FLYINGVOICE G504 4 FXS Gigabit VoIP Adapter Installation Guide
- June 3, 2024
- FLYINGVOICE
Table of Contents
G504 4 FXS Gigabit VoIP Adapter
Installation Guide Quick Installation Guide
– Gateway Series
G504 4 FXS Gigabit VoIP Adapter
If you configuring your device for the first time, you will find the steps included in this quick install guide useful. Once you have configured the device with your settings, you will need to reboot the device for your changes to be applied. If you require additional information, please download the latest product manual from our webstie at www.flyingvoice.com..
Packaging Contents
The following items are included in your package. Please contact your service provider, if you find anything missing.
Startup
Connect the WAN port of your device to your router or PBX and the LAN port to
your PC. Also connect your analog phone(s) to the phone
ports(s).:Notice: Do not disconnect the power adaptor
from the device while configuring or updating the firmware on the device.
Ensure that you always use the power adapter included in the package to power
your device. Using a different power adapter may damage the device.
LEDs :
After the hardware connections have been completed, check the status of the
LED indicators using the following table:
LED | Status | Description |
---|---|---|
Phone | On | Registered successfully or no call |
Blinking | Offhook or in a session | |
Off | Ungregistered | |
WAN | On | The data is transmitting |
Blinking | The port is disconnected | |
Off | The port is connected | |
POWER | On | The gateway is powered on and running normally |
Blinking on 10Hz | Firmware Upgrade | |
Off | The gateway is powered off | |
WAN | On | The port is connected |
Blinking | The data is transmitting | |
Off | The port is disconnected |
Network Configuration
In the browser of your PC connected to the LAN port of the device, type
“http://192.168.1.1” and press the “Enter” key. A Username and Password dialog
box will appear. To login as an Administrator enter “admin” as the username
and “admin” as the password. To login as a normal user enter “user” as the
username and “user” as the password.
“In the event you are uable to open the page
http://192.168.1.1 with your browser, it might be because
of an network conflict with the WAN IP. In that case, open the page
http://192.168.2.1 instead.”
- DHCP is the most common method where the ISP automatically configures your Internet connection.
- Choose “Static” if you know the network connection settings of your ISP. Fill in the IP parameters provided by your ISP.
- If your ISP uses PPPoE they will provide you a username, password, and instructions.
Notice : In the event you are uable to open the page http://192.168.1.1 with
your browser, it might be because of an network conflict with the WAN IP.
In that case, open the page http://192.168.2.1 instead.”
Phone Registration
Click the ‘FXS1’ tab to begin configuring the first SIP account for your
device.
First set the field ‘Line Enable’ to “Enable”, then enter the SIP registration
parameters provided to you by your phone provider as show in the ‘Proxy and
Registration’ and ‘Subscriber Information’ section.Follow the same process to configure the other SIP accounts.
Parameters Name | Description |
---|---|
Line Enable | If or not enable Line |
Proxy Server | The domain neme or IP address of SIP server |
Outbound Port | Outbound Proxy IP or domain name |
Proxy Port | Outbound Proxy’s Service port |
Outbound Proxy | The port which SIP Server supports for VOIP service, default |
is 5060
Display Name| The number will display in callee
Phone Number| Number of telephone provided by SIP Proxy
Account| SIP account provided by SIP Proxy
Password| SIP password provided by SIP Proxy
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>