LED Lighting MSF Series MaxLite LED Slim Flood Fixtures Instruction Manual

June 9, 2024
LED Lighting

LED Lighting MSF Series MaxLite LED Slim Flood Fixtures Instruction

Manual

MaxLite LED Slim Flood Fixtures (15W-140W)

General Safety Information

  • To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
  • Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.
  • Commercial installation, service and maintenance of luminaires should be performed by a qualified licensed electrician.
  • For Residential installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
  • DO NOT INSTALL DAMAGED PRODUCT!
  • This fixture is intended to be connected to a properly installed and grounded UL listed junction box

WARNING:

  • Risk of Fire – Supply conductors (power wires) connecting the fixture must be rated min. 75°C Supply Conductors. If uncertain consult an electrician.
  • Risk of fire or electric shock. installation requires knowledge of luminaires electrical systems.
  • Risk of Fire/Electric Shock – If not qualified, do not attempt installation. Contact a qualified electrician.
  • Do not use in high humidity conditions.
  • Keep away from flammable and explosive environment.
  • Don’t cover the fixture with insulation liner or similar material.
  • Don’t install where fixture is loose or only partially supported.
  • Don’t impact or exert pressure on the fixture surface face or rear, as damage may occur

CAUTION:

  • For your safety read and understand instructions completely before starting installation.
  • To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
  • Before attempting installation, check your local electrical code, as itsets the wiring standards for your locality.

NOTES:

  • If luminaire (fixture) is to be switched from a wall switch, make sure black power supply wire is connected to the switch. DO NOT connect the white supply wire to the switch.
  • Make certain no bare wires are exposed outside the wire nut connectors.
  • Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

Model:
MSF Series

Operating Instructions

MaxLite LED Slim Flood Fixtures (15W-140W)

General Wiring Diagram

CAUTION: Turn off electrical power at fuse or circuit breaker box before wiring fixture to the power supply

0-10V Dimmable Wiring:
  1. Connect the black fixture wire to the HOT LINE supply wire.
  2. Connect the white fixture wire to the NEUTRAL supply wire.
  3. Connect the green fixture wire to supply ground wire.
  4. Connect the purple fixture wire to the (V+) DIM wire.
  5. Connect the pink fixture wire to the (V-) DIM wire.

Operating Instructions

MaxLite LED Slim Flood Fixtures (15W-140W)

½ NPT Knuckle Mount (15W, 25W, 60W Only)

1.) Remove the luminaire from the packaging.
2.) Connect the AC input wires coming from the mounting bracket to the power supply wires (Fig. 1).

3. Loosen the screw in the center of the mounting bracket and adjust it to the desired angle.
Retighten the screw (Fig. 2).

4.) Insert the ½” threaded nipple into the mounting surface (pole, junction box, etc.). Ensure that it is secure by
either screwing it into the mounting surface or with the supplied nut (Fig. 3).

MaxLite LED Slim Flood Fixtures (15W-140W)

Yoke Mount (All Models)

  1. Remove the luminaire from the packaging.

  2. If there is an existing mounting bracket, other than the yoke mount (i.e. knuckle mount), remove it from the fixture (Fig. 4).

  3. ) Attach the yoke bracket to the fixture using two (2) included bolts (Fig. 5)

  4. Drill two (2) holes into the mounting surface using the yoke mount as a template (Fig. 6).

  5.  Insert expansion bolts (anchor bolts) into the holes drilled in step 4 (Fig. 7).

  6. 6Attach the yoke bracket to the surface, loosen the bolts on both sides of the yoke, and adjust the luminaire to the desired angle. Secure the luminaire in this position by tightening the bolts on both sides of the yoke (Fig. 8).

  7.  Connect the AC input wires coming from the mounting bracket to the power supply wires (Fig. 9)

MaxLite LED Slim Flood Fixtures (15W-140W)

Slipfitter Mount (105W, 140W Only)
  1. Remove the luminaire from the packaging.
  2. Connect the input wires coming out of the mounting bracket to the power supply wires (Fig. 10). Place the wires into the pole and place the mount onto the pole. Secure the mount onto the pole by tightening the locking bolts.
  3. Loosen the screw in the center of the mounting bracket and adjust it to the desired angle. Retighten the screw (Fig. 11).

Installation & Operation – Color Temperature (CCT)/Wattage Adjustment &

PC Controller

  1. Remove the metal and plastic KO plugs from the top of the fixture (Fig. 12)

  2. ) Replace the KO plugs, ensure they are tight to prevent any ingress water. The clear plastic plug should be used on the hole with the photocell controller (Fig. 14).

© Copyright 2022. MaxLite, Inc. All Rights Reserved.
12 York Ave, West Caldwell, NJ 07006 Tel: 800-555-5629 Fax: 973-244-7333 Email: info@maxlite.com

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

LED Lighting User Manuals

Related Manuals