CONAIR GMT10RCSB All-in-One Beard Mustache Trimmer Instruction Manual
- June 6, 2024
- ConAir
Table of Contents
CONAIR GMT10RCSB All-in-One Beard Mustache Trimmer
Instruction Booklet
For your safety and continued enjoyment of this product, always read the
instruction booklet carefully before using.
TRIMMING YOUR MUSTACHE
-
For best results, start with a clean, slightly damp mustache.
-
Comb through your mustache in the direction it grows.
-
Place the 5-position comb over the facial hair blade and snap it into position. It is a good idea to start with the longest trim setting adjustment. (You can always go back and cut your mustache more closely with a shorter setting.) Always trim your mustache from the top down.
-
After your mustache has been trimmed to the desired length, remove the 5-position comb and, using the blade only, define the outline of the bottom of your mustache.
ON/OFF SWITCH
To operate, simply slide switch toward blade; to stop, slide switch away
from blade.
CARE OF YOUR TRIMMER
REPLACEMENT (REMOVAL) OF BLADE SET
To remove blade set from your trimmer, make sure the trimmer is in the OFF
position. Remove the blade set by placing thumb against the smaller cutter and
pushing for-ward, releasing the cutter assembly from the trimmer housing.
Replace with new cutting system and reverse the removal procedure, only this
time place your thumb on the large cutter and snap into place.
BATTERY REMOVAL
- Using a small Phillips head screwdriver, remove the screws at the back of the trimmer.
- Remove the bottom housing and cut the battery out. Bring the battery to the nearest collection center for proper disposal. DO NOT throw the battery into the normal municipal waste system.
CONTAINS NICKEL METAL HYDRIDE BATTERY.
MUST BE COLLECTED, RECYCLED OR DISPOSED OF PROPERLY. DO NOT DISPOSE OF IN THE MUNICIPAL WASTE.
MODEL GMT10RCSB
BEARD/MUSTACHE TRIMMER
LIMITED TWO-YEAR WARRANTY
Conair will repair or replace (at our option) your unit free of charge for 24 months from the date of purchase if the appliance is defective in workmanship or materials.
To obtain service under this warranty, return the defective product to the
service center listed on back, together with your purchase receipt and $3.00
for postage and handling. California resi- dents need only provide proof of
purchase and should call 1-800-366-0937
for shipping instruc- tions. In the absence of a purchase receipt, the
warranty period shall be 24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITIES, INCLUDING BUT NOT LIMITED
TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED IN DURATION TO THE 24-MONTH DURATION OF THIS
WRITTEN, LIMITED WARRANTY. Some states do not allow
limitations on how long an implied warranty lasts, so the above limitations
may not apply to you.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR
IMPLIED, WHATSOEVER. Some states do not allow the exclusion or limitation of
special, inci- dental, or consequential damages, so the above limitation may
not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, especially when children are present, basic safety precautions should always be taken, including the following:
READ ALL INSTRUCTIONS BEFORE USING
FOR HOUSEHOLD USE ONLY
KEEP AWAY FROM WATER
DANGER – Any appliance is electrically live, even when the switch is off.
To reduce the risk of death or injury by electric shock:
- Always unplug appliance from electrical outlet immediately after using (except when charging unit).
- Do not place or store appliance where it could fall or be pulled into a tub or sink.
- Do not use appliance while bathing or in the shower.
- Do not place appliance in, or drop into, water or other liquids.
- If appliance has fallen into water, do not reach for it. Unplug immediately.
- Unplug this appliance before cleaning.
WARNING – To reduce the risk of burns, electric shock, fire, or injury to persons:
- Never leave a plugged-in appliance unattended.
- This appliance should not be used by, on, or near children or individuals with certain disabilities.
- Use appliance only for its intended use as described in this manual. Use only attachments recommended by the manufacturer. Do not use an extension cord to operate the appliance.
- Never operate the appliance if it has a damaged cord or plug, is not working properly, has been dropped or damaged, or dropped into water. Return the appliance to a Conair Service Center for examination and repair.
- Keep the appliance cord away from heated surfaces.
- Do not pull, twist or wrap the cord around the appliance.
- Never drop or insert any object into any opening of the appliance.
- Do not place the appliance on any surface while it is operating.
- Do not use the appliance with a damaged or broken comb or with teeth missing from the blades, as injury may result. Before each use, make certain the blades are aligned properly and oiled.
- Do not use the appliance outdoors or where aerosol (spray) products are being used or oxygen is being administered.
OPERATING INSTRUCTIONS
Before using the Class 2 Power Supply, read these instructions carefully.
Use with adapter CA51
Rated input voltage: 100–240V AC, 50/60Hz
0.2A Max
Rated output: 6.0V DC 70mA
OPERATION
- For dry location use only. Do not expose to water.
- When not in use, unplug unit completely.
- Unit will become warm during operation.
CAUTION
- Dry location use only. Do not expose to liquid, vapor, or rain.
- Ensure jack is plugged into the trimmer unit before plugging the adapter into the outlet.
- Do not operate any appliance that has a damaged output cord or housing.
- Always unplug the unit before cleaning or when not in use.
- This power unit is intended to be correctly oriented in a vertical or floor mount position.
- Be sure voltage is correct before plugging in.
For connection to a supply not in the U.S.A. use an attachment plug adapter of the proper configuration for power outlet.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modification to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
TROUBLESHOOTING
If your rechargeable trimmer does not seem to be taking a charge, take the following trouble- shooting steps before returning it for repair:
- Be sure the electrical outlet is working by plugging in another appliance to test the outlet.
- Make sure the electrical plug is not con- nected to a switch that turns power off when lights are turned off.
- Be sure you have inserted the adapter prop- erly into the trimmer, that all connections are secure, and that the trimmer switch is in the OFF position.
OPERATING INSTRUCTIONS
- Before using the trimmer for the first time, charge continuously for 16 hours. Maximum battery capacity will be reached only after 3 charging and discharging cycles.
- Always check to see if the charging light is on when you firmly connect the unit with the adapter.
- Plug the adapter into any wall outlet (at the voltage listed on the label affixed to the adapter). Unplug adapter when not in use.
- The adapter may become warm while charging. This is normal.
- Preserving the batteries: in order to maintain the optimum capacity of the rechargeable batteries, the trimmer should be recharged for 16 hours approximately every 3 months.
USER MAINTENANCE INSTRUCTIONS
OILING THE BLADE (oil not included)
About once a month you should oil the trimmer blade with a light mineral oil.
It is best to do this over a piece of newspaper. Turn the trimmer on and hold
it so that the blades are pointed down- ward. Spread one drop of oil across
the blades, then turn the trimmer off and wipe away the excess oil with a soft
cloth.
Be careful not to use too much oil and don’t oil your trimmer more than
necessary, as this could damage the motor. (Never attempt to oil the motor
bearing, as it is permanently lubricated.)
BLADE CARE
Because the trimmer blade is precision-made for a very special use, it should
always be handled with care. Each time you finish using the trimmer, brush
away any loose hair that has collected in the blade. Be especially careful
when changing or adjusting the blade. When you have your trimmer serviced, be
sure that the blade is sharpened or replaced at the same time.
To promote the long life of the trimmer, use it only for the purpose intended
by the manufacturer – to trim your beard and mustache.
GROWING A BEARD AND MUSTACHE
There are three key factors that will determine which beard or mustache style
is best for you:
- The shape and dimensions of your face.
- The natural growth of your beard/mustache.
- The thickness of your beard/mustache. If you are unsure about the type of beard or mustache that would most suit your face, speak with a professional hair stylist and ask for an opinion on what style would be best. Once your beard or mustache has been styled, it is essential that you maintain its appearance. To do this, use your trimmer to trim your beard/mustache weekly.
For the best trimming results, your beard should be slightly damp (NOT WET) when using your trimmer. This will prevent the trimmer from removing more hair than desired.
TYPES OF BEARDS/MUSTACHES
GETTING STARTED
OUTLINING YOUR BEARD
- It is always best to begin with a clean, slightly damp beard.
- After you have combed through your beard in the direction it grows naturally, you will want to outline the desired shape, beginning under your jawline.
- Begin defining your beard’s shape under your chin and work upward on each side of your face toward your ears. Then define the upper outline of your beard across your cheeks, past your sideburns, and toward your hairline.
TRIMMING YOUR BEARD
-
The trimmer includes a 5-position comb for use with the hair trimming blade (2–10mm) which provides lengths of 3/32″ (shortest) to 3/8″ (longest).
-
To use the 5-position comb, slide the unit over the trimmer blade and snap it down into position. At first, until you become familiar with the adjustments, use the longest trim setting. (You can always go back and make your beard a little shorter.)
-
Begin trimming your beard using smooth, even strokes. Start with your sideburns and work downward toward your chin. (Never attempt to trim against the natural growth of your beard because the hair will be cut too short.)
-
If you decide you want a closer trim, you can now adjust the 5-position comb attachment to a shorter setting (such as 3/32″ or 5/32″) and go over your beard again until you achieve the desired length.
BLENDING THE JAWLINE
- Two all-purpose attachments, AC14, which provides lengths of 3mm (shortest) and AC13, which provides lengths of 5mm (longest), will help you to achieve a neat, finished trim under your chin. To use one of the attachments, press it down over the trimmer blades until it clicks into position.
- Hold the trimmer in an upright position and begin trimming under your jawline, using short, even strokes.
- After your beard is blended, turn off the trimmer and remove the attachment by gently pulling up on tab.
Please register this product at:
www.conair.com/registration
©2013 Conair Corporation
Service Center
Conair Corporation
Service Department
7475 North Glen Harbor Blvd.
Glendale, AZ 85307
TRIMMER REPLACEMENT PARTS & ACCESSORIES ORDER FORM
Pricing in effect through June 1, 2015. Orders postmarked after this date will
be accepted, and the customer will be notified if pricing has changed.
Enclose check or money order made payable to Conair. (We cannot accept cash,
stamps or C.O.D. orders.) *CT, IL, AZ, and PA residents should add applicable
state sales tax. Minimum order of $10.00 or a $2.00 handling charge will be
added to order.
All prices include handling and return postage.
Prices are subject to change without notice.
Prices are valid only for shipments within the continental United States.
Please allow 4–6 weeks for delivery.
To avoid delays, please print clearly.
We must have a street address, as UPS cannot deliver to a P.O. box.
Documents / Resources
|
CONAIR GMT10RCSB All-in-One Beard Mustache
Trimmer
[pdf] Instruction Manual
GMT10RCSB, All-in-One Beard Mustache Trimmer
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>