ROMMELSBACHER ES 850/E Stainless Steel Juicer Instruction Manual

ROMMELSBACHER ES 850/E Stainless Steel Juicer

Product description

Control panel

Introduction

We are pleased you decided in favor of this superior juicer and would like to thank you for your confidence. Its easy operation and wide range of applications will certainly fill you with enthusiasm as well. To make sure you can enjoy using this appliance for a long time, please read through the following notes carefully and observe them. Keep this instruction manual safely. Hand out all documents to third persons when passing on the appliance. Thank you very much.

Intended use

The appliance is designed for extracting the juice from fruit and different kinds of vegetables (domestic use only). Other uses or modifications of the appliance are not intended and harbour considerable risks. For damage arising from not intended use, the manufacturer does not assume liability. The appliance is not designed for commercial use.

Technical data

Only connect the appliance to an isolated ground receptacle installed according to regulations.
The rated voltage must comply with the details on the rating label. Only connect to alternating current.

• Nominal voltage: 220-240 V~ 50/60 Hz
• Nominal power: 800 W
• Protection class: II
• Maximum continuous operation time: 30 minutes

Scope of supply
Check the scope of supply for completeness as well as the soundness of the product and all components (see product description page 2) immediately after unpacking.

Packing material
Do not simply throw the packing material away but recycle it. Deliver paper, cardboard and corrugated cardboard packing to collecting facilities. Also put plastic packing material and foils into the intended collecting basins.

In the examples for the plastic marking:
PE stands for polyethylene, the code figure 02 for PE-HD, 04 for PE-LD, PP for polypropylene, PS for polystyrene.

For your safety

WARNING: Read all safety advices and instructions!
Non-observance of the safety advices and instructions may cause electric shock, fire and/or bad injuries!

General safety advices

• Always keep children away from the product and the power cord.
• Children must not use this appliance.
• Persons not having the knowledge or experience in operating the appliance or having handicaps of physical, sensorial or mental nature must not operate the appliance without supervision or instruction by a person, responsible for their safety. Never leave the appliance unattended during operation.  • Children should be supervised in order to ensure that they do not play with the appliance.
• Packing material like e. g. foil bags should be kept away from children.
• Do not operate this unit with an external timer or a separate tele control system.
• Prior to each use, check the appliance and the attachments for soundness, it must not be operated if it has been dropped or shows visible damage. In these cases, the power supply must be disconnected and the appliance has to be checked by a specialist.
• When laying the power cord, make sure that no one can get entangled or stumble over it in order to avoid that the appliance is pulled down accidentally.
• Keep the power cord away from hot surfaces, sharp edges and mechanical forces. Check the power cord regularly for damage and deteriorations. Damaged or entangled cords increase the risk of an electric shock.
• Do not misuse the power cord for unplugging the appliance!
• Never immerse base unit, power cord and power plug in water for cleaning.
• Do not store the appliance outside or in wet rooms.
• This electrical appliance complies with the relevant safety standards. In case of signs of damage to the appliance or the power cord, unplug the appliance immediately. Repairs may be affected by authorized specialist shops only. Improper repairs may result in considerable dangers for the user.
• Improper use and disregard of the instruction manual void all warranty claims.

Safety advices for using the appliance

WARNING: Risk of injuries! During operation, do not use your fingers or other objects to stir in the filling hole or the grater!Only use the provided pusher for pressing down the food!

Thus, act with caution:

• The grater is very sharp; therefore handle it with care to avoid injuries!
• It is imperative to keep your hair, hands and clothes away from the filling hole and the grater to prevent getting hurt.
• Avoid any no-load operation and do not handle the appliance with hands wet.
• The appliance keeps running for ca. 10 – 15 seconds after it has been switched off – therefore please wait until it has stopped before opening the top cover.
• Never operate the appliance when the grater is defective.
• Empty the pulp container regularly so that the pulp can be thrown out any time and does not block the grater.
• Observe the following when setting up the appliance:
  • Place the appliance on a heat-resistant, stable and even working surface. o Do not operate the unit in the vicinity of sources of heat (oven, gas flame etc.) or in explosive environments, where inflammable liquids or gases are located.
  • Place it beyond children’s reach.
  • Leave a sufficient space around the appliance to ensure an unobstructed working area. See to a free air circulation.
• Pull the mains plug after each use for safe switch-off.

Functionality
The food is filled-in through the filling hole and pressed down with the pusher. The food gets on the quickly rotating grater and is grated finely. Due to the centrifugal force, the grated food is pressed on the aslant surfaces of the micro-mesh filter. There, the juice is extracted. The pulp is thrown out; the gained juice gets in the juice container and in a vessel via the spout.
The higher the speed setting, the higher is the rotation speed of the grater. The speed level has influence on the juicing results. You can select the settings to your individual taste.

Integrated safety system

The appliance has a double protection. It can only be operated if both locking clamps are closed and have engaged properly. Together with the observance of the advices of this instruction manual, this safety system ensures a safe operation of the appliance.

• If the power plug gets connected to the mains but the rear locking clamp is not shut correctly, the display remains off.
• If the rear locking clamp is opened during operation, the appliance will stop and the display goes out. After having closed the clamp again the appliance restarts at the set speed level.
• If the power plug gets connected to the mains but the front locking clamp is not shut properly, the display will show a blinking “L”.
• After the correct locking of the front clamp the display will show “0”.
• If the front locking clamp is opened during operation, the appliance will stop and the display shows a blinking “L”. As soon as the clamp gets relocked the appliance will restart at the set speed level.

Integrated motor protection

The appliance has an integrated motor protection against overheating which prevents the motor from getting damaged in case of overloading.

• If the motor temperature rises over 110 °C the appliance will stop automatically and the temperature indication in the display starts blinking.
• Wait until the motor has cooled down below 100 °C.
• For a restart of the appliance turn the rotary knob to “OFF“ position first and then select the desired speed level.

Prior to initial use
For a start, please clean the appliance as well as all attachments. For more detailed information please refer to “Cleaning and maintenance”.

Disassembly and assembly

ATTENTION: Hazard of injury! The grater keeps running for ca. 10 – 15 seconds after it has been switched off; therefore disassemble the juicer only at standstill!
Do not grasp in the filling hole and the grater! The grater is very sharp; handle it with care to avoid injuries!

How to disassemble your appliance

• Switch the appliance off.
  Turn rotary knob to “OFF“ position and pull the mains plug!

• Remove the pulp container.
  To do so, take the pulp container at the recessed grips and lift the container slightly until it comes off the base lock. Afterwards tilt the container slightly and remove it.

• Remove the top cover.
  Open both locking clamps and fold them aside. Now, remove the top cover. Then remove the pusher from the filling hole.

• Remove the juice container and the grater.
  Position your thumbs one below the spout, one below the fixture of the lock for pulp container. Then slightly push the juice container upwards until the grater disengages. Cautiously remove the grater with the micro-mesh filter by grasping it at its rim and lifting it to the top.
  Remove the juice container next.

• Disassemble the juice jug.
  Remove the top cover of the juice jug then pull the foam separator out.

How to assemble your appliance

• Switch the appliance off.
  Turn rotary knob to “OFF“ position and pull the mains plug!

• Attach the juice container.
  Take the juice container and place it on the intended bulge on the base unit.

• Attach grater with micro-mesh filter.
  Take the grater carefully at the rim of the micro-mesh filter and place the grater on the drive. Press against the edge of the grater with both thumbs until the grater engages. You will hear a clear “click” when the parts engage. Check the correct seat of the grater by turning!

• Attach and lock the top cover.
  Take the top cover and place it on the juice container. The filling hole must be centrally above the grater. Fold the two locking clamps up and hook the clamps into the intended bulges of the top cover. Now, push the locking clamps inwards until they engage. Check the firm locking of the clamps! Insert the pusher into the filling hole.

• Attach the pulp container.
  Take the pulp container at the recessed grip and position it slightly aslant below the top cover. Then tilt the container to the back and push it downwards until it engages in the base lock.

• Assemble the juice jug.
  Take the foam separator and insert it in front of the two bars and push it downwards as far as it will go.
  Then attach the top cover.

Operating the appliance

ATTENTION: Hazard of injury! Never reach into the filling hole or the grater! The grater is very sharp; handle it with care to avoid getting hurt!

NOTE: The appliance is designed for a maximum continuous operation time of 30 minutes. If this time has been reached, the appliance has to cool down for at least 10 minutes. If this is not observed, the motor might be damaged!

• The juicer is not qualified for chopping and grating coffee beans, nuts, nutmegs, cereals, meat etc. as well as for puréeing soup.
• Clean the grater and the filter regularly so that the micro-mesh filter does not congest.
• Empty the pulp container regularly.
• We recommend coating the pulp container with a suitable plastic bag where the pulp is collected. This will make the cleaning easier.

Preparing the appliance for use

• Assemble the appliance.
  Make sure the juicer has been correctly and properly assembled and that the grater does not show any damage (see point “How to assemble your appliance”).

• Place the provided juice jug or any other suitable vessel below the spout.

• Switching on or off
  Turn rotary knob to “OFF“ position and plug in the appliance.
  The display will show: NOTE: If no further setting is made within 5 minutes, the display will switch off. The appliance is in standby mode now.

• Switch the appliance on.
  For starting the appliance, turn the rotary knob clockwise to the desired speed level. The speed is classified in 5 levels, displayed as follows:

NOTE: The appliance has a “soft-start”, i e. the appliance starts slowly and increases the speed evenly to the level you set.

• Fill the food in the filling hole and press down with the pusher. This can be repeated according to requirements. Make sure that you do not fill too much food in and that you do not apply too much pressure with the pusher. The best results will be achieved if you press down the pusher slowly.
  Please make sure that the vessel below the spout does not spill and that the pulp container is not too full.

• Switch the appliance off.
  For switching off, turn the rotary knob to the left to the position “OFF”.

Always pull the mains plug after the extracting procedure has been finished!

Emptying the pulp container during use
When extracting larger quantities, the pulp container should be emptied regularly to ensure a trouble-free operation of the appliance.

• Switch the appliance off – pull the mains plug!
• Remove the pulp container (see “How to disassemble your appliance”.)
• Clean the pulp container.
• Attach the pulp container (see “How to assemble your appliance”).
• Before plugging the appliance in make sure that you have not accidentally switched it on!
• Switch the appliance on and resume working.

Easing blockages of the grater during use
During use, it might happen that the pulp accumulates below the filling hole and blocks the grater. This can happen if you process very hard and fibrous food too quickly and with too much pressure on the pusher. Then, it is necessary to ease this blockage.

ATTENTION: Hazard of injury! The grater keeps running for ca. 10 – 15 seconds after is has been switched off, therefore disassemble the juicer only at standstill!
Do not grasp in the filling hole and the grater. The grater is very sharp; handle it with care to avoid injuries!

• Switch the appliance off.
  Turn rotary knob to “OFF“ position and pull the mains plug!

• Remove the top cover (see “How to disassemble your appliance”).

• Now, carefully ease the blockage in the grater with a spoon made of wood or plastic.

• Attach and lock the top cover (see “How to assemble your appliance”).

• Before plugging the appliance in make sure that you have not accidentally switched it on!

• Switch the appliance on and start working again.

Cleaning and maintenance

ATTENTION: Risk of injuries! Always unplug the appliance before cleaning!
Do not grasp in the filling hole and the grater. The grater is very sharp; handle it with care to avoid injuries!
Never immerse base unit and mains plug in water or clean them under running water!

• Clean the appliance immediately after use so that residues will not dry up.
• Highly pigmented foods (e. g. carrots) may stain the appliance’s plastic parts or accessories. Wipe those parts with some cooking oil before cleaning them.
• The following parts are suitable for cleaning in the dishwasher
  • Pulp container, top cover with filling hole, foam separator and top cover of juice jug, juice jug, juice container with spout, pusher
• The following parts are not suitable for cleaning in the dishwasher:
  • Base unit, grater with micro-mesh filter, cleaning brush
• Remove all detachable parts from the base unit.
• Clean the base unit with a moist cloth and wipe it dry.
• Clean all other parts in hot water with some dishwashing detergent or if suitable in the dishwasher.
• Clean grater with micro-mesh filter.
• Clean the grater with the micro-mesh filter in hot water with some dishwashing detergent and the provided cleaning brush. The grater is very sharp-edged. Therefore, only touch the grater at the rim of the filter. Make sure that especially the micro-mesh filter is cleaned thoroughly.
• Do not use any abrasives or solvents or sharp-edged objects!
• Never use a steam jet appliance for cleaning!

Tips for extracting juice

• Prepare the food before extracting:
  • Clean fruit and vegetables thoroughly with water, scrub with a brush if necessary.
  • Peaches, apricots, plums, cherries etc. must be pitted.
  • Melons, pomelos, oranges, tangerines, citrons, grapefruits, kiwis, onions etc. must be peeled.
  • Celery, cucumbers or other large food which do not fit in the filling hole have to be cut in suitable pieces.
  • Apples, pears, strawberries, carrots, salad, radish, cabbage, spinach, parsley, tomatoes etc. must not be prepared.
  • Bananas, avocados, aubergines, figs, rhubarb etc. are not suitable for extracting.
• Fill fruit juice in ice cube trays and make tasty ice cubes which will certainly not water any drink down.
• The pulp which remains after extracting contains many nutritive substances and dietary fibres and can be used for cooking and baking. Use it for e. g. vegetable soups, casseroles or cakes (e. g. carrot cake) and fruit desserts.
• The stated data in the below chart are approximate values and mainly depend on the freshness and quality of the food as well as on the personal taste.

Service
Rommelsbacher ElektroHausgeräte GmbH Rudolf-Schmidt-Straße 18
91550 Dinkelsbühl
Tel. 09851/57 58 0
Fax 09851/57 58 59
E-mail: service@rommelsbacher.de

Internet: www.rommelsbacher.de

References

• Startseite - ROMMELSBACHER ElektroHausgeräte GmbH

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>