GE Lighting 99379 StayBright Random Sparkle LED Super Sphere User Guide

: June 9, 2024
: GE Lighting

Table of Contents

GE Lighting 99379 StayBright Random Sparkle LED Super Sphere
IMPORTANT SAFETY INSTRUCTIONS
USE AND CARE INSTRUCTIONS
USER SERVICING INSTRUCTIONS
Instructions for replacing the bulb
CAUTION
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GE Lighting 99379 StayBright Random Sparkle LED Super Sphere

IMPORTANT SAFETY INSTRUCTIONS

When using electric products, basic precautions should always be followed including the following:

READ & FOLLOW ALL SAFETY INSTRUCTIONS

This is an electric product-not a toy! To avoid the risk of fire, burns, personal injury, and electric shock, it should not be played with or placed where small children can reach it.
Do not use seasonal products outdoors unless marked as suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
Do not use this product for other than its intended use.
This seasonal use product is not intended for permanent use or installation.
Unplug when leaving the house, when retiring for the night, or if left unattended.
Do not mount or place near gas or electric heaters, fireplaces, candles, or other similar sources of heat.
Do not secure the wiring of the product with staples or nails, or place it on sharp hooks or nails.
Do not hang ornaments or other objects from the cord, wire, or light string.
Do not place lighting string on carpeting, drapes, or furniture, or allow it to contact vinyl siding while the power is on.
Do not perform any maintenance or troubleshooting for bad or broken lamps while the power is on.
Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
Do not cover the product with cloth, paper, or any material not part of the product when in use.
This product is equipped with non-shunted type LED lamps. Do not twist or attempt to remove lamps.
This product employs overload protection (fuse). A blown fuse indicates an overload or short–circuit situation. If the fuse blows, unplug the product from the outlet. Also, unplug any additional strings or products that may be attached to the product, Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
Do not let lamps rest on the supply cord or on any wire.
Read and follow all instructions that are on the product or provided with the product.

USE AND CARE INSTRUCTIONS

Before using or reusing, inspect the product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
Before storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
When not in use, store neatly in a cool, dry location protected from sunlight.
When the product is used on a live tree, the tree should be well-maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
If the product is placed on a tree, the tree should be well-secured and stable.

USER SERVICING INSTRUCTIONS

SAFETY PLUG WITH REPLACEABLE FUSE:
Risk of fire. Do not replace the attachment plug. Contains a safety device (fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Always unplug the product from the receptacle or other outlet device before installing or replacing a fuse.
Firmly grasp the plug to unplug. Do not unplug by pulling on the cord.
Open the fuse cover. Side open fuse access cover on top of attachment plug. towards the blades.
Remove fuses carefully by turning the plug over.
Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
Side closed the fuse access cover on top of the plug.

Instructions for replacing the bulb

If a damaged or burned-out bulb needs to be replaced, we recommend wearing gloves throughout the replacement process. While holding the sphere with one hand, use a tool to grab the damaged bulb closest to the husk and gently pull it straight up and out of the socket. Insert the spare replacement bulb that is provided with this product into the empty socket.

To replace the lamp:

Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.
Pull the lamp and plastic base straight out of the lampholder.
Replace the lamp with only a 3.3 Volt, 0.066 Watt, LED type lamp(provided with product).

CAUTION

This lighting string is rated 3.2 Watts (0.027Amps), and does not overload. Connect other lighting strings or decorative outfits end-to-end up to a maximum of 216 Watts (1.8 Amps) total. If connecting to a Lighting String that does not have a Wattage (W) rating, on the cord tag within 6 inches of the plug, calculate the wattage as follows: Multiply the current (A), which is also on that cord tag, by 120.
For example, The Lighting String is rated 120V, 60Hz, and 0.2Amps. 0.2x 120 = 24Watts.
Add the wattage of each light string together for a total of 216 Watts or less. (Do not exceed 216 Watts.)
To reduce the risk of overheating, a) replace burned-out lamps promptly. Use 3.3 Volt, 0.066Watt LED lamps provided with this product .b) Risk of fire. This product does not contain lamp shunts in order to allow the product to operate if one lamp burns out. Do not replace lamps other than the spare lamps provided with this product.
To reduce the risk of fire electric shock: a) Do not install on trees having needles, leaves, or branch coverings of metal or materials that look like metal, and b)Do not mount or support strings in a manner that can cut or damage wire insulation.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.

Warning:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com.

FOR INDOOR AND OUTDOOR USE MADE IN CHINA
PRINTED IN CHINA E246482 HC-22
Nicolas Holiday Ltd. 246 Spring Hill Road, Unit B, Trumbull CT 06611