rombica Mysound Woody BT-S011 Bluetooth Speaker User Manual

rombica Mysound Woody BT-S011 Bluetooth Speaker

Thank you for purchasing Rombica device. Please read this user manual before the operation and save it for the future

ASSEMBLE STEPS

1. Open the gift box and remove the components from it. Put the speaker
   on the tabletop and the fixing hole upwards. Do not place the device on rough surfaces – it can lead to the coating damage

2. Take one of wooden legs and match it with one fixing hole

3. Rotate it clockwise until tightly fixed

4. Fix another two wooden legs the same way

5. Check that wooden legs are well fixed

6. Put the speaker on the flat surface

GENERAL INFORMATION

1. Power/TWS. Long press – power on/off. Double press – launch TWS mode
2. Pause/Play/Ring
   • Short Press – Pause/Play
   • Quick double press – call back to last caller (Bluetooth mode)
   • Short press during incoming call – receive incoming call (Bluetooth mode)
   • Long press during incoming call – reject incoming call (Bluetooth mode)
3. Button «Vol-» – decreasing volume
4. Button «Vol+» – increasing volume
5. LED indicator No 1
6. Microphone
7. USB Output No 1 for personal devices
8. USB Output No 2 for personal devices
9. LED indicator No 2
10. DC Input for charging built-in battery
11. AUX
12. Reset
13. Wireless Charger (Woody Q and Woody W models only)

SPECIFICATION

• Power: Built-in battery, AC adapter 110-230V, 50-60Hz / 16V, 2A
• Audio channels: 2.0
• Bluetooth solution: ACTS Digital Audio Output
• Bluetooth version: v4.2
• True Wireless Stereo support (except mysound Woody): yes
• Speakers power. 88W (2 x 20W + 4 x 12W)
• Speaker: Midrange© 2.75″ 30 12W x 4, Tweeter© 1.2″ 80 20W x 2
• Radiator: © 3″ x 4
• Frequency: 1 OOHz – 18kHz
• S/N Ratio:   75db
• Separation Ratio: 1 35db
• Battery: 6600mAh / 3.7V (24.42Wh)
• Amplifier IC: Class D Tl TAS5711 DSP
• Handsfree phone call function: yes
• Interfaces: 2 x USB Type-A, AUX, Bluetooth, mic, wireless charging
• Wireless charging power: 5W*
• In the box: speaker, wooden legs, AC adapter, audio cable, user manual
  TECHNICAL CHARACTERISTICS AND APPEARANCE MAY BE CHANGED WITHOUT PRIOR NOTICE

OPERATION OF THE DEVICE

• POWER ON
  Press and hold the power button. Sound notification and turned-on LED indicator N21 will confirm turning on

• POWER OFF
  Press and hold the power button. Sound notification and turned-off LED indicator NQ1 will confirm turning off. The speaker turns off automatically after 1 O minutes of inactivity, such as no Bluetooth connection, no LINE IN signal

• PARING VIA BLUETOOTH

1. Disconnect AUX cable if connected. Turn on speaker
2. Open Bluetooth setting on your smartphone/PC, enable Bluetooth search for new devices. When Bluetooth speaker found, confirm pairing
3. After successful pairing both the Bluetooth speaker and your device, you can control playback by Bluetooth speaker buttons

• TRUE WIRELESS STEREO (except mysound Woody)
  TWS feature allows you to link two speakers together. The first speaker will be the master connected to the Bluetooth device and operate all controls. The second speaker is a linked speaker giving True Wireless Sound.

1. Turn on both table speakers, double click Power/lWS button (1) on one of the two table speakers, both speakers will enter team paring mode, you will hear an specific signal, both blue LED indicator of both table speakers will flash rapidly at the same time. After the team paring, the LED indicator of first speaker (Master) will remain flash slowly, the LED of second speaker (SUB speaker) (linked lWS) will be green. After connecting with phone or other Bluetooth devices, the Master speaker LED will Blue stably, the sub-speaker keep stable Green LED.
2. When speakers are team paired successfully, short press Power/TWS button (1) of master speaker or sub-speaker to switch Off the team pairing TWS mode.
3. When speakers are team paired TWS mode successfully under Bluetooth, the two speakers can still work as paired speakers by inserting the AUX cable into the AUX socket on the first speaker (Master), the Master speaker wiil be with green and blue LED light, the sub-speaker with green LED light. lWS mode will fail if AUX cable is inserted to the AUX socket on the second (linked) sub-speaker.
4. Under TWS status. only the master speaker will with response. and pick up phone. The second speaker is without response.

• PHONE CALLS

  • You could receive incoming calls with Bluetooth speaker if it paired to smartphone/tablet PC. You can talk using built-in mic and dynamic. Short press «Pause/Play/Ring» button to receive the incoming call, press once again to end the call.
  • Long press «Pause/Play/Ring» button is rejecting the incoming call

• AUX PLAY
  Use (supplied) cable and connect it to the Bluetooth Speaker by one side (AUX port) and the external device by another side. Be sure that cable is well connected

• BATTERY CHARGING
  Before first use, fully charge Bluetooth Speaker within 12 hours. New battery requires 2-3 full charge-discharge cycles to reach full capacity. Plug AC adapter (supplied) into power socket (110-230V) and connect it to the Bluetooth Speaker by DC IN side. LED indicator N”2 is turned on while charging and turns off when the battery fully charged

• CHARING DEVICES

  • You can charge your device with built-in USB-A ports. Turn on the Bluetooth Speaker. Connect your device to the USB port Ngl or N22 with cable, which is suitable for your device (not supplied) WIRELESS CHARGING (available only Woody Q and Woody W models)
  • You can charge your QI-compatible device (for example, smartphoneJ with built-in wireless charger. Turn on the Speaker, put your device, which is supporting wireless charging at the center of the tabletop. Take the device off the tabletop, when it fully charged

• STORAGE CONDITIONS
  Keep the device in a dry, well-ventilated place, far from heaters and direct sunlight. Keep the device out of reach of children. Do not bite or lick device, as it may cause damage or explode the device. Children or persons with disabilities should not use the device without the supervision of the responsible person

SAFETY INFORMATION

1. Before charging be sure that voltage of the power adapter is 16V. It’s strictly recommended to use provided power adapter. Be sure that DC power is 1 10-230V before connecting the power adapter
2. If Speaker not used for a long time, charge it at least once per month
3. In case of breaking, do not try to open and repair device by yourself. Use service center
4. Avoid high humidity influence, dust, and dirt. Use dry soft lint-free cloth to clean device. Not allowed to use washing or cleaning liquids
5. Do not store, use or charge device near heat sources and flammable objects, during l low or high ambient temperature. Charing can be done only under adult supervision. Recommended temperature is 5 to 35 ‘C
6. Not allowed to drop or hit device
7. Do not insert foreign objects to the device interfaces
8. Turn off device after use
9. Never pull the core to disconnect cable, pull the plug
10.  Bluetooth speaker is not intended for the commercial use
11. Bluetooth mode is not intended for the commercial use
12. Standarc battery life is 500 charge-discharge cycles. The effective capacity of the battery can be reduced after 500 cycles . Effective capacity also depends on the ambient temperature
13. Do not disassemble the device, do not subject it to excessive heat, and do not put it in water, as this can lead to the battery heating with a large heat release
14. Do not cover working device with cloth or other material
15. The maximum load weight is 5 kg. The product can’t be used as a sit, otherwise you can damage your health and the product

SAFETY INFORMATION FOR WIRELESS CHARGING

(Waddy Q and Woody W models only)

1. Do not use both types of charging at the same time. Before wireless charging disconnect the personal device from the USB port
2. Do not put a QI-compliant adapter, such as cover or wireless receiver, on the wireless charger without personal device. This can lead to malfunction of the device, overheating of the wireless charger and cause a fire
3. The impact of magnetic fields created by wireless charger can damage the magnetic cards, for example bank cards. Do not place magnetic cards near the wireless charger
4. Do not use wireless charging with not QI-compatible devices

DISPOSAL

Do not dispose with household waste! Required to dispose this electrical device at designated recycling collection point for electrical devices. It ensures that device is recycled proressionaly and prevents the release of the harmrul substance into the environment. Make sure that device is uncharged before disposal

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>