WALI GSWM002 Dual Monitor Wall Mount Instruction Manual
- June 8, 2024
- WALI
Table of Contents
GSWM002 Dual Monitor Wall Mount
Instruction Manual
GSWM002 Dual Monitor Wall Mount
WARNING! If you do not understand these directions, or if you have any
doubts about the safety of the installation, please call a qualified
technician. Check carefully to make sure there are no missing or defective
parts. Improper installation may cause damage or serious injury. Do not use
this product for any purpose that is not explicitly specified in this manual.
Do not exceed weight capacity. This product is designed to be installed on
wood stud walls, solid concrete walls or brick walls. Do not mount on drywall
alone. We cannot be liable for damage or injury caused by improper mounting,
incorrect assembly, or inappropriate use.
TIPOVER WARNING
SERIOUS OR FATAL CRUSHING INJURIES CAN OCCUR FROM TIPOVER. TO HELP PREVENT
TIPOVER:
- NEVER ALLOW CHILDREN TO CLIMB, STAND, HANG, OR PLAY ON ANY PART OF MONITOR OR STAND.
- USE TIPOVER RESTRAINT OR ANCHOR STAND TO WALL.
USE OF TIPOVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE RISK OF TIP OVER.
SMALL PARTS- NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
Supplied Parts List
Step 1 Option A Wood Stud
- If installing this product on wood stud, mark the position with Bubble Level & pencil on the wall.
- Drill 3/16″(4.5mm) diameter x 2.2”(55mm) length holes at the marked position.
- Attach the mount to wood stud and tighten using Screw W-A & D5 Washer W-C with a screwdriver.
(Screwdriver not included)
Option B Concrete Wall
- If installing this product on concrete wall, mark the position with Bubble Level & pencil on the concrete wall.
- Drill 3/8″(10mm) diameter x 2.2”(55mm) length holes at the marked position.
- Insert the Anchor W-B into the mounting holes. Attach the mount to concrete wall and tighten using Screw W-A & Washer W-C with a screwdriver. (Screwdriver not included)
Step 2
Fix Cover **C**onto the front of mount part. Step 3
Step 3.1 Select TV Screws
Step 3.2
Attach the VESA Plate B to your TV/Monitor, and thread M4x12 Bolt M-A
or M5x12 Bolt M-B into the mounting holes with D5 Washer M-C , tighten
with Allen Key 5mm D .
Step 4
Detach the Top Screw by threading it counterclockwise.
Step 5
Put the assembled TV/Monitor onto the Arm A and ensure the stability, tighten
the VESA Plate B using Top Screw. Step 6
Press the Arm A on horizontal level as image shown, adjust gas spring
tension to your personal preference using Allen Key 5mm D . Adjust the
tilt tension using Allen Key 5mm D .
- Insert the 5mm Allen Key into the adjusting hole and turn clockwise (-) to reduce gas spring tension, suitable for lighter screens.
- Insert the 5mm Allen Key into the adjusting hole and turn counter-clockwise (+) to increase gas spring tension, suitable for heavier screens.
- Please take note it may take numerous turns for gas spring tension adjustment.
Step 7
Screw out the bolts with Allen Key 5mm D and take off the cable cases.
Step 8
Guide the cables through and put the cable cases back.
Step 9
Manually swivel, tilt, and rotate the monitor for the best viewing angle.
Thank you for choosing us!
We support the technology that brings your home to life.
We offer high quality products, professional customer service, and extensive
technical support.
If you have any questions,please contact us.
1-844-SATTLER (18447288537)
support@walielectric.com
www.walielectric.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>