KICHLER 37418A 22 In 3 Light Distressed Black and Wood Tone Rustic Vanity Light Instruction Manual

KICHLER 37418A 22 In 3 Light Distressed Black and Wood Tone Rustic Vanity

Light

Product Information

• Item Numbers: 0759870, 0771556, 61325001
• Product Name: 3-Light Vanity
• Model Numbers: 37418A, 37421A

For any questions, problems, or missing parts, please contact our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. You can also visit our website at kichler.com/customer-care/contact-us.

Please note that this product may expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, please visit http://www.P65Warnings.ca.gov.

Package Contents

Hardware Contents

• Wire Connector (Qty: 3)
• Short Machine Screw (Qty: 2)
• Threaded Knob (Qty: 2)
• Long Machine Screw (Qty: 2)

Safety Information

Please read and understand the entire manual before attempting to assemble, operate, or install the product. Do not leave out any parts or use any parts that are worn out or broken, as it could invalidate the ETL listing and/or C.S.A. certification of the fixture.

WARNING

• CAUTION – RISK OF SHOCK –
  Disconnect Power at the main circuit breaker panel or main fusebox before starting and during the installation.

• WARNING:
  This fixture is intended for installation in accordance with the National Electrical Code (NEC) and all local code specifications. If you are not familiar with code requirements, installation by a certified electrician is recommended.

• Do not use bulbs with wattage greater than specified on this fixture.

• California Proposition 65

• WARNING: This product can expose you to chemicals including lead, which is known to the State of California to cause cancer, birth defects, or other reproductive harm.
  For more information, go to http://www.P65Warnings.ca.gov

• CAUTION

• If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate completely, please contact a licensed electrical contractor.

• All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are worn out or broken. Failure to obey this instruction could invalidate ETL listing and/or C.S.A. certification of this fixture.

Preparation

Before starting the assembly, ensure that all parts are present. Compare the parts with the package contents list and hardware contents list. If any part is missing or damaged, do not proceed with the assembly. Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

Estimated assembly time: 30 minutes to 1 hour

Tools Required for Assembly (not included): Phillips screwdriver, flathead screwdriver, wire strippers, electrical tape, ladder, safety glasses.

Assembly Instructions

1. Insert long machine screws (DD) through mounting bracket (B) so that they protrude outward. Orient the mounting bracket (B) with the raised center portion protruding into the outlet box (not included). Connect the mounting bracket (B) to the outlet box with short machine screws (BB).
   Hardware Used
   
   

2. Wire connection guide:

   • Ground wire:

   • For installation in the United States: Wrap ground wire from outlet box around ground screw preassembled on mounting bracket (B) no less than 2 in. from wire end. Tighten ground screw. If fixture is supplied with a ground wire, connect to outlet ground wire with a wire connector (AA).

   • For installation in Canada: If fixture is supplied with ground wire, wrap ground wire around ground screw on mounting bracket (B). Tighten ground screw. Connect fixture ground wire to outlet ground wire with the wire connector (AA).

   • Supply wires:

   • Connect the Neutral (White) supply wire from the outlet box to the Neutral fixture wire (White or Parallel Cord “D” shaped and ribbed).

   • Connect the Hot (Black) supply wire from the outlet box to the Hot fixture wire (Black or Parallel Cord round and smooth).
     NOTE: Fixture wires will either be:

   • Black and White.

   • Parallel Cord SPT-1 lamp wire with one round smooth wire and one “D” shaped ribbed wire.

   • Pass the canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure it in place with threaded knobs (CC).
     Hardware Used
     

3. Pass canopy (A) over the long machine screws (DD) protruding from the mounting bracket (B) and secure in place with threaded knobs (CC).

Hardware Used

4. Pass the shade (D) and spacer (F) over the socket (C) and secure them with the socket ring (E).
   NOTE: a wrench has been provided to assist in screwing the socket ring.

5. Insert a 60-watt max. medium base bulb or LED equivalent (not included) into the socket (C). Repeat this step for the remaining sockets (C).
   Repeat for remaining sockets (C).

Care and Maintenance

• Wash shades in an automatic dishwasher.
• Always be certain that electric current is turned off before cleaning this item.
• Use a soft, moist cloth with mild non-abrasive soap to clean fixture. Never use glass cleaner on fixture, as it will damage the metal finish.
• All glass shades may be washed in a towel-lined sink with warm water and mild soap. Do not wash shades in an automatic dishwasher.

Troubleshooting

2. Replace bulb.

REV 8-JUL-2022 Distributed by: Kichler Lighting LLC 30455 Solon Rd Solon, OH 44139

Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-800-554-6504, 8 a.m. – 4:30 p.m, EST, Monday – Friday. http://kichler.com/customer-care/contact-us

References

• Contact Kichler - Get in touch with us | Kichler Lighting
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>