SWAN Flebi Folding Electric Bicycles User Manual
- June 12, 2024
- Swan
Table of Contents
Flyby Folding Electric Bicycles
User Manual
Unpacking & assembly Box contents
The assembly of your Flyby Swan 2022 is very easy and fast!
– Take your Swan 2022 out of the box
– Remove the protections
– Unfold the bike
– Enter the handlebar assembly
– Place the seat post in the frame
– Check the box contents:
– Flebi Swan 2022 bike with integrated battery in the frame
– Battery charger
To install the set formed by the handlebar and the telescopic post that allows
you to adjust the height, you have to insert it into the stem before placing
it in its natural position, following the guides that you will find.
Check that the cables come down clean and remember to tighten the closing key
firmly.
Packed in original box
If you have to repack your bike in its original box to send it to the Flebi
technical service, we recommend that you follow the steps below:
- Cover the parts with protections
- Remove the seat post
- Remove the handlebar assembly
- Fold the bike (see 13)
- Put it in the box
- Place the cork fixing the front wheel
- Rest the pedal on a protection
- Put the lever of the front folding inwards
- Insert the rest of the accessories and seal the box
Start up
Handlebar adjustment
You can adjust the height of the handlebar to accommodate your height.
To do this, open the telescopic lock and place the seat post in the desired
position, taking care not to exceed the safety mark. Then press the clasp
firmly so that it does not move.
You can also use this same adjustment to correct slight deviations in the
direction of the bike. Open the clasp, turn the handlebar left or right
looking for the correct one alignment, and retighten the closing.
You can also adjust the height of the saddle to perfectly adapt it to your
height. To adjust the hardness you must tighten the thread according to your
tastes. Check that it is not too loose or the seaport will move. 
To modify the angle of the seat, you can use a number 13 wrench to decide the
inclination of the seat. Remember to tighten it well.
Brake adjustment
If you need to adjust the brake calipers on your 2022 Flebi Swan, you have
two types of adjustment: for braking force and alignment.
To adjust the force, the pickup on the outer face is adjusted by tensioning
the cable. For the inner face, you must access from the opposite side to bring
the pickup closer.
The ideal is to do it little by little, to test if it brakes cleanly.
Tire inflation
To check the amount of air in the tires, remember that the 2022 Swan has
between 2.8 and 4.6 bar of pressure, so it is convenient to use an inflator
with a pressure gauge.
The pressure will vary depending on the firmness of the ground on which you roll.
Electrical operation
Battery recharge
The Swan 2022’s battery is inside the frame but can be removed from the frame
for convenient charging.
The charging point is located in the upper part of the frame, under a rubber
cover that must be removed to access the connector.
The charger’s led light will turn red, indicating that it is charging, until it is fully charged (about 4 hours), which will turn green, indicating that you can now disconnect.
Display Velux micro Ogled DM03
The micro Ogled display is activated by long pressing the top button.
With the front buttons we can raise assistance to level 5 or lower it to 0,
where we will not have assistance per. To turn on the bike, you must long
press the “up assistance” button.
Remember that the more level of assistance you have selected, there will be more power and more consumption of the battery.
Display – errors
| Código de error — | Description | Action recommended |
|---|
“4”
| Speed throttle does not return to position zero (remains in the high position| Check if the throttle turned again
“5”
| Throttle failure| Check throttle
“7”
| Overvoltage protection| Check battery voltage
“8”
| Motor halt signal wire failure| Check engine
“9”
| Motor phase cable failure| Check engine
“11”
| Engine temperature sensor failure| Check controller
“12”
| Current sensor failure| Check controller
“13”
| Battery temperature failure| Check battery
“14”
| The controller temperature is too high and reach protection point| Check engine
“21”
| Speed sensor failure| Check the installation position of the sensor speed
“22”
| BMS communication failure — replace battery| BMS communication failure Replace battery
“30”
| Communication failure| Check connector to controller
Folding & Unfolding
Unfolding the bike
The steps to deploy your Flebi Swan 2022 are very simple:
- Raise the bike and unfold the frame, tighten the central lock and set the safety
- Deploy the pedals (see 16)
- Raise the stem of the handlebar, close the folding lever and insert the safety (see 17)
Folding the bike
The steps to fold your Flebi Swan 2022 are very simple:
- We lower the handlebar
- Releases the mechanism of the central lock of the frame (see 15)
- Fold the pedals (see 16)
- Open the frame and bring it to the folded position
- The bike rests on the bottom bracket
Opening and closing the box
To open or close the box, you just have to remove the safety in the central
part in case of opening it and put it in case of closing it.
Folding & unfolding of the pedals
Install the pedals of your Flebi Swan 2022 very easily with this tutorial.
To fold or unfold each pedal you must push the control out and at the same
time fold the pedal in (folded) or out (deployed) until you notice the
blockage.
Folding mechanism of the handlebar
First of all make sure that the cables are not tangled or too tight due to the
set handlebar height.
You can adjust the height and inclination of the handlebar. The bike has an
indicator on the inside of the handlebar to know the maximum height. In
addition, you can tilt the levers and grips for your greatest comfort. 
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>