saxby lighting 103022 Batten Plug-In Pir Sensor Instruction Manual

: October 30, 2023
: saxby lighting

Table of Contents

103022 Batten Plug-In Pir Sensor
INTRODUCTION
SPECIFICATIONS
DETECTION DIAGRAM
INSTALLATION
IP LUMINAIRE FITTING
SETTING BY REMOTE CONTROL
WIRING DIAGRAMS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

BATTEN PLUG-IN PIR SENSOR
Instruction manual
103022
103023 saxby lighting 103022 Batten Plug-In Pir
Sensor

103022 Batten Plug-In Pir Sensor

Thank you for purchasing this light ﬁtting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference. saxby
lighting 103022 Batten Plug-In Pir Sensor - fig 1

INTRODUCTION

The miniature PIR (passive infrared) presence detector provides automatic control of lighting loads. It is specifically designed for mounting onto a batten style luminaire.
The detector will switch incandescent, fluorescent, compact fluorescent and LED lighting.
The unit detects movement using a PIR sensor and turns the load on. When an area is no longer occupied the load will switch off after a 10 minute time out period.
A selection of fixing washers are supplied to aid fixing to a variety of luminaires.

SPECIFICATIONS

Dimensions Supply Voltage Frequency Maximum Switching Load| See diagrams opposite. 220-240VAC 50/60Hz 2 Amps fluorescent and incandescent lighting. 2 Amps compact fluorescent lighting. 2 Amps low energy lighting. 2 Amps low voltage lighting (switch primary of transformer). Switch SON lighting loads via a contactor.| Power consumption Cable specification
Temperature Humidity Material Type IP rating| On 799mW, Off 807mW 1m 1/1.13 solid core cable 105°C -10°C to 35°C 5 to 95% non-condensing Flame retardant ABS/PC Class 2 IP65
---|---|---|---

DETECTION DIAGRAM

saxby lighting 103022 Batten Plug-In Pir Sensor - fig
2 Note: illustration shows an average of the walk across and walk towards figures below.
Walk across

Height	Range Diameter
7m	16m
2.8m	9m

Walk towards

Height	Range Diameter
7m	10m
2.8m	5m

INSTALLATION

Do not grip unit at the lens end. Hold the square body near the threaded end when installing and tightening the nut. Care must be taken to prevent damage to the lens and surrounding IP seal.
Components

| Part| Quantity Supplied
---|---|---
| Silicone washer| 2
| 5° washer| 1
| 5° spacer| 1
| M20 nut| 1

Mounting hole without key Mounting hole with key Note. Key to be at top of sensor.

IP LUMINAIRE FITTING

Note. Use the 5° spacers where the luminaire housing has a draft angle.
Important
Ensure that the Silicone washer and/or the IP spacer are used to ensure IP rating. saxby lighting 103022 Batten Plug-In Pir Sensor - fig
10

SETTING BY REMOTE CONTROL

| | ON=Menual onsfter 6 hours turns to -AtfrOlnode
OFF=manual off, after 6 hours turns to “AUTO”mode| | The sensor starts to work automatically,and all
paraments back the latest setting before TEST mode, onloff mode,and reset mode.
---|---|---|---|---
| Time setting| | Reset
-Resetting of all functions
| Range setting| | In lest mode.hold time is only 2s. and stand-by time and daylight sensor are disable.
Quit Test Mode,Press Auto button
| Preselected light values
-10 to 2000 Lux: Recommendation: rooms with daylight 500 Lux, without daylight 2000 Lux| | Permanent tamper protection
– Permanent inhibition or the detec -tor; only ON- and OFF function on the remote control possible.
on=permanent on of apermanent off
Unlock permanent tamper prate:ion
| The latest surrounding lux value leamed,and Is set as the daylight threshold.| |

Operation tips:
A:Set 10SEC,6M,100LUX as a exmple

We push you set TIME, LUX, RANGE,it must enter in Auto mode first.
Push ,the sensor off,sensor led will flash 3 times as confirmation.
Push , the sensor off,sensor led will flash 3 times as confirmation.
Push , the sensor off,sensor led will flash 3 times as confirmation.

B:ON MODE
If you push ON,the sensor on,and will enter in auto mode after 6 hours when there are no motions.
C:OFF MODE
If you push off,the sensor on,and will enter in auto mode after 6 hours when there are no motions.
NOTE: QUIT ON/OFF Mode,Please Auto Button.
D: LOCK(UNLOCK)
If you push , the remote control is lock,only ON and OFF function on the remote control possible. In this time,sensor has no motion function,only permanent on or permanent off. Push the ,unlock the remote control.

There is interval 4 seconds after the sensor stop work,during the 4 seconds,the sensor can’t work. After 4seconds, thEs ensor start work.

WIRING DIAGRAMS

INSTALLATION
The product is designed to be mounted directly to the outside of a luminaire. The detector should be sited so that the occupants of the room fall inside the detection pattern (shown opposite), at a recommended ceiling height of 2.8m. Note that the lower the sensor is installed the smaller the detection range will be, subject to the parameters shown on the detection diagram.