GOLDEN LIGHTING 0865-FM AGV-TEAL Kinsley 2 Light 14 Inch Wide Semi Flush Ceiling Fixture Instruction Manual
- June 9, 2024
- GOLDEN LIGHTING
Table of Contents
0865-FM AGV-TEAL Kinsley 2 Light 14 Inch Wide
Semi Flush Ceiling Fixture
Instruction Manual
0865-FM AGV-TEAL Kinsley 2 Light 14 Inch Wide Semi Flush Ceiling Fixture
Thank You for Choosing Golden Lighting for Your Lighting Needs!
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor. Allow clearance for
any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
Get help, quick tips, and explore curated content
For Customer Service, contact the place of purchase to arrange for
replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Remove the mounting strap assembly from the parts bag.
Mounting strap (B) contains several pairs of threaded holes. Find the pair of
holes that matches the spacing of the holes on the junction box. Two sets of
mounting screws (A & D) should be attached to the mounting strap (B). You may
need to tighten nuts (C) that hold mounting screws (A) in place. If the screws
are not attached, please hold canopy (F) up to mounting strap (B). Line up the
holes in canopy (F) with the holes in mounting strap (B) and insert mounting
screws (A) into mounting strap (B) so that mounting screws (A) protrude
through the holes in canopy (F). Mounting screws (A) are long, so please test
the canopy against the mounting strap to see how far you should insert the
screws. Remove the canopy (F) and tighten nuts (C) onto mounting screws (A) to
hold the screws in place. 2. Place mounting strap (B) over the junction box.
Secure mounting strap (B) to the junction box with mounting screws (D) and use
a screwdriver to tighten the screws firmly. Pull house wires through the
center of the mounting strap (B).
ASSEMBLING THE FIXTURE
No Assembly Required – This item arrives assembled and ready for installation.
Please proceed to the next step.
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
4. Hold canopy (F) up to mounting strap (B) so that the holes in the mounting strap (B) line up with the holes in the canopy (F). Lift canopy (F) until mounting screws (A) protrude through the holes in the canopy (F). Thread the decorative nuts (G) onto the exposed threads of mounting screws (A) until canopy (F) is snug against the ceiling. Install light bulbs (not included) into sockets (H) in accordance with the fixture’s specifications. Do not exceed the maximum recommended wattage. Your installation is complete. Turn on the power and test the fixture.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
GoldenLighting.com
@GoldenLighting
@GLFixtures
@GoldenLighting1
@GoldenLighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>