Acuity Brands EVO 6 Round Downlight General Illumination LED Downlight Instructions

Acuity Brands EVO 6 Round Downlight General Illumination LED Downlight

LED IMPORTANT SAFETY INSTRUCTIONS

READ AND FOLLOW ALL SAFETY INSTRUCTIONS! SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER ATTER INSTALLATION

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.
• Before Installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards Involved. Regular fixture maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the retractor/lens. Frequency of cleaning will depend on ambient dirt level and minimum light output which is acceptable to user. Retractor/lens should be washed in a solution of warm water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe retractor/lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been property packed so that no parts should have been damaged during transit. Inspect to con­firm. Any part damaged or broken during or after assembly should be replaced.
• Recycle www.epa.govc : For Information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations In equipment nor to provide every possible contingency to meet in connection with Installa­tion, operation, or maintenance. Should further information be desired or should particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc.

WARNING
RISK OF ELECTRIC SHOCK

• Disconnect or turn of power before installation or servicing.
• Verify that supply voltage is correct by comparing it with the luminaire label information.
• Make all electrical and grounded connections In accordance with the National Electrical Code (NEC) and any applicable local code requirements.
• All wiring connections should be capped with UL approved recognized wire connectors.

WARNING
RISK OF BURN

• Allow lamp/1ixture to cool before handling. Do not touch enclosure or light source.
• Do not exceed maximum wattage marked on luminaire label.
• Follow all manufacturer’s warnings, recommendations and restrictions for: driver type, burning position, mounting locations/methods, replacement and recycling.

CAUTION RISK OF INJURY

• Wear gloves and safety glasses at all times when removing luminaire from carton, installing, servicing or performing maintenance.
• Avoid direct eye exposure to the light source while it is on .

CAUTION
RISK OF FIRE

• Keep combustible and other materials that can burn, away from lamp/lens.
• Do not operate in close proximity to persons, combustible materials or substances attected by heat or drying.

CAUTION: RISK OF PRODUCT DAMAGE

• Never connect components under load.
• Do not mount or support these fixtures in a manner that can cut the outer Jacket or damage wire Insulation.
• Never connect an LED product to an unapproved dimmer pack. Contact ABL directly for any dimmers not specifically recommended for the product.
• Unless individual product specifications deem otherwise: Allow for some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other material that will prevent convection or conduction cooling.
• Unless individual product specifications deem otherwise: Maximum ambient temperature is 90°C. Do not operate fixture at temperatures higher than this.
• Unless individual product specifications deem otherwise: Never mount in places where fixture will be exposed to rain, high humidity, extreme temperature changes or restricted ventilation.
• LED products are Polarity Sensitive. Ensure proper Polarity before installation.
• Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal ground­ing equipment must be worn during all Installation or servicing of the unit.
• Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter performance.
• There are no user serviceable parts inside the unit. Do not rewire, reconfigure, or modify the unit or attempt any repairs yourself. Additionally, field replacement of the LED assembly or lamps is not allowed by UL standards at this time. In the unlikely event your unit may require service, stop using the unit immediately and contact an ABL representative.

All luminaires that contain electronic devices that generate frequencies above 9kHz from any component within the luminaire comply with one of the following Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including Interference that may cause undesired operation.

This device complies with Part 18 of the FCC Rules but may cause interference with cordless and cell phones, radios, televisions, and other electronic devices. To correct the problem move the device away from the luminaire or plug into a dif­ferent outlet. This product may cause interference to radio equipment and should not be installed near maritime safety communications equipment or other critical navigation or communications equipment operating between 0.45-30MHz.

Failure to follow any of these instructions could void product warranties. For a com­plete listing of product Terms and Conditions, please visit www.acuitybrands.com.

OUR BRANDS
Acuity Controls I American Electric Lighting I Antique Street Lamps I Carandini Distech Controls I eldoLED I Gotham I Healthcare Lighting I Holophane I Hydrel Juno lighting Group I Lithonia Lighting I Mark Architectural Lighting I Peerless RELOC Wiring I Sunoptics I Winona
Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.
ABL LED General Warnings, Form No. 503.203
© 2010 Acuity Brands Lighting, Inc. All rights reserved. 12/01/10

INSTALLATION INSTRUCTIONS

CTAEVO4 / CTAEVO6

Upon receipt, thoroughly inspect for any freight damage which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the packing slip with the label on the carton to ensure you have received the correct merchandise.

IMPORTANT SAFETY INFORMATION

For Your Protection, Read Carefully

Warning: Risk of fire. Do not install insulation within 3 inches of fixture sides or wiring compartment, nor above fixture in such a manner as to entrap heat.

Electric current can cause painful shock or serious injury unless handled properly. For you safety, always remember the following:

• Turn off the supply power.
• Ground the fixture to avoid potential electrical shocks.
• Do not handle an energized fixture or energize any fixture with wet hands, when standing on a wet or damp surface, or in water.

SAVE THESE INSTRUCTIONS

1. Remove torsion spring brackets from mounting frame and retain the screws. (see Figure 1).
2. Insert yoke assembly through ceiling opening (see Figure 2).
3. Attach yoke assembly to mounting frame by inserting feet into raised bracket slots (see Figure 3). Feet will slide into place. Secure with retained torsion spring bracket screws (optional).
4. Pull the EVO light engine down into the ceiling opening (see Figure 4) and remove torsion spring yoke bracket from the EVO light engine (see Figure 5). Re-install top center screw to top of light engine, (do not screw all the way down, leave a small space).
5. Attach reflector to light engine (see separate instruction sheet, CJ5201007).
6. Carefully reach through the aperture and pull tab of constant force spring down through the aperture (see Figure 6). Always wear cut proof gloves while handling constant force spring.
7. Connect constant force spring to the top center screw of the light engine through the key hole on the tab of the constant force spring and tighten screw just enough to allow the reflector to rotate for adjustment (see Figure 7).
8. Do not release reflector, slowly allow spring to fully retract reflector into ceiling opening (see Figure 8) making sure that wallwash component (if present) is properly oriented with respect to the wall to be illuminated (see Figure 9).
9. If reflector does not rest tightly against ceiling, remove the reflector, loosen screws in yoke assembly, adjust appropriately, tighten screws.

CJ5202351 Rev. A
©2022 Acuity Brands Lighting, Inc. All Rights Reserved.
1/2022 2 of 4

References

• Home | Gotham Lighting

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>