Super Lighting LED V1-L Single Color LED Controller Instructions
- June 6, 2024
- Super Lighting LED
Table of Contents
- Super Lighting LED V1-L Single Color LED Controller
- Single Color LED Controller
- Features
- Technical Parameters (Common Data)
- Mechanical Structures and InstallationsMechanical Structures and
- Wiring Diagram
- Match Remote Control (two match ways)
- Application notes
- Push Dim Function
- Profession version V1-L/P DIP switch setting
- Documents / Resources
Super Lighting LED V1-L Single Color LED Controller
Single Color LED Controller
The standard version is single channel constant voltage RF controller with push-dim, and output current up to 15A. The professional version has standard function, in addition to has 3 bit DIP switch to set output PWM frequency and dimming curve.
Features
- 4096 levels 0-100% dimming smoothly without any flash.
- Match with Skydance’s 2.4G single zone or multiple zone dimming remote control.
- One RF controller accept up to 10 remote control.
- Auto-transmitting function: Controller automatically transmit signal to another controller with 30m control distance.
- Synchronize on multiple number of controllers.
- Connect with external push switch to achieve on/off and 0-100% dimming function. Additional features for professional version V1-L/P: Logarithmic or linear dimming curve selectable.
- PWM frequency 250Hz, 500Hz, 2kHz or 8kHz selectable.
Technical Parameters (Common Data)
Input and Output
Input voltage| 12-24VDC
Input current| 15.5A
Output voltage| 12-24VDC
Output current| 1CH,15A
Output power
| 180W/360W (12V/24V)
Output type| Constant voltage
Dimming data
Input signal| RF 2.4GHz + Push Dim
Control distance| 30m
Dimming level| 4096 levels
Dimming range| 0 -100%
Safety and EMC
EMC standard (EMC)| EN301 489,EN 62479
Safety standard(LVD)| EN60950
Radio Equipment(RED)| EN300 328
Certification| CE,EMC,LVD,RED
Environment
Operation temperature| Ta: -30 OC ~ +55 OC
Case temperature (Max.)| Tc: +85OC
IP rating| IP20
Warranty and Protection
Warranty| 2 years
Protection| Reverse Polarity
Mechanical Structures and InstallationsMechanical Structures and
Installations
Wiring Diagram
- Match with dimming remote
- Connect with push switch
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match
Short press match key, immediately press on/off key (single zone remote) or zone key (multiple zone remote) of the remote.
Delete
Press and hold match key for 5s to delete all match, The light blinks 5 times means all matched remotes were deleted.
Application notes
- All the receivers in the same zone.
Auto-transmitting: One receiver can transmit the signals from the remote to another receiver within 30m, as long as there is a receiver within 30m, the remote control distance can be limitless. Auto-synchronization: Multiple receivers within 30m distance can work synchronously when they are controlled by the same remote. Receiver placement may offer up to 30m communication distance. Metals and other metal materials will reduce the range. Strong signal sources such as WiFi routers and microwave ovens will affect the range. We recommend for indoor applications that receiver placements should be no further apart than15m.
- Each receiver(one or more) in a different zone, like zone 1, 2, 3 or 4.
Push Dim Function
Theprovided Push-Dim interface allows fora simple dimming method using commercially available non-latching (momentary) wallswitchs.
-
Short press
Turn on or off light. -
Longpress (1-6s)
Press and hold to step-less dimming, With every other long press, the light level goesto the opposite direction. -
Dimming memory
Light returns to the previous dimming level when switched off andon again, even at power failure. -
Synchronization
If more than one controller are connected to the same push switch, do a long press for morethan 10s, then the system is synchronized and all lights in the group dim up to 100%. This meansthere is no needforany additional synchrony wire in larger installations. We recommend the number of controllers connected to a push switch doesnot exceed 25 pieces, The maximum length of the wires from push to controller should be no more than20 meters.
Profession version V1-L/P DIP switch setting
PWM frequency setting
We can select four PWM frequency: 250Hz, 500Hz, 2kHz or 8kHz. Higher PWM frequency, will cause lower output current, higher power noise, but more suitable for camera(No flickers for video).
Dimming curvesetting
Documents / Resources
|
Super Lighting LED V1-L Single Color LED
Controller
[pdf] Instructions
V1-L, Single Color LED Controller, V1-L Single Color LED Controller, V1-L P
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>