SuperLightingLED 204 Ethernet-SPI-DMX Pixel Light Controller User Manual

: June 9, 2024
: SuperLightingLED

Table of Contents

Brief Introduction
Specifications
Basic Features
Safety warnings
Dimensions
Operating Instructions
Conjunction Diagram
After-Sales
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Ethernet-SPI/DMX Pixel light controller
User Manual

( Please read through this manual carefully before use）
Update Time :2019 .11.1

Brief Introduction

This Ethernet-SPI/DMX pixel light controller is dedicated to converting the Ethernet signal into SPI pixel signal, which is designed for large project with high-density pixel light, such as matrixpanel lights, construction’s contour lamp, etc. Besides converting Ethernet-based control protocols into various LED driving IC signal, it also outputs DMX512 signal at the same time, convenient forthe connection of different types of led lamp, and to achieve the unified control of all kinds of ledlamp in the same project.

Specifications

Model #	204	216
Working Voltage	DC5-DC24V	DC5-DC24V
Output Current	7A X 4CH (Built-in 7. 5A fuse )	3A X 16CH (Built-in 5A fuse )
Input Ethernet control protocol	ArtNet, sACN(E1.31)	ArtNet, sACN(E1.31)
Output Control IC

Basic Features

With LCD display and built-in WEB SERVER setting interface, easy operation.
Support Ethernet DMX protocol ArtNet, sACN(E1.31), can be expanded to other protocols.
Multi SPI (TTL) signal output.
Output DMX512 signal at the same time, convenient for the connection of different types led lamp.
Support various LED driving IC,flexible control.
Support online firmware upgrade.
Adopt DIP plug-in design for the easily-worn parts, Users can repair the damage caused by wrong wiring or short circuit.
Built-in test mode, using a network interface with indicator light, work status is clear when at a glance.

Safety warnings

Please don’t install this controller in lightening, intense magnetic and high-voltage fields.
To reduce the risk of component damage and fire caused by short circuit, make sure correct connection.
Always be sure to mount this unit in an area that will allow proper ventilation to ensure a fitting temperature.
Check if the voltage and power adapter suit the controller.
Don’t connect cables with power on, make sure a correct connection and no short circuit checked with instrument before power on.
Please don’t open controller cover and operate if problems occur.
The manual is only suitable for this model; any update is subject to change without prior notice.

Dimensions

Operating Instructions

204 216 Instruction of interface and ports:

Notice: The controller should connect with two power supplies.
The 2st power supply support SPI 1-8, the 1nd power supply support SPI 9-16, (The two power input can share the same unit power supply when the power is sufficient).

Wiring instructions of SPI output port：

To output LPD6803/LPD8806/P9813/WS2801 controlling signal , it required at least three lines :

DATA	6803/8806/9813/2801 DATA
CLK	6803/8806/9813/2801 CLK
GND	GND，connect with the chip GND

To output WS2811/ TLS3001/TM1814/SK6812 controlling signal, it required at least two lines：

DATA	WS2811/ TLS3001 DATA
GND	GND，connect with the chip GND

Connect the Lamps positive supply to the + of the SPI output ports.
1. Key Description

Button	Short Press Function	Long Press Function
MODE	Switch setting parameter type	Enter test exit mode
SETUP	Enter and switch setup
+	Increase current set value	Increase current set value rapidly
–	Decrease current set value	Decrease current set value rapidly
Enter	Confirm and enter into next set value

2. Operating and setting instructions
Ethernet-SPI/DMX pixel light controller with two working models.
Respectively：normal working mode and test mode.

(1) Normal working mode
Normal mode is based on Ethernet transferring Artnet protocol into a control signal which can be received by various pixel lamps; Connecting the lamps, plugging the network cable, after checking, power on. The controller will enter into the network detection.

UNABLE TO
OPERATE …

After detecting without problems, the controller will enter into normal working mode and show the IP address, IP address has static and dynamic allocation. STAT for static allocation, DHCP for dynamic allocation, the controller default IP address is static.

IP ADDRESS – STAT
192.168.0.50

This controller also comes with key lock function, no operation after 30 seconds, the system enters the lock state, then LCD shows.

PRESS AND HOLD M
BUTTON TO UNLOCK

Long press “MODE” to unlock, unlocked before next operation.
(2) Parameter Setting
In normal working mode, press “MODE” to switch parameter setting type, “SETUP” to enter the setup, then press “ENTER” to get back to previous level.

NO.	Setting	LCD display
1	System setup	1SYSTEM SETUP
IP static and dynamic selection	DHCP-YES
PRESS OK TO SAVE	YES: Dynamic IP NO: Static IP(Default )
IP Address	STTC IP 192.16A8.I0.50	Static IP address (Default) : 192.168.0.50
Subnet Mask	SUBNET MASK255. 255. 255.0	(Default) 255.255.255.0
IC type	PIXEL PROTOCOL
2811	-2811(Default)-8904-6812-2904-1814-1914″ -5603-98 1 2″”APA 102-2812-98 1

3-300 1″ -8806-6803-2801-
RGB Sequence| LEO RGB SEC)
RGB| -RGB(Default)” -RBG- -CRS’ -GBR- -BRG” MGR’ -RCM” -RGWB”RBGW” -RBWG’ 6RWGB” -RWBG” ‘GRBW” -GRWB” -GBRW -GBWR” -GWRIr GWBR” -BRGW” -BRWG” -BGRW’ -BGWR” -BWRG ‘BWGR” -WRGB” -WRBG*-WGRIK -WGBR4 -WBRG” -WBGR’
Si gnal configuration| SIGNAL CONFIG
sACN(E1 31)| Protocol selection: -sACN(E1.3.1)(Default)”, -ArtNet”
LCD background dormancy time selection| ALWAYS Ught ALWAYS ON| “ALWAYS ON” -1 MINUTE” “5 MINUTES’ 10 MINUTES’
2| Channel 1 setup| 20uT1 SETUP| 204:OUT1-4 SETUP 216:OUT1-16 SETUP
Universe setup| 2OUT1 START UNIVERSE 256| Universe settings range: sACN(E1.31) Protocol:1-65536 ArtNet Protocol: 1-256
| DMX Channel| OUT I START
CHANNEL 512| DMX channel range : 1-512 The default value : 1
---|---|---|---
Pixel| OUT1 NUM
PIXELS: 680| 204 : Pixel range : 0-680 The default value : 680
216: Pixel range : 0-340 The default value : 340
Null pixels| OUT1 NULL PIXELS: 680| 204 : Null pixel range : 0-680 The default value : 0
216 : Null pixel range : 0-340 The default value : 0
Zig zag pixels| OUT1 ZIG ZAG: 680| 204: Zig zag pixel range : 0-680 The default value : 0
216: Zig zag pixel range : 0-340 The default value : 0
Reverse Control| OUT1
REVERSED:YES| YES: Reverse control
NO (Default): Not reverse control
3| Channel 2 setup| 3OUT2 SETUP| Same to channel 1
4| Channel 3 setup| 40073 SETUP| Same to channel 1
5| Channel 4 setup| 5OUT4 SETUP| Same to channel 1
6| DMX512 channel setup| 6DMX512 OUTPUT| 204: One DMX512 channel 216: Two DMX512 channels
DMX512 output selection| DMX512 OUTPUT
YES| YES(Default): Output NO: Not output
DMX512 universe setup| DMX512
UNIVERSE:255| DMX512 Domain settings range : 1-256
7| Load default| 7LOAD DEFAULT|
Confirm to load default| LOAD DEFAULT
YOU SURE?|
8| About| 8ABOUT|
Model| Ethernet.SPI4 ID04000012|

Control ICs type:

IC Type	Compatible ICs	Type
2811	TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912 UCS2903,
UCS2909, UCS2912, WS2811, WS2812B, SM16703P , GS8206 etc	RGB
2812	TM1803, TM1804, TM1809, TM1812, UCS1903, UCS1909, UCS1912 UCS2903,

(3) Test mode
Long press “MODE” to enter the test mode, press it again to exit, after entering the test mode, press “+” “-” to switch the mode and “SETUP” to set the parameter of the current mode. After enter into test mode, the LCD will show operation tips, as below:

PRESS AND HOLD M
FOR NORMAL MODE
PRESS “+”OR“-”
TO CHOOSE MODE

NO.	Built-in sequences	NO.	Built-in sequences
1	Solid color: Black(Off)	13	Blue chase with trail
2	Solid color: Red	14	Rainbow chase – 7 Colors
3	Solid color: Green	15	Green chasing Red, chasing Black
4	Solid color: Blue	16	Red chasing Green, chasing Black
5	Solid color: Yellow	17	Red chasing White, chasing Blue
6	Solid color: Purple	18	Orange chasing Purple, chasing Black
7	Solid color: CYAN	19	Purple chasing Orange, chasing Black
8	Solid color: White	20	Random twinkle: White over red background
9	RGB CHANG	21	Random twinkle: White over blue background
10	full COLOR CHANGE	22	Random twinkle: White over green background
11	Red chase with trail	23	Random twinkle: White over purple, background
12	Green chase with trail	24	Random twinkle: White over orange background

3. WEB setting, Firmware upgrading online.
In addition to set parameters by buttons, you can also set it through the Web browser of computer. The parameter settings between the two are the same.
WEB operation instructions:
Open the web browser of the computer, which is in the same LAN with the controller, input the IP address (such as the default IP: 192.168.0.50), and press “Enter” to browse the controller’s built-in website, as shown below:

Enter the default password：12345，Click to enter the parameter setting page.
The users can set the parameter and upgrade the firmware on website.

Upgrade the firmware online:
To find the column “Firmware Update”on website (as below)

Then click ， to enter the firmware update page(as below), click , then choose the BIN file you need to upgrade, then click enter into firmware updating page, After upgrade, the website will auto matically back to the login screen. Choose file Update

Conjunction Diagram

After-Sales

From the day you purchase our products within 3 years, if being used properly in accordance with the instruction, and quality problems occur, we provide free repair or replacement services except the following cases:

Any defects caused by wrong operations.
Any damages caused by inappropriate power supply or abnormal voltage.
Any damages caused by unauthorized removal, maintenance, modifying circuit, incorrect connections and replacing chips.
Any damages due to transportation, breaking, flooded water after the purchase.
Any damages caused by earthquake, fire, flood, lightning strike etc force majeure of natural disasters.
Any damages caused by negligence, inappropriate storing at high temperature and humidity environment or near harmful chemical.