OPT7 Headlight Restoration Kit Installation Guide

OPT7 Headlight Restoration Kit

COMPONENTS

RESTORATION STEP

• STEP 1
  Remove any dirt, dust or debris from headlight using a provided Alcohol
  Prep Pad and wipe dry with the Large Microfiber Towel G

• STEP 2
  Mask edges using masking tape

• STEP 3
  Attach 1000 Grit Sandpaper to the Hand Sander A

• STEP 4
  Sand the headlight in a smooth uniform side to side motion with overlapping passes. Be captious around edges and be careful to not touch paint. Keep the sandpaper wet by dunking it into a small container with water or spraying water directly onto the sandpaper

• STEP 5
  Sand evenly and with the same pressure as to create a smooth surface but not generate extreme heat irn any particular area of the headlight. Be sure to occasionally clear the headache lens of debris)

• STEP 6
  Remove 1000 Grit Sandpaper and attach the 3000 Grit Sandpaper to the Hand Sander

• STEP 7
  Sand the headlight in a smooth uniform side to side motion with overlapping passes Be cautious around edges and be careful to not touch pains Maintain or keep the sandpaper wet by dirking t into a smell container with water or spraying water directly onto the sandpaper

• STEP 8
  Attach the Buffer Drill Attachment to the drill with the Firm Foam Pad

• STEP 9
  Apply 3 nickel-sized drops of Pad STEP CPK-1 Polish to the Firm Foam Pad

• STEP 10
  Use a slow, back & forth continuous overlapping motion and alter drill speed as needed to treat small area at a time. Heavy pad pressure is not required. Do not use the pads edge

• STEP 11
  Remove Firm Foam Pad and attach the Soft Foam Pad to the drill.

• STEP 12
  Apply 3 nickel-sized drops of CPX-2 Polish to the Soft Foam Pad

• STEP 13
  Use a slow, back & forth continuous overlapping motion and alter drill speed as needed to treat small area at a time.
  Heavy pad pressure is not required. Do not use the pads edge.

• STEP 14
  Clean the headlight lens with an Nichol Prep Pad to remover all CPX product residue, then wipe dean and dry with the fresh side of a microfiber towel.

• STEP 15
  Apply 5-10 drops of the Ceramic-Nu across the headlight. Wait 1-2 minutes for a rainbow-like haze to appear, then use Small Microfiber Towel to wipe away to ensure no haze ramraid

• STEP 16
  Continue working your way across the headlight with overlapping strokes until the entire headlight has been treated.
  Optional: Repeat the coating procedure again for extra protection

• STEP 17
  It is recommended to keep headlight clean a dry while Ceramic-Nu Protection Bond fully for 24 hours

WARNINGS & HAZARDS
Perform in a dry area away from direct sunlight Not intended for use on LCD, navigation screens, plastic convertible top windows, or motorcycle windscreens.

DISCLAIMER

The information in this Material Safety Data Sheet (MSDs) is believed to be correct as of the date issued. OPT7.
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.
User is responsible for determining whether the OPT7, Inc. product is fit for a particular purpose and suitable for user’s method of use or application. Given the variety of factors that can affect the use and application of a OPT7, Inc. product, some of which are uniquely within the user’s knowledge and control, it is essential that
the user evaluate the OPT7, Inc. product to determine whether it is fit for a particular purpose and suitable for user’s method of use or application. OPT7, Inc. provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in
this information, OPT7, Inc. makes no representations as to its completeness or accuracy.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>