MAIRDI M100V Wireless Bone Conduction Headphone User Manual

June 13, 2024
MAIRDI

MAIRDI M100V Wireless Bone Conduction Headphone

PRODUCT INFORMATION

MODEL NO.: M100V

Quick Start

Correct Wearing

Power On/Off

Connect with Mobile Phone

  • After powered on, the headset will go into pairing mode
    • Blue and red light flashes alternately
    • Pairing
  • Turn on the Bluetooth function on the mobile phone and search M100V
    • Blue breath light flashes once every 10 seconds
    • Connected

Connect with Two Mobile Phones

  • Turn off the Bluetooth function of the first mobile phone which was paired with “M1 OOV” already.
  • Turn on the second mobile’s Bluetooth function and search “M 1 OOV” for pairing.
  • Turn on the first mobile’s Bluetooth function. Search and connect the “M100V” paired before.

Playing/ Pause


  • Short press once to pause
  • Short press once again to play
    When playing music blue breath light flashes every 10 seconds

Next/ Last Song & Volume Adjustment /Mic Mute

  • Long press the “volume -” button 2ss to mute the microphone during the call. The “Toot” tone will be heard every 1 Oss while the microphone muted.
  • Long press the same button 2ss again to un-mute microphone
    Toot

Call Management

  • When a call is coming, red light flashes every 3 seconds
  • During the call, blue light flashes every 10 seconds

Voice Assistant

  • Available to wake up voice assistant by touching the multi-function button for 4ss when connected to a cell phone (not in music mode).
  • Pause music to wake up the voice assistant if in music mode.

Factory Reset

  • Blue and red light flashes alternately
    Toot

Charging

  • A red light flashes when the battery low
  • Prompt tone “didi” every 10 seconds
  • Solid red light when charging, solid blue light when fully charged

Accessories

  • Headset: 1

  • Charge Cable: 1

  • User Manual: 1

  • Silicone Earplugs: 2

  • Velvet Bag:  1 Specifications

  • Model No.: M1 OOV

  • Bluetooth Version: 5.1

  • Bluetooth Protocol: A DP, AVRCP, HFP, AAC, etc.

  • Transmission Distance: 30m(without obstacle)

  • Weight: 40g

  • Audio Channel: Stereo

  • Speaker Frequency : 50HZ-20KHZ

  • Sound Quality: APTX-HD/no distortion

  • Microphone: AI dual-mic noise reduction technology

  • Standby : 200H

  • Music Time: 8H(70% volume)

  • Charge Time : 1.5H

  • Charge Voltage: 5VDC(S24V}

  • Charge Port: Type-C USB

  • Battery Capacity: 180mAh

  • Working Temperature: -10 C-60 C

  • Battery Charge Time: > 1000

  • Waterproof Level: IP65

Note:

  1. The correct wearing position of the bone conduction speaker of this headset is the cheekbone in front of the ear. Please do not put the speaker into your ears.
  2. Listening to high-volume music for a long time may cause hearing loss. Please try to listen at a moderate level of volume.
  3. Avoid dropping from high which causes damage to sound quality. Keep away from fire and high-voltage equipment.
  4. Please store the headset in a dry and ventilated place. When the headset is not used for a long time, charge it every two months
  5. If the headset is stained with water or sweat after exercising, please use a clean cloth to wipe it for long-term use.
  6. Please reset the headset if it cannot work well,
  7. Please check the charging port before charging to make sure there are no water stains or foreign matters.

Warranty Card

Warranty Coverage
Button failure, no sound from speaker or microphone, The  call does not work, unable to charge normally

Warranty service

  • Damage caused by negligence.
  • Damage caused by unauthorized disassembly and modification.
  • Damage caused by charging with high voltage or manual abuse.

CHECK OUT CARD

Checker:

This device complies with part 1 5 of the FCC Rules. Operation is subject to the following two conditions:

  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and the receiver.
  • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.
  1. The device has been evaluated to meet general RF exposure requirements.
  2. The device can be used in portable exposure conditions without restriction.

FCC ID : 2ARQZ-M100V

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals