SIGURO Built-in Cooker Hood Instruction Manual

Built-in Cooker Hood
Instruction Manual

Built-in Cooker Hood

Translation of the operating instructions from the original language.

Thank you for purchasing a SIGURO appliance. We are grateful for your trust and are pleased to introduce the device to you on the following pages and introduce you to all its functions and uses.
We believe in a fair and responsible company, and therefore we only work with suppliers who meet our strict criteria to protect the interests of employees, prevent their abuse and fair working conditions.
If you need help with extensive maintenance or repair of the product that requires intervention in its internal parts, our authorized service is available to you at the e-mail address siguro@alza.cz or the operator on the vendor’s helpline. For your convenience, in solving any problems with the product, we have unified these contact points and the above contacts can be used in case of any complaints or post-warranty service.

SAFETY INFORMATION

Please read this manual carefully before use and keep it for future reference.

1. This appliance is intended for use by children 8 years of age and older and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, provided they have been given supervision or instruction concerning use of the appliance in a safe manner and understand the potential hazards.
2. Children must not play with the device.
3. Cleaning and user maintenance must not be performed by children without supervision.
4. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a dangerous situation.
5. Provide adequate room ventilation if the range hood is used at the same time as appliances burning gas or other fuels, except for appliances that only blow air back into the room.
6. Carry out the method and frequency of cleaning according to the instructions in the “Cleaning and maintenance” chapter. Follow all instructions in this manual.
7. WARNING: There is a risk of fire if cleaning is not carried out according to the instructions.
8. It is forbidden to flambé or use an open flame under the hood.
9. WARNING: When using cooking appliances, accessible parts can become hot. Take extra care. There is a risk of serious burns and injury if used incorrectly.
10. The extracted air must not be vented into a chimney used to exhaust fumes from appliances burning gas or other fuels, with the exception of appliances that only discharge air back into the room.
11. The minimum distance between the surface of the hob and the lowest part of the hood is 65 cm.
12. Follow the regulations regarding venting the extracted air.
13. This range hood is only intended for installation above a hob with a maximum of four cooking zones.
14. Follow the installation instructions in this manual.
15. Use the supplied mounting kit or a kit recommended by the manufacturer to attach the range hood.
16. WARNING: Incorrect installation of screws or attached devices specified in the instructions may result in an electrical hazard.
17. The range hood is designed to extract steam and vapors during cooking in the home. Do not use it in a commercial establishment. Do not use it for purposes other than those for which it is intended.
18. Before connecting the plug of the power cord to the mains socket, make sure that the voltage on the rating plate corresponds to the voltage in your socket.
19. Connect this range hood only to a properly grounded outlet. Do not use extension cords, portable extension sockets, adapters or other similar devices.
20. Switch off the hood and disconnect the power supply plug whenever you clean it, change the lighting, assemble or disassemble it.
21. When replacing lighting, always use the same type of fluorescent light specified by the manufacturer.
22. This range hood cannot be used as a support surface.
23. If the hood is damaged, contact an authorized service center to have it repaired. Never repair it yourself. There is a risk of injury from electric shock.

Lighting specifications

Overview

•  Outlet opening
• Outer shell
• Control panel
• Lighting (located on both sides)
• Front panel
• Remote control

Not shown

• Motor unit
• Grease filter
• Carbon filter (1 pc)
• Return chimney valve

Control panel

| On/off button with display
---|---
Timer button
Power down button
Power up button
Light on/off button
Remote control sensor
Remote control
| Power up/timer setting button
Power down/timer setting button
Timer button
Light on/off button

TECHNICAL SPECIFICATIONS

INSTALLATION

WARNING:
Incorrect installation of screws or attached devices specified in the instructions may result in an electrical hazard.
Warning:
Make sure the hood is turned off and disconnected from the power source prior to installation.
Supplied mounting kit:
2× fixing washer
4× fasteningscrew
Plan

Installation instructions
The minimum distance between the surface of the hob and the lowest part of the hood is 65 cm. The range hood is designed both for extraction into the chimney and
for air recirculation.
We recommend that two adults perform the installation.

1. Chimney flue
   The fumes are vented out of the building using a suction pipe that is connected to a non-return valve at the top of the hood. The diameter of the suction pipe must match the diameter of the non-return valve. The suction pipe is not included in the package. If the range hood has been used with a carbon filter, it must be removed if it is to be used again with a chimney flue.

2. Recirculation
   During recirculation, air is discharged back into the room. The intake air is degreased and deodorized, and is then discharged back into the room.
   A carbon filter must be installed before using the hood in this way.

Installation

1. Cut a hole of the appropriate size in the cabinet where you will install the cooker hood.
   Note:
   The depth of the cabinet must not be less than 26 cm. A free space of 5 cm must be left at the front and back.

2. Loosen the four screws of the front panel, remove the decorative frame and slightly tilt the front panel to disconnect the cables. After disconnecting, put the front panel and decorative frame aside.

3. Loosen the screws of both fixing washers, which are located on the sides of the cooker hood.

4. Insert the cooker hood into the opening in the cabinet.

5. Carefully push the fixing washers outwards to release them from the hood. It is important that the hood in this case is inserted deeper in the cabinet so that the washers can be easily pushed out.

6. Once the washers are fully extended, carefully place the hood down until the extended parts of the washers rest on the cabinet inside.

7. Secure the fixing washers with the screws and make sure they are firmly tightened.
   Note: Depending on the cabinet ty, it will be necessary to drill a 24 × 11 mm hole to allow the washers to fit easier in the cabinet. Such openings have to be drilled before inserting the hood into the cabinet.
   The fixing washers have an adjustable range of 6 to 28 mm, depending on the thickness of the wood layer.

8. Attach the decorative frame to the hood body with four screws. Make sure that they are properly tightened.

9. Attach the front panel to the hood body and plug the line back in.

10. First insert the back part of the panel into the hood body and then the front part of the panel. Secure using screws. Make sure they are well tightened.

11. Insert the non-return valve on the outlet opening in the upper part of the hood

12. Attach the end of the suction pipe to the nonreturn valve in the upper part of the range hood.

13. Chimney flue Attach the other end of the suction pipe to the flange in the wall. It must have a diameter corresponding to the suction pipe. A smaller diameter can cause lower suction performance and higher noise when using the range hood. Do not bend the suction pipe excessively. The maximum bending angle is 90°. To ensure efficient suction performance, we recommend bending the suction pipe only once.

14. Recirculation: Cut a hole in the top of the cabinet of the same diameter as the suction pipe. Insert a protective grille specially designed for recirculating air into the room in the opening. Attach the other end of the suction pipe to the protective grille from below.

Electrical wiring
Before plugging the range hood into the mains socket, make sure that the voltage indicated on its rating plate matches the voltage in your mains socket. If in doubt, contact your electricity supplier.
If the socket needs to be modified, always contact a qualified electrician. The electrical wiring must be carried out in accordance with the valid regulations and directives in force in the country of installation.
The range hood is equipped with an electrical plug, which you plug into a properly grounded electrical outlet after installation.
We recommend that the electrical socket to which the range hood will be connected be placed in a separate circuit with its own circuit breaker.

USE

Before first use
Wipe the outside of the appliance with a soft sponge slightly moistened with warm water.
Inserting the carbon filters
Note:
Do this step if you are using the recirculation method.

1. Remove the front panel and carefully remove the grease filter.
2.  Insert the new filter on one side of the motor unit and turn the filter clockwise to secure it.
3. Install the grease filter and front panel.

Switching On/Off
After connecting the hood to the electrical socket, all buttons and indicator lights will light up briefly and then go out. The on/off button and the display will light up white.
Press and hold the on/off button to turn on the hood. All indicator lights will light up briefly and the display will show “0”. The cooker hood switches to standby mode.
If you are not going to use the hood, press the on/off button and the hood will turn off.
Note:
In standby mode, the hood automatically switches off after 2 minutes of inactivity.
Power setting
While the hood is on, adjust its power using the buttons on the control pan- el of the hood or using the +/- buttons on remote controll. You can set the power from 1 to 3, where 1 represents the lowest power and 3 the highest power. If the display shows “0”, the cooker hood stops and switches to standby mode.
Timer

1. When the hood is on, press the button for 3 seconds.
2. The display flashes and you can set the time of automatic switch-off time from 1 to 9 minutes, using the buttons on the control panel of the hood or or +/- buttons on remote control.
3. Press again the button to save the setting. If you do not take any action within 10 seconds, the settings will be saved automatically.
4. When the cooker hood motor is on and the timer is set, it can be adjusted as described above (steps 1 to 3). The display shows the countdown of the set timer time.
5. If you want to set the timer while the hood is off, follow the instructions above (steps 1 to 3). However, the countdown will only start when you turn on the hood.

Turn lighting on/off
Press briefly the button on the control panel or on remote control and the lighting turns on. Press the button again to turn the lighting off.
Remote control
The remote control is supplied with inserted batteries from the manufacturer. To use the remote control, remove the protective film from the battery compartment. It protects the battery from discharge and damage during transport.
If you want to use the remote control, point it at the sensor on the control panel. The maximum range of signal sent from the remote control is 6 m. If obstacles are located between the remote control and the appliance, the signal cannot be transmitted. If the inserted battery is empty it needs to be replaced by the same type. Proceed as follows:

1. Slide the cover with the battery compartment from the bottom of the remote control.
2. Remove the depleted battery and insert a new 3V CR2032 battery. Observe correct polarity when inserting a battery.
3. Insert cover with the compartment back into the remote control.

If you will not use the remote control for a long time, we recommend removing the battery. If the battery leaks into the interior of the remote control, it could damage it.
Warning:
Never put batteries in fire, short circuit or damage them in any way. After the end of their lifetime, discard them in environmentally friendly manner. Never dispose of batteries in household waste.
Pairing the remote control with the cooker hood.

1. While the hood is off, press the button for 2 seconds, the indicator starts flashing and a beep sounds.
2. Press any button on the remote control and a beep will sound. The light will turn off and the pairing has been completed successfully.
3. If you do not press any button on the remote control within 3 seconds, the light will go out and the hood will turn off.

Note:
Pairing only needs to be done once before first use, or if the internal memory of the hood has been cleared.

CLEANING AND MAINTENANCE

Always switch off the appliance, disconnect the power cord plug from the mains sock- et prior to cleaning or any maintenance.
Warning:
Never immerse the appliance, power cord or plug in water or other liquids.
Do not use plastic or metal scrapers, harsh cleaners, chemicals, petrol, solvents or other similar substances to clean any parts of the appliance. The surface finish could
be seriously damaged.
Regular cleaning
Use a soft sponge, slightly moistened in lukewarm water with a little detergent. Wipe with dry dish towel.
Grease filter
The grease filter has to be cleaned at least once a month. The grease filter captures grease, smoke and dust. It has a direct effect on the performance of the hood.
Warning:
There is a risk of fire if the grease filter is not cleaned regularly.

1. Remove the front panel and carefully remove the grease filter.
2. Wash the grease filter in warm water with a little dishwashing liquid.
3. Rinse and wipe dry.
4. Install in place and replace the front cover.

Warning:
Before installing the grease filter, make sure it is completely dry.
Note:
You can wash the grease filter in the dishwasher. Place it vertically in the upper basket to increase washing efficiency. However, the water temperature should not exceed 65°C. Carbon filter replacement
Note:
Do this step if you are using the recirculation method.
The carbon filter absorbs unpleasant odours from cooking. Its saturation occurs through long-term use, intensive cooking and regular cleaning of the grease filter.
We recommend changing the carbon filter every 3 months.

1. Remove the front panel and carefully remove the grease filter.
2. Turn the carbon filter counterclockwise to loosen it and carefully remove it.
3. Insert the new filter on one side of the motor unit and turn the filter clockwise to secure it. Make sure the filter is installed correctly. Improper installation can cause abnormal noise and vibrations, which can lead to damage to the hood.
4. Install the grease filter and front panel.

Warning:
The carbon filter must not be washed.
Light replacement

1. Switch off the hood and disconnect it from the power socket.
2. Loosen the screws of the lighting cover and carefully remove the cover.
3. Unscrew the fluorescent light.
4. Insert a new fluorescent light of the same type.
5. Replace the cover and fasten with screws.

Warning:
The fluorescent light heats up during use and may be hot even after it is turned off. Allow it to cool (at least 10 minutes) before replacing.

TROUBLESHOOTING

The motor is damaged.
Neither the lights nor the hood turn on.| The fluorescent light is broken.| Replace the fluorescent light.
The plug is not inserted properly in the socket.| Check the plug connection in the socket.
The range hood emits strong vibrations.| The fan is blocked.| Switch off the hood and contact an authorized service.
The fan motor is not prop- erly tightened.
The range hood is not properly installed.| Carefully remove the hood and reinstall it.
Poor hood performance.| The hood is placed too high above the hob.| The recommended distance between the range hood and the hob is 65 to 75 cm.

If the problem is not listed in the table above or if the problem persists, switch off the appliance, disconnect the plug from the electrical outlet and contact an authorized
service center.
DISPOSAL OF USED BATTERIES
**** Batteries contain materials harmful to the environment. Do not dispose of batteries in a regular community waste. Dispose of used batteries properly at collection points.
The use of the WEEE Symbol indicates that this product should not be treated as household waste. By ensuring this product is disposed of correctly, you will help protect the environment. For more detailed information about the recycling of this product, please contact your local authority, your household waste disposal service provider, or the shop where you purchased the item. This product meets all of the related basic EU regulation requirements.
The EU dec‑ laration of conformity is available on www.alzashop.com/doc.
This product sold in the European Union meet the requirements of Directive 2011/65/EU on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS).

Alza.cz, a. s., Jankovcova 1522/53, 170 00 Prague 7, Czech Republic
© 2022 Alza.cz, a. s. All Rights Reserved.
**www.siguro.net

**

Documents / Resources

| SIGURO Built-in Cooker Hood [pdf] Instruction Manual
Built-in Cooker Hood, Cooker Hood, Built-in Hood, Hood
---|---

References

• Alza.cz – rychlý a pohodlný nákup odkudkoliv | Alza.cz
• Siguro

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>