ENERLITES 962301-C-D Brass Pop up w TRWR Outlet and Triple RJ45 Jacks Instruction Manual

ENERLITES 962301-C-D Brass Pop up w TRWR Outlet and Triple RJ45 Jacks

Product Information

Specifications:

• Description/Features: Two gang pop-up floor box assemblies, including two 20 amp decorator duplex tamper & weather-resistant receptacles, FB-12 box, gasket, and cover.
• Dimensions: 5/16(7.3mm) x 4-3/4(120mm) x 2-3/8(61mm)

Product Usage Instructions

Installation Instructions:

1. Turn off the POWER at the circuit breaker before installing the Floor Box.
2. Read and understand the provided instructions before installation.
3. Ensure the device is installed following the National Electric Code and local regulations.
4. It is recommended to have a qualified electrician perform the installation.

Wiring Directions:

1. Connect the HOT wire to the BLACK wire.
2. Connect the NEUTRAL wire to the WHITE wire.
3. Connect the GROUND wire to the GREEN wire on the switch.

Floor Box Installation:

1. Ensure there is sufficient depth and space below the subfloor before installation.
2. For carpeted floors, cut out the carpet based on the size of the cover. For wood subfloors, route as indicated.
3. Remove knockouts and secure the box onto the floor. Pull the wire through the opening and connect based on the wiring diagram.
4. Attach the box to the floor using #6 wood screws (not provided).
5. Attach the cover to the box using #6-32 mounting screws and tighten firmly.

Warranty Information:
For warranty details, please refer to the warranty information provided with the product.

FAQ :

• Q: Can I use this floor box assembly outdoors?
  A: The product is designed for indoor use. Outdoor use may require additional weatherproofing measures.

• Q: What wire gauge is recommended for installation?
  A: It is recommended to use 10-12 AWG Stranded or Solid Copper wire for installation.

Two Gang Pop-up Floor Box Assembly with 20A Decorator Duplex Tamper & Weather Resistant Receptacle and RJ45

SPECIFICATIONS

• Cover Material………………………………………Brass(C) or Nickel-Plated Brass(S)
• Receptacle Rating……………………………………………………………….20A 125VAC

Box:

• Box Material…………………………………………………………………..Pre-galvanized
• Knockout Size…………………………………………………………….Steel 1/2″ and 3/4″
• Adjustable Height………………………………………………………………..Up to 1″ depth

DESCRIPTION/ FEATURES

Two gang pop-up floor box assemblies, including two 20 amp decorator duplex tamper & weather resistant receptacles, FB-12 box, gasket and cover.

• Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Nickel-Plated Brass(S).
• Corrosion-resistant hardware ensures a long life span and reliable performance.
• Easy access to power when you need it. Snap the cover closed when not in use.
• Used for carpet and wood floors. Also great for countertop applications.

WARNING
Turn the POWER OFF at the circuit breaker before installing the Floor Box
Read and understand these instructions before installing. This device is intended for installation per the National Electric Code and local regulations. It is recommended that a qualified electrician performs thi installation. Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only, or equivalent.

NOTES:
10-12 AWG Stranded or Solid Copper wire is recommended.

WIRING DIRECTIONS

1. Connect the HOT wire to the BLACK wire.
2. Connect the NEUTRAL wire to the WHITE wire.
3. Connect the GROUND wire to the GREEN wire on the switch.

FLOOR BOX INSTALLATION

Before Installation:
Ensure there is sufficient depth & space below the subfloor.

Step 1
For carpeted floors:
Cut out the amount of carpet based on the size of the cover.

For wood sub-floors

• Tape the template on the area you want to place the floor box.
• Use a knife to cut the outline of the box. Start with the ears and move inwards. Cut the box shape without the ears completely through the subfloor.
• Cut 1/4″ depth into the subfloor for the mounting ears.
• Using a router is recommended

Step 2

• Remove knockouts and secure the box onto the floor.
• Pull the wire through the opening of the floors and knockouts and connect wires based on the wiring diagram.

NOTE :

• Attach the box to the floor using #6 wood screws (not provided).
• Attach the cover to the box using #6-32 mounting screws and tighten firmly.

DIMENSIONS

WARRANTY INFORMATION

This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. An original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This warranty is non-transferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end-user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement, or refund. Repair, replacement, or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
© 2016 Enerlites Inc. CA, U.S.A.
WWW.ENERLITES.COM
0206160010-01
REV 20230802

References

• Manufacturing Lighting Controls & Wiring Devices - Enerlites

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>