NET LED LIGHTING NET-51-11-XX LED Cambridge Linear Instruction Manual

NET LED LIGHTING NET-51-11-XX LED Cambridge Linear Instruction Manual

Safety Information

• All electrical work must be undertaken by a qualified contractor to ensure compliance with latest edition BS 7671 and IEE/IET wiring regulations.
• Before installing a LED Cambridge fitting or doing any maintainence, ensure power supply is turned off at the circuit breaker or fuse box.
• This product is designed for permanent connection to fixed wiring; the circuit should be protected with the appropriate MCB of fuse.

Environment
Please Do NOT dispose of electrical items or packaging as unsorted waste, use the recycling facilities provided by your local authorities.

PRODUCT DIMENSIONS

LED CAMBRIDGE LINEAR NET-51-11-XX

KEY DATA

SUPPLY/EARTH CLASS

Installation procedure

Carefully read the installation instructions and ensure the mains supply is isolated before installation. Please follow the safety information overleaf before carrying out any installation. Please retain this leaflet for future reference.

step 1: Carefully remove the fitting from the packaging. Using a flat screwdriver, rotate the retention clip into the open position to release the diffuser.

Step 2: Select the mounting points most suitable for the surface. Mount the fitting onto the mounting surface.

Step 3: For side cable entry, drill out the 20mm cable gland position, then secure the cable with a Cable Gland. For rear cable entry, select one of the three pre-cut cable access holes. Select the colour temperature on the Tri-colour switch.

Step 4a: Connect the input wires according to wiring diagram below.

Setting the wattage: As standard, the Tridonic driver is set to 38W. To operate the Tridonic driver at SOW, remove the 1-0 link wire.

Step 4b: Ensure that the Emergency Test Record is completed.

Step 5: Select the colour temperature on the switch. Close the diffuser, then using a flat screwdriver, rotate the retention clip into the closed position to lock the diffuser.

Safety Information:

The dimming cables should be run seperately from the connections and mains cables to ensure good EMC conditions.

Wiring the plug-in terminal:

• Use solid wire or stranded wire with the correct cross-section
• Strip off correct length of insulation; you may need to twist the tool slightly
• If stranded wire is used: push onto the terminal from above to be able to insert the wire
• Insert the bare end into the terminal

Detaching the plug-in terminal:

• Push onto the terminal from above to release the wire
• Pull out the wire at the front

Mains supply wires
Stranded with or solid wire from 0.5 to 2.5mm2 may be used for wiring.

For more information regarding driver settings/options, please access the QR code below:

DALI
Description:
DALI (Digital Addressable Lighting Interface) is an interface protocol for digital communication between electronic lighting equipment.

DALI offers a lot of possibilities:

• DALI line: 64 LED Driver can be grouped to a line
• DALI groups: Every LED Driver can be attributed into 16 groups
• Addressability: All LED Driver are individually addressable
• Grouping: Possible without complicated rewiring
• Programmability: Individual programmability makes it possible to use functions which transcend the DALI standard
• Monitoring: Easily possible thanksto status feedback
• Wiring: Simple wiring with five pole standard cables and a cable length of max. 300 metres
• Wiring: Polarity-free control lines can be used for mains and control lines
• Wiring: Multiple wiring possibilities (star, series and mixed wiring)
• Unaffected by interruptions: All luminaires receive the same, unaffected digital signal and dimming level – Similar light level from first to last luminaire.

Technical data of a DALI line:

• DALI voltage: 9.W – 22.4V
• Maximum DALI system current: max. 250mA
• Data transfer rate: 1200 Baud
• Maximum line length: up to 300m (for 1.5mm2)

switchDlM/Push
Description:
With the switchDlM function it is possible to use the mains voltage as a control signal.
The phase of a standard mains voltage push button is connected to the terminal marked DA/L and the neutral conductor is connected to the terminal marked DA/N.

Using the function is easy and convenient:

• A short press (50-600 ms) switches the device on or off
• A long press (>600 ms) fades the connected operating device alternately up and down (between 1 and 100%)

The device has a switchDlM memory function. This is used, among other things, for storing the last dimming value in the event of interruptions in the power supply. When power returns, the LED is automatically restored to its previous operating state and dimmed to the last value.

Glow switches are not approved for controlling switchDlM. Glow switches may cause the LED Driver to sponaneously switch on or off or make sudden changes in the dimming value.

A maximum number of 25 operating devices per switchDlM system should not be exceeded. If you have more devices please use DALI or DSI.

DSI
Description:
DSI (Digital Serial Interface) enables DS! control gear to be controlled. The DSI line can be wired seperately via a two-core cable or together with the mains cable in a five-core cable. Communication is not impaired by the mains cable. In contrast to DALI, there is no individual addressing of the ballasts with DSI.

DSI offers a series of benefits:

• Expansion options via submodules, for example in combination with daylight control or additional switch modules
• Wiring: Simple wiring with five standard cables and line length of up to 250metres
• Wiring: Polarity-free control lines can be used for mains and control lines
• Wiring: Multiple wiring possibilities (star, series and mixed wiring)
• Unaffected by electrical interference: Uniform light level from the first to the last light source
• Reverse polarity protected connection: can be connected with any polarity.

Important Warranty Information

The LED Cambridge fitting has a 3 year warranty, which can be extended free of charge to 5 years by registering online via the website address below. The registrant must provide the product part number and date of manufacture, which can be found on the label attached to the luminaire housing.

NET LED Ltd.
Buckingway Business Park
300 Anderson Road
Cambridge
CB24 4UQ
sales:a:netled.co.uk
www.netled.co.uk

Technical Helpline: 01223 851505
Email: support:anetled.co.uk

www.netled.co.uk/downloads

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>