Onlywell WT1208 Smart Wi-Fi Clock User Manual
- June 5, 2024
- Onlywell
Table of Contents
WT1208 Smart Wi-Fi Clock
User Manual
WT1207product picture
Note: The operation methods of the 1208 and 1207 models are the same, and the 1208 models do not have the LCD screen display function.
Back button Description
LED Display description
- Date display
- Date format: MD /DM switch display
- Temperature: °C/°F switch display
- WIFI signal indicator icon
- DST icon
- Low battery icon
- Week: 7 language switching display
Quick setup guide
Step 1: Insert the battery or press the “WIFI” button
to turn on the WIFI power The LED light starts to flash.| Step 2: Open the WLAN
settings menu of your phone or compute
---|---
|
Step 3: Find the network of “WIFIClock_xxxx”, press
the “Connect” button| Step 4: Open the browser, and enter in the address bar:
“192.168.4.1”. Example: Chrome, Firefox
|
Step 5: Press “Network” to enter the network menu.
Wait for the device to scan for connectable router signals.| Step 6:Pull down
the “Route” list and look for the route name to be connected.
If not found, you can click the “Refresh” button or manually enter it in
“AddRoute”
|
Step 7: Enter the password for this route and press the “Connect” button| Step
8: Wait for the “Network Connection Succeeded” prompt
This may take 10 seconds or more
|
Step 9: Press and enter the “Time” settings menu| Step 10: Pull down to select
the time zone and press the “Setting time” button to complete the setting.
| 
Basic operation
-
Insert the battery or press the “WIFI” button to open the WIFI power supply and WEB service.
The WIFI icon starts to flash, indicating that the network is being connected.
When the WIFI icon is displayed long, it indicates that it is connected to the network.
If WIFI is not connected to the network, the WIFI icon will disappear. -
When the WIFI power is turned on, press the “WIFI button to turn off the WIFI power and WEB service.
-
Press the “WIFI” “Reset” button or press the “WIFI” button to install the battery and restore the factory settings.
-
Press “C/F” to convert the temperature unit °C/°F
Note:
Insert the battery and turn on the WIFI power for 10 minutes.
Press the “WIFI” button to turn on the WIFI power for 5 minutes.
LED status
- LED flashing: WEB service is already open, WIFI is connecting route,
- LED is on: WEB service is already on, WIFI is connected to the route
- LED off: Turn off WIFI power and WEB service.
- LED flashes quickly: Restore factory settings.
- The LED flashes once every 10 seconds: The battery is low.
Other
- Automatic timing: It is randomly open every hour between 19:00 and 22:00 every day. After the calibration is successful, it will not be calibrated again until after 19:00 on the second day.
- Automatic stop seconds mute: The default is 22:00-6:00, the default setting can be changed through WEB
- Temperature range： -9.9℃~50.0℃
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by
the manufacturer could void your authority to operate this equipment.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
WEB Service Manual：
open your phone WLAN page
Press and hold the WIFI button on the device for 2 seconds to turn on the WLAN
function of the device.
Main Menu
Network Menu
Time Menu
System Menu
VIDEO TUTORIAL
https://www.youtube.com/watch?v=_TF7K2v5zJc
Video tutorial
https://youtu.be/_TF7K2v5zJc
CORPORATE NAME：
Shenzhen Henghuida Electronics Co., Ltd.
ADD:
Floor 3, Building A, Yongchuang Science, and Technology Park, Fenghuang Road,
Dalang Street, Longhua New District, Shenzhen
Tel: 0755-27743720
Web:http://onlywell.com.cn