GE Lighting 71026-0.14 21L JEWEL STAR User Guide

GE Lighting 71026-0.14 21L JEWEL STAR

IMPORTANT SAFETY INSTRUCTIONS

When using electric products, basic precautions should always be followed including the following:

• READ AND FOLLOW ALL SAFETY INSTRUCTIONS
• Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
• This seasonal use product is not intended for permanent installation or use.
• Do not mount or place near gas or electric heater, fireplaces, candles or other similar sources of heat.
• Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
• Do not let the lamps rest on the supply cord or on any wire.
• Unplug the product when leaving the house, when retiring for the night, or if left unattended.
• This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock, it should not be played with or placed where small children can reach it.
• Do not use this product for other than its intended use .
• Do not hang ornaments or other objects from cord, wire, or light string.
• Do not place lighting string on carpeting, drapes, or furniture, or allow it to contact vinyl siding while the power is on.
• Do not perform any maintenance or troubleshooting for bad or broken lamps while the power is on.
• Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
• Do not cover the product with cloth, paper, or any material not part of the product when in use.
• This product is equipped with push-in type lamps. Do not twist lamps.
• If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
• Read and follow all instructions that are on the product or provided with the product.

SAVE THESE INSTRUCTIONS

USE AND CARE INSTRUCTIONS

• When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
• If the product is placed on a tree, the tree should be well secured and stable.
• Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lamp holders or enclosures, loose connections, or exposed copper wire.
• When storing the product, carefully remove the product from wherever it is placed, including trees, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires.
• When not in use, store neatly in a cool, dr y location protected from sunlight.

USER SERVICING INSTRUCTIONS

Fuse replacement: Most often, fuses blow because too many sets have been strung end-to-end.

• Before changing fuses, make sure the set is unplugged.

• Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling on the cord.

• Using a flathead screwdriver, open the fuse cover.
  Slide open the fuse access cover on top of the attachment plug towards the blades.

• Remove fuses carefully.

• Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).

• Close fuse cover. Slide closed the fuse access cover on top of the attachment plug.
  Make sure the door is fully closed and the fuses are completely covered.

• Risk of fire. Do not replace the attachment plug. Contains a safety device(fuse) that should not be removed. Discard the product if the attachment plug is damaged.

Bulb replacement: Before changing bulbs, make sure the set is unplugged.

• Step 1: Grasp the plug and remove it from the receptacle or other outlet device. Do not unplug by pulling the cord.
• Step 2: Hold the bulb by the plastic base and pull the bulb/base straight out of the socket.
• Step 3: Replace the lamp with only 6 Volt, 0.84 Watt super brightness midget push-in type lamp provided with the product.
  Push spare bulb/base assembly into the socket. Do not twist the bulb when inserting it into the socket. If bulbs are twisted, part of the set will not light.

If the spare bulbs provided with the product have no plastic base or the plastic base does not fit, first follow steps 1-2 above. Then:

• Remove the old bulb by straightening the bulb wires and pulling bulbs straight from the base.
• Replace the new bulb by straightening the bulb leads and aiming each wire into a separate hole in the plastic base.
• Make sure each bulb lead comes out an exit opening at the bottom of the plastic base. Now bend each lead up such that each bulb lead fits closely against the narrow side of the plastic base.

CAUTION:

1. This lighting string is rated 16.8 Watts (0.14 Am ps), do not overload.
2. To reduce the risk of overheating, replace burned out lamps promptly. Use 6 Volt ,0.84 Watt lamps only.
3. To reduce the risk of fire and electric shock:
4. Do not install on trees having needles, leaves or branch coverings of metal or materials that look like metal, and
5. Do not mount or support strings in a manner that can cut or damage wire insulation.
   For questions and/or assistance, call customer service at 1-877-398-7337 or visit us on the web at www.GEholidaylighting.com.

FOR INDOOR USE ONLY E246482 HC-22
PRINTED IN CHINA 120 VOLTS MADE IN CHINA
©2022 Nicolas Holiday Limited, 9F., No. 37, Guangfu N. Rd Taipei, Taiwan 10560. All rights reserved.

References

• Arhitektura | Mismo arhitekturni kolektiv | Ljubljana

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>