using mounting screws (C) and a screwdriver. Tighten securely. Pull the house wires through the center of mounting strap (B).
ASSEMBLING THE FIXTURE
3. Feed the fixture wires from post (L) through the rod (K) and canopy (I). Pull the wires until taut. Thread rod (K) onto the post (L) and secure. Thread washers (H and G) and nut (F) onto wires as shown on the diagram. Lock thread rod (K) to canopy (I) using washers (H and G) and nut (F).

CONNECTING THE WIRES

4. Have an assistant support the fixture’s weight while completing the wiring. Refer to the wiring diagram and attach the fixture’s wires to the power supply wires from the junction box. Attach the fixture’s wires to the power supply wires from the junction box. Connect Hot to Hot (transparent wire with black inner thread, black, or smooth wire) Neutral to Neutral (transparent wire with white inner thread, white, or ribbed wire), and Ground to Ground (transparent wire with green inner thread, green wire, or copper). Twist the ends of the wire pairs together, and then twist on a wire connector. Make sure all twists are in the same direction. If there is no house ground wire coming from the junction box, locate ground screw (E) on the mounting bracket/mounting strap and wrap the fixture’s ground wire around the ground screw. Use a screwdriver to  tighten the top of ground screw (E) onto the wires and into the mounting bracket/mounting strap. Tuck the wires into the junction box.
FINISHING THE  INSTALLATION
5. Push canopy (I) up to the ceiling over mounting strap (B) so that mounting screws (A) protrude through the holes in the canopy. Tightly thread decorative nuts (J) onto the exposed threads of mounting screws (A) to secure canopy (I) until snug against the ceiling. 6. Install light bulbs (not provided) into sockets (M) in accordance with the  fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is now complete. Turn on the power and test the fixture.

GOLDEN LIGHTING logoGoldenLighting.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

GOLDEN LIGHTING User Manuals

Related Manuals