GE Lighting 24LEDI-7MMb-600 LED 600 7MM Lights User Manual
- June 9, 2024
- GE Lighting
Table of Contents
GE Lighting 24LEDI-7MMb-600 LED 600 7MM Lights
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
- READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- Do not use seasonal products outdoors unless marked suitable for indoor and outdoor use. When products are used in outdoor applications, connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If one is not provided, contact a qualified electrician for proper installation.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplaces, candles or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
- Do not let lamps rest on the supply cord or on any wire.
- Unplug the product when leaving the house, when retiring for the night, or if left unattended.
- This is an electric product-not a toy! To avoid risk of fire, burns, personal injury and electric shock it should not be played with or placed where small children can reach it.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from cord, wire, or light string.
- Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
- Do not cover the product with cloth, paper or any material not part of the product when in use.
- This product is equipped with push-in type lamps. Do not twist lamps.
- Read and follow all instructions that are on the product or provided with the product.
- SAVE THESE INSTRUCTIONS
USE AND CARE INSTRUCTIONS
- When the product is placed on a live tree, the tree should be well maintained and fresh. Do not place on live trees in which the needles are brown or break off easily. Keep the tree holder filled with water.
- If the product is placed on a tree, the tree should be well secured and stable.
- Before using or reusing, inspect product carefully. Discard any products that have cut, damaged, or frayed wire insulation or cords, cracks in the lampholders or enclosures, loose connections, or exposed copper wire.
- When storing the product, carefully remove the product from wherever it is placed, including tree, branches, or bushes, to avoid any undue strain or stress on the product conductors, connections, and wires
- When not in use, store neatly in a cool, dry location protected from sunlight.
USER SERVICING INSTRUCTIONS
Replace the lamp.
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling cord.
- Pull lamp and plastic base straight out of lamp holder.
- Replace lamp with only 3.3 Volt, 0.066 Watt, LED type lamp (provided with product).
If the new lamp base does not fit in lampholder, follow the steps below step 3.
- Remove the base of the burned-out lamp by straightening lamp leads and gently pulling lamp out.
- Thread leads of new lamp through holes in old base with one lead in each hole.
- After lamp is fully inserted into base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lamp holder.
CAUTION:
- Replace lamps only with 3.3 volt, 0.066 watt spare lamps provided with this product.
- Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Do not replace lamps with other than the spare lamps provided with this product.
TROUBLESHOOTING
| PROBLEM | POSSIBLE CAUSE | CORRECTIVE ACTION |
|---|---|---|
| If the product does not light | One or more of the based LEDs may have loosened |
from the socket during transporting. There is a break in the circuit between the LED leads and the socket terminals. Male/female connectors not fully inserted together. Non working control box.
Foot pedal in off
position.
| Unplug the set at the outlet. Starting with the first unlit LED, gently push
(don’t twist) each LED base firmly into the socket. If still does not light,
then remove each based LED and check for out of place lead wires. Make certain
connectors fully inserted and securing cap fully tightened. Step on foot pedal
to turn LEDs on.
If a based LED is missing| One or more of the based bulbs may have come out of
the socket when transporting.| Mark socket(s) with a piece of tape and unplug
the set. Replace the based LED or
use one of the spare based LEDs included with product.
If an LED fails to light (shorts or
opens)
| Incorrect LED, premature LED failure or voltage is too high.| The LED may be
out or dimly lit. Replace bad LEDs as soon as you find them.
LEDs fail to switch from white
to multi
| If applicable, then a defective control box or color change foot
pedal.
| Contact Customer Support.
FCC Rules
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
For questions and /or assistance, call customer service at
1-877-398-7337 or visit us on the web
at www.geholidaylighting.com ©2022 Nicolas
Holiday Limited FP-22 PRINTED IN CHINA 246 Spring Hill Road, Unit B, Trumbull
CT 06611 9F., No. 37, Guangfu North Rd. Taipei, Taiwan 10560 All rights
reserved.
GE is a trademark of General Electric Company and is under license by Nicolas
Holiday Limited.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>