GOLDEN LIGHTING 4308-OWM Cohen 2-Light Textured Bronze Clear Glass Panels Hardwired Outdoor Wall Lantern Sconce Instruction Manual
- June 8, 2024
- GOLDEN LIGHTING
Table of Contents
Assembly Instructions: 4308-OWM
Thank You for Choosing Golden Lighting for Your Lighting Needs!
4308-OWM Cohen 2-Light Textured Bronze Clear Glass Panels Hardwired
Outdoor Wall Lantern Sconce
Pendants & Linear Pendants Above a Kitchen Island
Center a linear pendant over the island. If hanging pendants, use one pendant
for every 24″ of island. Fixtures should hang at least 30″ above the
countertop.
Pendants & Chandeliers Above a Dining Room Table
Fixtures should stay at least 30″ above the table. Use a fixture that is 12″
narrower than the width of the table.
Pendants and Chandeliers in Open Areas
The bottom should hang at least 7.5 feet from the floor.
Allow clearance for any opening doors.
We appreciate your business and hope you love your new light!
Great lighting can add value and enhance the look of your home. To ensure the
best lighting in your space, remember to layer your lighting. This ensures
that your space will have both task and ambient lighting. Coordinating
fixtures like sconces, flush mounts, and pendants can help you meet your
layered lighting needs and reinforce your desired aesthetic. Install the
lights with dimmers that allow you to control the level of light output at any
given moment.
Get function and style! Browse our site for coordinating lights and expert
lighting advice. To help create the perfect look, visit
www.GoldenLighting.com.
Love your light and want to show it off?
Follow us, share a picture, and tag us on Social…
How to Identify the Fixture’s Wires
Hot: Smooth, Black, or Transparent with Black Inner Thread
For Customer Service, contact the place of purchase to arrange for replacement parts.
IMPORTANT:
- All installation work should be done by accredited professional.
- Shut off power supply at fuse or circuit breaker!
- Use only the specified bulbs. Do not exceed the maximum wattage!
Assembly Instructions:
PREPARING FOR INSTALLATION
Carefully remove the new fixture from the carton as well as the yellow bag
that holds all of the parts. See the important notes above. Shut off power at
the circuit breaker and remove old fixture from wall, including the old
mounting strap. 1. Take the mounting strap assembly from the parts bag.
Mounting strap (A) contains threaded holes. Two of mounting screws (C) should
be attached to mounting strap (A). You may need to tighten nuts that hold
these screws in place. Pull the house wires through the center of mounting
strap (A). Place mounting strap (A) over the junction box so that mounting
screws (C) are horizontal, and in alignment with the hole locations on the
fixture’s backplate (D). Secure mounting strap (A) to the junction box with
mounting screws (B) and a screwdriver. Tighten the screws securely.
ASSEMBLING THE FIXTURE
(PLEASE NOTE: This fixture may be installed with the accent (1) or without the
accent (2)) TO INSTALL WITH THE ACCENT, REFER TO DIAGRAM (1): 2. Loosen the
screws (M) and remove the lower aluminum cover (L). Remove the nut (H) and
place the accent (G) on the iron part (P) of the lamp body. Secure accent (G)
with nut (H). Insert glass sheets (I) and (J) into the middle of the aluminum
strip (K) of the lamp body. Place the lower aluminum cover (L) on the aluminum
strip (K) and fasten it with screws (M). TO INSTALL WITHOUT THE ACCENT, REFER
TO DIAGRAM (2): 2. Loosen the screws (M) and remove the lower aluminum cover
(L). Insert glass sheets (I) and (J) into the middle of the aluminum strip (K)
of the lamp body. Place the lower aluminum cover (L) on the aluminum strip (K)
and fasten it with screws (M)
CONNECTING THE WIRES
3. Have an assistant support the fixture’s weight while completing the
wiring. Refer to the wiring diagram and attach the fixture’s wires to the
power supply wires from the junction box. Attach the fixture’s wires to the
power supply wires from the junction box. Connect Hot to Hot (transparent wire
with black inner thread, black, or smooth wire) Neutral to Neutral
(transparent wire with white inner thread, white, or ribbed wire), and Ground
to Ground (transparent wire with green inner thread, green wire, or copper).
Twist the ends of the wire pairs together, and then twist on a wire connector.
Make sure all twists are in the same direction. If there is no house ground
wire coming from the junction box, locate ground screw (E) on the mounting
bracket/mounting strap and wrap the fixture’s ground wire around the ground
screw. Use a screwdriver to tighten the top of ground screw (E) onto the wires
and into the mounting bracket/mounting strap. Tuck the wires into the junction
box.
FINISHING THE INSTALLATION
4. Place the fixture’s backplate (D) over mounting screws (C) so that they protrude through the holes in the front of backplate (D). Thread deco nuts (F) onto mounting screws (C). Twist until the backplate of the fixture is snug against the wall. 5. Install light bulbs (not included) in accordance with the
Get help, quick tips, and explore curated content
| @GoldenLighting
---|---
| @GLFixtures
| @GoldenLighting1
| @GoldenLighting
Documents / Resources
|
GOLDEN LIGHTING 4308-OWM Cohen 2-Light Textured Bronze Clear Glass Panels
Hardwired Outdoor Wall Lantern
Sconce
[pdf] Instruction Manual
4308-OWM Cohen 2-Light Textured Bronze Clear Glass Panels Hardwired Outdoor
Wall Lantern Sconce, 4308-OWM, Cohen 2-Light Textured Bronze Clear Glass
Panels Hardwired Outdoor Wall Lantern Sconce, Clear Glass Panels Hardwired
Outdoor Wall Lantern Sconce, Hardwired Outdoor Wall Lantern Sconce, Outdoor
Wall Lantern Sconce, Lantern Sconce, Sconce
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>