Saxby Lighting Kit 51918 Aqualine 12V Premium Display Tape Instructions
- June 12, 2024
- saxby lighting
Table of Contents
Aqualine Kit
51918
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
The power supply is Double Insulated and does not require connection to an
Earth circuit.
The LED strips are Safety Extra Low Voltage and must not be earthed.
Please read these instructions carefully before commencing any work.
This unit must be fitted by a competent and qualified electrician.
Install in accordance with IEE Wiring regulations and current Building
Regulations.
This system operates at Safety Extra Low Voltage (12V), via a LED driver.
Never connect the light fittings directly to the mains without using a LED
driver.
Ensure that the supplied LED driver is used.
The mains plug must be situated indoors (e.g. house, garage, shed) in order to
protect it from the elements.
Do not exceed the LED driver load. LED drivers may require @ minimum load to
operate.
Always disconnect the LED driver from the mains.
when installing or maintaining this system.
This system contains non-replaceable parts and cannot be serviced. If damage
occurs the part should be scrapped.
This product is rated at IP44.
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
Battery care: Do not recharge non-rechargeable batteries. Do not mix old and
new batteries or batteries of different types.. Do not use rechargeable
batteries.
Always remove exhausted batteries from the remote control. Always insert the
battery with the correct polarity. Do not short circuit the supply terminals.
This product is suitable for use by adults only.
Specification
Dimensions : 10mm wide, 3mm high x 5000mm long
Voltage : 220-240V~ 50Hz
LED Voltage : 12vd.c.
Specification
The Kit should contain:
- 1 xin-ling driver with UK 3 Pin Plug (0.5m mains cablw and 1.5m Output cable)
- 1 x RGB Remote and Programmable Remote Control
- 1 x 5000mm strip
Layout
- This is a self contained kit and cannot be extended.
- The Aqualine LED’s are mounted on a sticky tape which can be stuck to most surfaces.
- The Aqualine LED’s can be shortened to a minimum of 100mm or multiples of 100mm.
- Plan the desired layout of this fitting carefully, ensuring the cables will reach the distance between the LED driver and the Aqualine LED position.
- Avoid locating any cables in positions that would cause a hazard. Position cables and Aqualine LED’s away from areas where they may be at risk from being cut, frapped or damaged.
- Cables in walls must be protected using suitable conduit or plastic trunking.
- This product is IP44 rated. It should not be used in very wet areas.
Basic Installation
-
Position the plug, remote control sensor and in-line LED driver next to the indoor mains outlet socket that the system will connect to. Do not plug-in at this stage.
-
After deciding the layout of the Aqualine strip, ensure that the cable can connect when in the desired position.
-
It is possible for the Aqualine strip to be shortened.
This can be done in multiples of 100mm. Look for the line on the strip with four copper pads, as shown below. -
Cut using a sharp pair of scissors. Do not cut anywhere else on the strip as this may cause the Aqualine strip to stop working.
Seal the end with a small amount of silicone sealant. -
Connect the LED driver connector to the connector on the Aqualine strip. Ensure that the polarity is correct.
Commissioning
- Check all connections are tight. Plug in and test.
- Peel the adhesive backing off of the strips and stick in place.
- Your srips are now ready for use.
Operating the remote control and replacing the battery
- There are various colour mode variations as shown below.
- To replace the battery, release the compartment from inside the remote control by pushing the lever at the bottom left of the compartment. Pull the battery housing out and replace the exhausted battery with a new one – make sure the polarity is correct. Then slide the compartment back inside the remote control.
- Heed the battery care warnings overleat.
Recycling advice
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your Local Authority or
retailer for recycling advice.
Safety information
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
UK Manufacturer: BH17 7BY
EU Manufacturer: Biliant AG,
Brlantstasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>