LUMEX LL9P3 NOVABLADE LED Panel Instruction Manual
- June 3, 2024
- LUMEX
Table of Contents
LUMEX LL9P3 NOVABLADE LED Panel
INSTALLATION INSTRUCTIONS
Nova Blade Range
- Ensure that the power has been turned off before attempting installation.
- This product should only be installed by a licensed electrician.
- This product must be installed in compliance with all the requirements set out in AS/NZS3000 (current edition) and other relevant Standards and Regulation.
T-Bar Installation
-
Prepare an opening in the T-Bar system to suit the panel dimension.
-
Install a suitable standard three pin socket (240V 10A) adjacent to the mounting point.
Note: Lumex NovaBlade drivers have a 1.2M flex and plug provided. -
Drop the panel light into the T-Bar opening.
-
Connect the power supply to the panel connection with the polarized connector provided.
-
Connect power plug to socket.
-
Switch on and test.
Note: Use only Power Supply provided. Use of non standard power supply will void warranty. Do not modify, bend, or drill the panel. This will void warranty and may create a serious hazard.
Alternative Mountings
Lumex also offer a range of alternative mounting options for
NovaBlade which include:
Flush Mount for recessing into plasterboard or similar material.
Semi Flush for low profile surface mounts. The driver must be able to be
recessed.
Surface Mount for tidy solutions for the underside of concrete slabs and
similar situations.
Pendant Mount Kits for high ceiling or over task areas.
Air Handling Fixtures for negative pressure ceiling spaces.
Care & Cleaning
- Periodic Cleaning of your NovaBlade is the only maintenance that is needed.
- Use only a damp, lint-free cloth to remove dust.
- Avoid using chemical cleaners as some products degrade plastic material and can cause premature failure.
- Do not use water when cleaning as it could damage components and possibility cause an electrical shock.
Clearance From Combustible Materials & Insulation
Building Insulation must not cover this luminaire. Do not cover LED driver with thermal insulating material.
Warning:
Risk of overheating or fire if the clearance distances are compromised.
Dimension | Min. Clearance |
---|---|
SCB – Top clearance to combustible building element | 15mm |
MIC – Top clearance to bulk thermal insulation | 10mm |
HCB – Side clearance to combustible building element | 20mm |
SCI – Side clearance to bulk thermal insulation | 20mm |
Clearance between luminaire to independent LED driver | 0mm |
FOR NEW ZEALAND ONLY Warning: This luminaire is not suitable for
installation in locations where thermal insulation is present, or may
reasonably be expected to be installed in the future, or where there is a
likelihood of other combustible material, e.g. leaves or vermin debris, etc.
collecting on or around the luminaire. It is not suitable for domestic
installations or installation in residential areas of non domestic
installations (residential institutions, hotels, boarding houses, hospitals,
accommodation houses, motels, hostels and the like. If the external edible
cable or cord of this luminaire is damaged, it shall be exclusively replaced
by the manufacturer or his service agent or a similar qualified person in
order to avoid a hazard.
Reminder: ASINZS3000:2007 Amendment 2, Clause 4.5.2.3.2. Where recessed
luminaires are installed in an accessible roof space, a permanent and legible
warning sign shall be installed in the roof space adjacent to the access
panel, in a position that is visible to a person
SEVEN YEAR WARRANTY AGAINST DEFECTS
WARRANTY
Lumex Lighting (Australia Only)
With your new Lumex installation comes the quality assurance provided by the
seven (7) year or 35,000 operational hour Warranty (the “Warranty”) The
warranty is offered to you by Verbatim Australia Pty Ltd.
(“Verbatim”) of Unit 6,450 Princes Highway, Noble Park, VIC 3174
Phone contact: +61 (03) 9790 8999
Subject to the terms of this document, Verbatim warrants to the owner of the
Installation that Verbatim will repair or replace, without charge Lighting
product (the “Product”) if the Product fails due to any manufacturing defect
during the first seven (7) years or 35,000 hours of operation following
initial installation.
This Warranty applies from the date of invoice for a period of seven (7) years
or 35,000 hours of operation thereafter subject to the conditions set in this
Warranty.
A. Definitions
In this warranty:
-
Australian Consumer Law means the Australian consumer
law set out in Schedule 2 to the Competition and Consumer Act 2010. -
Goods mean the product or equipment that was purchased in Australia.
-
Manufacturer, We or us means Verbatim Australia Ply Ltd. ABN 39 005 706 37 4
-
Supplier means the authorized distributor or the licensed electrical contractor that sold you the Goods.
-
You means you, the original end-user purchaser of the Goods.
B. Warranty Period and Details
This product is covered by a seven (7) year or 35,000 hours of operation
installed warranty against manufacturing faults and defects, provided that:
- The product is properly installed, and installation is consistent with the manufacturer’s instructions, and is installed by suitably trained and qualified installer.
- The product is not subjected to any unauthorized modifications.
- The product is only used for the purpose of illumination, in line with its designated purpose or the designated purpose of a luminaire of its general type.
- The product use is in normal conditions and not exceeding a total of 35,000 hours over the warranty period.
- Any faults or defects attributable to the misuse, abuse, accident or non-observance of the manufacturer’s instructions on the part of the user are specifically excluded.
- Where a battery product is installed, the warranty period covers 12 months.
- Where a SmartSense™ product is installed, the warranty period covers five (5) years for the sensor technology only.
- Where a third party component is installed within, or as part of, a Lumex fitting, the warranty period is as dictated by the Original Equipment Manufacturer of the third party component. This Warranty DOES NOT COVER:
- Damage caused by acts of God, or other incidents/ occurrences beyond the control of Verbatim, including without limitation, fire, theft, storms, floods.
- Damage caused by water or other forms of moisture being absorbed by the LED light fitting.
- Damage caused by chemical impact or other abuse including environmental factors, improper cleaning solutions, damage from leaving substances such as bleach on the product.
- Damage or problems caused by the use of an accessory, component or equipment not supplied by Verbatim.
C. Extent of the Warranty
Verbatim do not cover freight charges (including insurance) or travelling cost
for repairs performed outside the area normally serviced by Verbatim or an
authorised repair agent.
- Goods that prove defective within the Warranty Period by reason of improper workmanship or faulty material, we may, at our own discretion, either repair or replace the Goods without charge.
- This warranty does not cover any cost related to removal, or reinstallation of the replaced or repaired item. Any parts of the Goods replaced during repairs or any product replaced remain the property of Verbatim.
- In the event of the Goods being replaced during the Warranty Period, the warranty on the replacement Goods will expire on the same date as the Warranty Period of the original Goods they are replacing.
D. Applicable Date/Commencement of Warranty
This warranty commences from the date of purchase from the point of purchase
from Verbatim. The details of the point of purchase, as well as all contact
information for warranty claims and queries, are detailed below:
Contact Verbatim Australia Ply Ltd.
Address Unit 6,450 Princes Highway, Noble Park, VIC 3174
Phone +61 (03) 9790 8999
Fax +61 (03) 9790 8911
Email
Lighting.orders@verbatim.com.au
E. Claim Process The customer claim process is as follows :
- The customer can lodge a claim through the wholesaler from where goods were purchased.
- The wholesaler/customer must complete the online Warranty Claim Request via the lumexlighting.com.au website.
- If accepted as a valid claim within the terms as described in this document, Lumex will provide an equivalent replacement product.
- If goods are to be returned, Lumex will arrange the pickup and return of faulty goods to our warehouse through the wholesaler for further investigation.
- If the claim is rejected, the customer will be provided with a full explanation and if requested the goods will be returned.
IMPORTANT
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to
be of acceptable quality and the failure does not amount to a major failure.
CUSTOMER SERVICE
+61 (03) 9790 8999
verbatimlighting.com.au
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>