MAIRDI M9101 DECT Headset User Guide

MAIRDI M9101 DECT Headset

Packing Contents

• Charging Base x 1
• Headset x 1
• Power Adapter Cable x 1
• Telephone Cable x 1
• EHS Cable x 1 (Optional Accessories)
• USB Data Cable x 1

Headset Button Introduction

Speaker volume

| “Toot” once
Minus Button|

Volume down

| Tap the Minus button to decrease the

Speaker volume

| “Toot” once

Mic Mute

|

Mic mute

| Press the mute button to activate mic mute during a call, repress the mute button to

cancel mic mute.

| “Toot” every 3 seconds while

mute

Multi-function Button

| Power On/Off| Press the button for 5 seconds until

colorful ring light is on

|
Answer

/end call

| Tap the Multi-function button to

answer/end calls

|

Charging Base Introduction

Charging Base Introduction

Microphone & Outer Ringer Volume +/-

| Adjust microphone volume when on call. Press “+”or “-“button on headset base to

increase or decrease volume.

Adjust ring tone volume when the headset is in idle state. Press “+”or “-“button to hear ring tone, then press “+”or “-“button

to adjust volume.

Telephone Compatibility Switcher

| 7 kinds of compatibility setting for different IP phones, slide the switch button among A and G to choose correct compatibility for

your IP phone

Computer Button

| Tap the Computer Button to switch connecting device from telephone to PC

while the headset is in charging or idle state

Long press the Computer Button to pairing headset, the blue ring light flashes when

the headset is pairing mode

VoIP Button

| Tap the VoIP Button to switch device

connecting from computer to telephone when the headset is in charging or idle state

Long press the VoIP button to find the paired headset. The ring light of paired headset will flash red and green alternately with a beep

sound (for 20s)

Handset & Headset Switcher| Switch call between headset and handset

Details of 7 Positions of the Telephone Compatibility Switcher

Switch P osition| T e l ephone J ack Wiring| Matching T elephones( I ncluding but not limited)
---|---|---
A| M-,R , R,M+| Aastra , Alcate l , Fanvil , H tek, Gigaset, Mitel, N orte l , Sieme n s , S n om , Po l ycom. ..
B| R ,M – ,M+ , R| AVA Y A Ca ll mas t e r V a n d V l ,C i sco IP p h ones 79xx series . . .
C| M + , R , R , M­| Gra n ds tr eam , Yea l ink , Sangoma. ..
D| R,M+ , M- , R| Asco m office and P h ilips pho n es. ..
E| R, R ,M+,M ­| Plantronics Vista Base
F| R, M -, M+ , R| AVAYA Ca ll maste r V a n d V l ,Cisco I P p h o n es 79xx series . ..
G| R , M+ , M- , R| Asco m office and Phi lips pho n es . ..

Charge Headset : Place the headset on the charging base, align the charging port on headset with the charging pole on headset base unit

Status Indicators Introduction

continuously on
Headset on Call (on Charging Base)| Blue ring light on headset is continuously on
Headset ON/OFF| Colorful running ring light is on

Switch to Computer Connection

| Green light of computer button is continuously on
Switch to Telephone Connection| Green light of VOiP button is continuously on

Power On and Pairing

1. Connect the power adapter cable to headset base unit

2. Turn on the headset
   Press and hold the multi-function button till the colorful running ring light is on and then release, the green light will be continous on {the light will be off after 1 Os when it enters into idle state)

3. Pair the headset with base unit

4. Long press the computer button until the call status indicator flashes blue

5. Long press the headset microphone mute button until the ring light flashes green, wait a few seconds, the pairing is successful when both indicator lights are off.

Connecting Instruction

Connect headset with desk phones having handset

1. Step 1: With telephone cord included in your phone system, connect telephone socket on headset base unit to headset port on desk phone
2. Step 2: Connect the other end of handset cord to the handset port on headset base unit

Connect the headset with desk phone without handset:

With telephone cord, connect telephone port on headset base unit to headset port on telephone

Connect headset and telephone with EHS cable:
EHS cable enables remote answer or end call by using multi-function button on headset.
Refer to EHS Cable Installation Guide.

Very Important : After connecting the headset with your telephone, please slide the telephone compatibility switcher to test out the best position for best performance of headset speaker and microphone.

Connect headset with computer

1. Step 1: Connect the type C USB data cable to USB port on headset base unit
2. Step 2: Connect the USB-A USB data cable to USB port of computer

Troubleshooting

1. The headset cannot pair with base unit Make sure to press the computer button firstly, then press the headset microphone mute button after the call indicator on headset base unit flashes. It is an important sequence to pair successfully.
2. Low microphone volume
3. Check the microphone is not muted.
4. Check the position of microphone is 2 fingers away from your lips.
5. Adjust the microphone volume on headset base unit.

Cautions

1. Please keep the headset battery safely. Do not put the battery into water or fire to avoid explosion
2. Please use the headset volume at a moderate level. Do not use the headset with high volume for extra long time, which may cause hearing loss.
3. Do not charge the headset with high voltage device, which may cause damage to it.

Product Warranty Card

Customer Name| Product Model No.|
---|---|---
Date of Purchase| I Tel No.IE-mail:|
Problem Description:|
Microphone|  | I Speaker| I Battery| !Buttons

Warranty:

Failure of headset buttons, speaker or microphone; charge unavailable. Out of Warranty:

1. Ear cushions broken.

2. Fail to follow the user manual or disassemble the headset.

3. Incorrect connection with high voltage device for charging which causes earphone damage.

4. Artificial damage caused by impact, falling, water, pulling.

OQC

CHECKING

| I| (QC2|  |

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. (For Base) The device has been tested and comply with FCC SAR limits.(For handset)

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>