CREATE Stylance Top Fridge Freezer User Manual

**CREATE Stylance Top Fridge Freezer User Manual

**

Thank you for choosing our fridge and freezer. Before using this appliance and to ensure its best use, please read the instructions carefully. The safety precautions listed here reduce the risk of fire, electric shock, and injury when followed correctly. Keep the manual in a safe place for future reference, as well as the warranty, purchase receipt and box. If applicable, give these instructions to the future owner of the appliance. Always follow basic safety instructions and risk prevention measures when using an electrical appliance. The manufacturer will not be held responsible for any damage resulting from the user’s failure to follow these instructions.

LIST OF PARTS

1. Freezer glass shelf
2. Thermostat
3. Fridge glass shelves
4. Vegetable cover
5. Crisper
6. Door shelves

SECURITY INSTRUCTIONS

When using any electrical appliance, the following basic safety precautions should always be observed.

• This type of refrigerator is widely used in places such as hotels, offices,  student dormitories,and homes. It adopts high efficiency compressor and classic structural layout. Enjoy the advantages of low electricity consumption, freezing capacity and ease of use. It contains a refrigerator compartment and a freezer compartment. Caution: When defrosting, never use sharp or metal objects to remove frost on the evaporator surface, as this will damage the evaporator.
• Do not store the bottled drink in the freezer compartment, to prevent it from breaking and damaging the refrigerator.
• If you are going to use it intermittently, keep it plugged in each time for periods longer than ten minutes.
• It should be verified that the voltage used is the same as the rated voltage before using the refrigerator.
• The power plug should have its own separate power outlet to prevent the power cord from being overheated by other plugs.
• Do not splash water on the refrigerator. Otherwise, it may cause the refrigerator to malfunction or electric shock.
• Do not store flammable materials such as alcohol, gasoline, LP gas and glue in the refrigerator.
  WARNING: Food should not be stored in the freezer in contact with the wall. When the surface of the evaporator freezes, it creates a thin layer of ice that would turn anything in contact with this part of the freezer into a block of ice, which would also hinder the correct operation of the product.

INSTALLATION

1. After transportation, make sure the refrigerator is in an upright and level position for 12 hours to allow compressor fluids to redistribute evenly before use. Do not tilt the refrigerator more than 45° upright when moving it. Do not apply force to any part such as the condenser, door and its handle to prevent the refrigerator from being deformed, or its performance will be affected.
2. Make sure there is enough space around the refrigerator for it to work well.
3. The refrigerator should be kept away from high temperatures, heat sources, water sources, sunlight or humid conditions.

HOW TO USE

1. The moment you connect the refrigerator correctly to the power supply, the compressor will automatically turn on and start cooling. Let it cool down, adjust the  thermostat to level 3, for at least 4 hours. Then adjust the thermostat dial to the desired setting and place the food in the refrigerator.
2. The refrigerator temperature can be adjusted by turning the thermostat. Setting the thermostat dial to 3 – 4 is best for general operation. When the thermostat number is larger, the cooling capacity is stronger.
3. Don’t put too much food in the refrigerator. Open the door less to maintain the temperature of the refrigerator and save on electricity consumption.
4. When making ice cubes, fill the ice cube tray with drinking water and put it in the freezer. It takes about 2-3 hours to make ice cubes. Ice cubes can be removed by rotating the ice tray, but do not twist it up and down; otherwise it might break.
5. Defrost the freezer whenever the layer of frost on the surface reaches 3 4mm. When defrosting, remove all food, set the thermostat to 0 position, unplug the refrigerator and open the door. After the frost has melted, discard the water and dry the inside of the refrigerator. It can then be reset by connecting to power and turning your thermostat to the desired setting. Wait at least 2 hours for the interior to cool down sufficiently. Put the food back inside.

CLEANING AND MAINTENANCE

• When you clean the refrigerator, unplug the power cord. Gently rub with a cloth soaked in mild soap, then remove. For proper cleaning, a sponge, towel or soft brush is recommended.
• Never use abrasives, or corrosives, steel wool, scouring pads, chemical cleaning agents or highly scented cleaning products to clean the interior, gasoline or other flammables to clean the refrigerator because they can damage the appliance and leave a bad smell.

PROBLEM RESOLUTION

• power is supplied and the voltage is normal,
• the fuse is not blown,
• the power plug is firmly inserted into the socket.

The refrigerator is not cold enough.| Make sure that:

• the thermostat is in the correct setting,
• there is enough space around the refrigerator,
• the door is not opened too often or for a long time,
• the refrigerator is not exposed to direct sunlight or placed near a heat source,
• there is not too much food or hot food in the refrigerator.
• Try letting the refrigerator cool down for at least 4 hours after it is turned on.

Food freezes in the refrigerator| Make sure that:

• the thermostat is in the correct setting,
• there aren’t too many.

The refrigerator makes too much noise.| Make sure that:

• the refrigerator is well leveled,
• the refrigerator does not touch objects around it,
• solid containers or packages stored inside do not touch each other.

During periods of high humidity, moisture can form on the surface of the refrigerator. It is not a malfunction. You can clean it yourself. If your refrigerator still does not work properly after performing the above checks, please contact the maintenance service department a soon as possible.

 In compliance with the directives: 2012/19/EU and 2015/863/EU on the restriction of the use of hazardous substances in electrical and electronic equipment, as well as their waste disposal. The crossed bin symbol shown on the packaging indicates that the product at the end of its useful life will be collected as separate waste. Therefore, any product that has reached the end of its useful life should be delivered to waste disposal centers specialized in the separate collection of waste electrical and electronic equipment, or returned to the retailer when purchasing similar new equipment, in one for a base. Proper separate collection for subsequent commissioning of equipment sent for recycling, treatment and disposal in an environmentally compatible manner helps prevent possible negative effects on the environment and health and optimizes recycling and reuse of waste. the components that make up the device. The abusive disposal of the product by the user implies the application of administrative sanctions in accordance with the laws.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>