GLOBALO Saredo 60 Built In Kitchen Extractor Range Hood Instruction Manual

Saredo 60 Built In Kitchen Extractor Range Hood
Instruction Manual

Alario 60 Built In Cooker Hood

Dear Customers,
Thank you for choosing our brand. We hope that you will be satisfied with our product. Every product that leaves our production plant is carefully inspected for quality and  safety. Before installation and use of the hood, you are kindly requested to read this manual carefully and follow the safety instructions. We also recommend that you keep the  manual in an easily accessible place so that you can consult it at any time.

GLOBALO team
In order to ensure the maximum safety of the device, the most important information has been marked with the following symbol:

Company Headquarters
GLOBALO
ul. Maków 10
38-500 Sanok
Poland
Tel.: +48 13 49 27 560
https://globalo.pl
e-mail: biuro@globalo.pl
Service:
Phone: +48 13 49 27 560 extension 3
Mobile phone.: +48 609 055 660
e-mail: serwis@globalo.pl
https://globalo.pl/serwis/

GENERAL INFORMATION ON SAFETY AND INSTALLATION

• Keep the manual in an easily accessible place so that you can consult it at any time.
• This manual contains detailed information on the installation and maintenance of the range hood.
• The product may slightly differ from the range hood presented in this manual, but the recommendations regarding operation, maintenance and installation apply to the  same extent.
• Do not introduce any changes to the electrical installation or physical structure of the hood.
• Do not connect the device to the power supply before completing the installation process.
• Use protective gloves for all installation and maintenance operations.
• Do not use the hood without a properly installed anti-grease filter.
• Installation not in accordance with these instructions poses a risk of electric shock.
• Do not use sources of open fire underneath the hood.
• Keep a close eye during deep frying – overheated fat can easily ignite.
• The air sucked in by the hood must not be discharged into a flue pipe used for exhaust fumes from appliances burning gas or other fuels (this does not apply to  recirculation hoods).
• If you have other non-electric appliances in the house (e.g. liquid fuel cookers, flow-through heaters, water heaters) make sure that there is sufficient air supply in the  room.
• Do not pull on the power cord to disconnect the plug from the socket.
• The power cord must not be in contact with any hot surfaces.
• Do not switch on the device if the power cord is damaged.
• A damaged power cord may only be replaced by the manufacturer, repair centre or a qualified specialist.
• The hood should be cleaned both inside and outside. at least once a month or every 35 hours of operation. Each time before cleaning the hood, disconnect the power  supply (unplug the power cord or pull out the fuses).
• Children at least 8 years old, persons with physical or mental disabilities and persons with lack of knowledge or experience in using the device may use it only under  supervision or after being properly instructed in terms of safe operation.
• Children should not be allowed to play with the device.
• Children are not allowed to clean the device without supervision.

CAUTION!
EASILY ACCESSIBLE PARTS MAY BECOME HOT WHEN THE COOKER IS USED. USING SCREWS OR FASTENERS OTHER THAN APPROVED IN THE  MANUAL MAY RESULT IN ELECTRIC SHOCK.

ENVIRONMENTAL PROTECTION

The product is made of high quality recyclable materials.
The symbol of a crossed-out wheelie bin on the product (Fig. 1) indicates that the end users should segregate the product from other waste at end-of-life, in accordance with  the provisions of Directive 2012/19/EU of the European Parliament and of the Council. If the symbol shown in Fig. 2 is used, it means that the product contains batteries,  which the end users should segregate from other waste at end-of-life, in accordance with the provisions of Directive 2006/66/EU of the European Parliament and of the  Council.
The mentioned marking means that end-of-life electrical and electronic equipment and batteries (if any) must not be disposed of with other household waste. The user is  obliged to return used electrical and electronic equipment and batteries (if any) to special collection points for such items. Operators of collection facilities, including local  collection points, shops and municipal units must have in place an appropriate system enabling the users to return such equipment and batteries.
Proper disposal of waste equipment and batteries prevents harmful impact of hazardous components of these items on human health and the environment, resulting from  improper storage and handling of such equipment and batteries. Individual households play an important role in ensuring reuse and recovery, including recycling, of waste  equipment, helping to preserve clean environment, which is our common good. It is also households that are the largest consumer of small appliances, hence rational  management of waste improves the efficiency of secondary raw materials recovery. Improper disposal of this product may result in penalties, imposed in accordance with  national legislation.

TECHNICAL SPECIFICATION

The technical specification presented in this manual and on the labels placed on the product is based on measurements and calculations in accordance with the requirements  of EU Regulation 65/2014 and 66/2014.

ALARIO 60/80

Supply Voltage| 220 – 240V
Frequency:| ~50 Hz
Motor power:| 200 W
Number of speed levels:| 3
Lighting power:| 1×5 W
Total Power:| 205 W
Security class:| II
Outlet diameter:| Ø15 cm

INSTALLATION AND OPERATION

The range hood is designed for fume and smoke extraction during food preparation.
CAUTION!

• USE THE SHORTEST POSSIBLE EXHAUST DUCT.
• USE AN EXHAUST DUCT WITH A SMOOTH INTERNAL SURFACE (SPIRO DUCTS ARE NOT RECOMMENDED).
• ANY BENDING OF THE DUCT SHOULD BE LIMITED TO MINIMUM (THE ANGLES SHOULD NOT EXCEED 90°).
• COMBINING DUCTS WITH DIFFERENT CROSS-SECTIONS IS NOT RECOMMENDED (E.G. Ø15 CM WITH Ø12 CM).
• ENSURE THAT THE SIZE OF THE SUCTION OPENING IS AT LEAST AS BIG AS THE SIZE OF THE AIR EXHAUST. THIS WILL PREVENT  NEGATIVE PRESSURE AND ENSURE PROPER FUNCTIONING OF THE HOOD.
• IF THERE ARE ANY OPEN-FLAME APPLIANCES IN THE ROOM (E.G.: SOLID AND LIQUID FUEL COOKERS, FIREPLACES, HEATERS, ETC.).  MAKE SURE THERE IS AN ADEQUATE SUPPLY OF FRESH AIR.

CAUTION!
USE SCREWS AND FASTENERS APPROVED IN THE MANUAL TO AVOID THE RISK OF ELECTRIC SHOCK.
The minimum distance between the surface of the cooker and the lowest part of the range hood (see figure below) must be at least 45 cm for electric cookers and 65 cm for  gas cookers. If the cooker manual indicates a greater distance than specified above, follow the instructions in the cooker manual.

Installation of the product is shown in Figures 5 – 12. During installation, follow the general regulations concerning air extraction.

PREPARATION BEFORE HOOD INSTALLATION

• Check whether the dimensions of the purchased product are suitable for the selected place of installation.
• Disconnect and remove (if possible) any appliances in the installation space to facilitate access to the ceiling or wall where the hood will be installed. If this is not  possible, secure these elements.
• Check whether there is a socket near the hood installation space and whether it is possible to connect the hood to a ventilation duct for fume extraction.
• Make sure there are no lines of electric and plumbing installations in places where holes will be drilled.
• Prepare the following tools: tape measure, pencil, drill/driver, Ø3 mm drill bit, screwdriver, level.

CAUTION!
TAKE CARE NOT TO SCRATCH THE HOOD.

HOOD INSTALLATION

1. Prepare the cabinet where the hood is to be installed by cutting a hole in the bottom of the cabinet as shown in the figure.
   

2. Remove the aluminium anti-grease filter.
   

3. Drill four Ø3mm blind holes and insert screws.
   

4. Place two angle brackets on the screws and mount the hood by screwing in six Allen screws.
   

5. To adjust the hood position, place the hood so that the bottom panel leans against the drawer’s underside by adjusting element A, then tighten the screws with a  screwdriver.
   

6. Install the grease filter.
   

7. Connect the duct to the motor connection.
   

POWER SUPPLY CONNECTION
The supply voltage must correspond to the voltage indicated on the identification plate placed inside the hood. If the hood is equipped with a plug, insert it in an accessible  socket compliant with the applicable regulations. If the hood is not equipped with a plug, the installation should be carried out by a certified specialist (e.g. an electrician).
CLEANING AND MAINTENANCE
Before performing any maintenance operations, unplug the device from the socket. Use mild detergents for cleaning. Do not use abrasive cleaning products.
The hood should be cleaned at least once a month or every 35  hours of operation.
DO NOT USE  ALCOHOL-BASEDCLEANING AGENTS.
Inox parts should be cleaned with special product (e.g. BERNER).
CARBON FILTER
The hood may be equipped with a carbon filter. Use the filter only when the hood is not connected to the ventilation duct. Place the filter on the turbine housing as shown in  Fig. 13. The filter should be replaced every 3-6 months.

ANTI-GREASE FILTER

The hood is equipped with an aluminium filter which partially traps grease particles. You can wash the filter manually by immersing it for 15 minutes in 40-50ºC water with  dishwashing liquid.
After 15 minutes, wash and rinse the filter thoroughly. Dry well before placing it back in the hood.
You can also wash it in a dishwasher. After cleaning, you may notice a slight discolouration of the filter, which does not affect its properties. A regularly cleaned filter will help to maintain the efficiency of the hood and prevent the risk of fire.

SETTINGS (BUTTONS ON THE HOOD OR REMOTE CONTROL)

LED display
The selected speed level (1,2,3,4) will be shown on the display 3.
Speed adjustment
Pressing the minus „–” button 2 will decrease the speed of the turbine.
Pressing the plus „+” button 4 swill increase it.
Switching the hood motor on and off
The hood motor can be started in 3 ways:

1. Pressing the button – the motor will switch on at the same speed level at which it was switched off.
2. Pressing the minus „–” button – the motor will switch on at the minimum speed level.
3. Pressing the plus „+” button – the motor will switch on at the maximum speed level.
4. Switching the lighting on and off
5. To turn the hood lighting on, press . Pressing the button again turns the lighting off.

Switching the lighting on and off
To turn the hood lighting on, press . Pressing the button again turns the lighting off.

Timer 15 minutes
The control panel of the hood is equipped with a turbine timer, which turns it off 15 minutes af-ter the timer is activated. In order to activate the timer, the hood turbine must  be running at any speed. The timer is activated / deactivated by pressing the button on the remote control until the dot starts blinking on the display in the bottom  right corner.
The metal filters should be cleaned more frequently, if required!
The control panel of the hood is equipped with a functionality that automatically switches off the turbine if the control panel has not been used for 2 hours.

IN CASE OF PROBLEMS

The range hood does not function at all:

• Check whether the fuse in the domestic installation is not pulled out.
• Check if the thermal cutout of the motor has not been activated due to high temperature. If this is the case, switch off the device and wait for about 20 – 30 minutes until the temperature returns to normal; then switch the hood on again.
• Make sure that the plug is inserted in the socket.
• Remove the plug to restart the device. Wait for about 15 – 20 seconds and then plug it back in.
  Alternatively, you can also pull out the fuse for that time and then put it back in.

Insufficient efficiency/noisy operation:

• Check whether the cross-section of the ventilation duct is sufficient and whether it has not too many bends and sharp angles.
• Check if the return flap (if optionally installed) is not jammed in the ventilation duct.
• If the ventilation duct is equipped with a swinging grille, remove it.
• Make sure that the metal filters are clean.
• Replace the active carbon filter if it is older than 6 months (only in recirculation mode).
• Check whether the amount of air extracted from the kitchen is balanced by sufficient fresh air supply (to prevent negative pressure).
• Check whether the ventilation chimney is not obstructed.
• Excessively low atmospheric pressure may reduce the performance of the hood. Verify the functioning of the hood again on another day.

ENERGY LABEL

The above energy label is only an example. The actual data can deviate from that specified above in any other model.

REDUCING THE IMPACT OF COOKING ON THE ENVIRONMENT

• In order to reduce energy consumption, cover pots and pans with lids while cooking.
  Keep the aluminium filters clean (the recommended cleaning schedule for the filter is at least once every 35 hours).

• Keep the ventilation ducts unobstructed.

• Always set the turbine speed during cooking to the minimum required level, allowing for fume extraction at the current cooking intensity.

SERVICE AND MAINTENANCE
If, despite our strict quality control, you find any irregularities in the operation and functioning of the purchased device, please contact our service department to receive  professional assistance of our team.
The service support is available Monday to Friday from 9.00 am to 5.00 pm at: +48 13 49 27 560 extension: 3 and +48 609 055 660 or by email at: serwis@globalo.pl.

Before connecting the service, please take down the following details of your device:
Type: ___
Seria-Nr: ____
You can find this information on the identification plate. The plate is located inside the hood and is visible after removing the metal filters.

The identification plate shown in the figure above is only an example. The data may differ for other models.
To request a hood repair, you can use the form available at https://globalo.pl/serwis/.

TROUBLESHOOTING

When the hood is operating, a flashing „F”
appears on the display.| After 35 hours of operation, the display
indicates that the anti-grease filter needs
to be cleaned or replaced.| Press and hold down for approx.
6s the „-” button on the panel. Clean the
filter or replace it with a new one.
The display only shows
the „-.” sign (minus and dot in the lower
right corner), the hood does not start
when switched on.| The touch panel is locked (this is a
function used to facilitate cleaning of
the hood).| To deactivate the lock, press and hold the
on/off sign for approx. 10s.
No sign appears on the display, the hood
does not respond to the buttons.| The control panel may be frozen.| Disconnect the hood from the power
supply for approx. 15 seconds and then
switch it on again.
The display shows the sign of one of the
speed levels and the hood does not react
to the buttons.| The control panel may be frozen.| Disconnect the hood from the power
supply for approx. 15 seconds and then
switch it on again.
The hood turbine switches off after
15min. of operation and the display blinks with, for instance „1” (the  number of the current speed level and a  dot in the lower right corner of the display*.| The automatic timer of the control panel has been activated.| To deactivate the timer, press the plus
sign for about 10 seconds or switch off
the device.

• applies to range hoods with touch control
  If after following the above-mentioned guidelines the problem is still not solved, contact an authorised household appliance repair service.
  Do not try to repair the hood yourself. A list of authorised repair centers is provided on the warranty card and on the website.

LED STRIP REPLACEMENT
The installation must be carried out by qualified personnel.

WARRANTY

Within the period of 2 years from the date of purchase of the product, GLOBALO undertakes to cover all repair costs for faults which are obviously caused by manufacturing defects. The warranty does not cover burnt bulbs, fuses and filters, as well as any damage due to faulty installation and ventilation system.
In addition, the warranty does not apply in the following cases:

• Application in the catering industry.
• Application for any other purposes than household use.
• Use of the device not in accordance with the operating instructions and its intended purpose.
• Circumstances beyond the control of the manufacturer, including, without limitation: uncontrolled power surge, flooding, obstruction of the ventilation duct.
• Apparent mechanical damage after installation of the device.

CAUTION!

• ANY PRODUCT WITH MECHANICAL DAMAGE, WHICH HAS NONETHELESS BEEN INSTALLED, WILL NOT BE REPLACED! BEFORE  INSTALLATION OF THE DEVICE, UNPACK IT AND CAREFULLY INSPECT IT FOR ANY MISSING COMPONENTS OR DAMAGE. ANY VISIBLE  EXTERNAL DAMAGE CLAIMED AFTER INSTALLATION IS EXCLUDED FROM THE WARRANTY.
• GLOBALO MAX SHALL NOT BE HELD LIABLE FOR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY PERSONS, ANIMALS OR OTHER OBJECTS AS A RESULT OF NON-COMPLIANCE WITH THE  INSTRUCTIONS IN THIS MANUAL, IN PARTICULAR THOSE CONCERNING INSTALLATION, OPERATION AND MAINTENANCE OF THE DEVICE!

References

• Ciche i wydajne Okapy Kuchenne | GLOBALO
• Serwis GLOBALO

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>