STEINEL PC4-DALI-2 Tasterkoppler Accessories Pushbutton Coupler User Manual

: June 5, 2024
: STEINEL

STEINEL PC4-DALI-2 Tasterkoppler Accessories Pushbutton Coupler

About this document

Under copyright. Reproduction either in whole or in part only with our consent.
Subject to change in the interest of technical progress.

Hazard warning!
Warning of hazards from electricity!

General safety precautions

Failure to observe these operating instructions presents hazards!

These instructions contain important information on the safe use of this product. Particular attention is drawn to potential hazards. Failure to observe this information may lead to death or serious injuries.

Read instructions carefully.
Follow safety advice.
Keep instructions within easy reach.
Working with electrical current may produce hazardous situations. Touching live parts can result in electrical shock, burns or death.
Work on mains voltage must only be performed by qualified, skilled personnel.
National wiring regulations and electrical operating conditions must be observed (e.g. DE: VDE 0100, AT: ÖVE-ÖNORM E8001-1, CH: SEV 1000).
Only use genuine replacement parts.
Repairs must only be carried out by companies qualified to do so

System description

Proper use

Interface for standard switches.
Suitable for installation in a concealed box with a minimum depth of 60 mm.

Non-intended use

The terminals on the switch coupler are not suitable for mains voltage.

Operating principle

The switch coupler integrated additional switched into a DALI lighting system.
Up to four standard switches can be connected to each switch coupler.
The switch coupler relays the signals to the application controller (APC) / control unit via DALI.
The switches can be programmed to function in any chosen way at the time they are put into operation.

Package contents

1 switch coupler
1 safety data sheet
1 quick-start guide

Product dimensions

Product components

A Switch terminals
B DALI-2 input

Electrical connection

Wiring diagrams

The mains supply lead is a multiple-core cable:
L = phase conductor (usually black, brown or grey)
N = Neutral conductor (usually blue)
D A+ = connection to the DALI BUS (brown)
DA- = connection to the DALI BUS (brown)

Switch channels / supply:
K1 = channel 1
K2 = channel 2
K3 = channel 3
K4 = channel 4
COM = switch supply

Switch cable

No longer than 50 cm.
Must be laid in a separate plastic-sheathed conduit.

Installation

Hazard from electrical power.

Touching live parts can result in electrical shock, burns or death.

Switch OFF power and interrupt power supply.
Using a voltage tester, check to make sure that the power supply is disconnected.
Make sure power supply remains interrupted.

Risk of damage to property!

Mixing up connection leads may produce a short circuit.

Identify connection leads.
Connect the leads correctly

Preparing for installation

Check all components for damage. Do not use the floodlight if it is damaged.
Familiarise yourself with the fitting situation and the relevant documentation.
Select an appropriate site to install the product.
– Vibration-free.
– Not in explosive atmospheres.
– Not on normally flammable surfaces.
Put together the tools and material needed:
– Screwdriver.

Installation procedure

Example application: 1 switches

Make sure the power supply is switched OFF.
Connect mains power supply lead as shown in the wiring diagram.
➔ „4. Electrical connection“

Example application: 2 switches

Make sure the power supply is switched OFF.
Connect mains power supply lead as shown in the wiring diagram.
➔ „4. Electrical connection
Fit switch coupler into the box.
Fit switch onto the box.

• Switch ON power supply.

Cleaning and maintenance

The tool requires no maintenance.

Hazard from electrical power.

Contact between water and live parts can result in electric shock, burns or death.

Only clean tool in a dry state.

Disposal

Electrical and electronic equipment, accessories and packaging must be recycled in an environmentally compatible manner.

Do not dispose of electrical and electronic equipment as domestic waste

EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment and its implementation in national law, electrical and electronic equipment no longer suitable for use must be collected separately and recycled in an environmentally compatible manner.

Conformity

STEINEL Vertrieb GmbH hereby declares that the PC4-DALI-2 switch coupler radio equipment type conforms to Directive 2014/53/EU. The full wording of the EU Declaration of Conformity is available for downloading from the following Internet address: www.steinel.de

Manufacturer’s Warranty

As purchaser, you are entitled to your statutory rights against the vendor. If these rights exist in your country, they are neither curtailed nor restricted by our Warranty Declaration. We guarantee that your STEINEL Professional sensor product will remain in perfect condition and proper working order for a period of 5 years. We guarantee that this product is free from material-, manufacturing- and design flaws. In addition, we guarantee that all electronic components and cables function in the proper manner and that all materials used and their surfaces are without defects

Making Claims

If you wish to make a claim, please send your product complete and carriage paid with the original receipt of purchase, which must show the date of purchase and product designation, either to your retailer or contact us at STEINEL (UK) Limited, 25 Manasty Road, Axis Park, Orton Southgate, Peterborough, PE2 6UP, for a returns number. For this reason, we recommend that you keep your receipt of purchase in a safe place until the warranty period expires. STEINEL shall assume no liability for the costs or risks involved in returning a product.

For information on making claims under the terms of the warranty, please go to www.steinel-professional.de/garantie

If you have a warranty claim or would like to ask any question regarding your product, you are welcome to call us at any time on our Service Hotline 01733 366700.

Technical specifications

– Dimensions (H × W × D):	49.8 × 43.0 × 15.1 mm
– Voltage range:	9.5 VDC – 22.5 VDC (in accordance with IEC62368-101)
– Typical DALI current consumption (at 16.5 V):	2.7 mA
Max. DALI current consumption (starting current at 22.5 V):	9 mA
– DALI-2 addresses:	1
– Input via:	floating push-button/switch
– Number of inputs:	4
– Input terminal labelling:	K1, K2, K3, K4
– Max. cable length:	50 m
– Max. housing temperature:	75 °C
– Protection class:	II. When used in the intended manner
– IP rating:	IP 20
– Ambient temperature:	-20°C to +50°C

Troubleshooting

Unit without power.

Fuse not switched ON or faulty.
• Switch ON fuse.
• Change faulty fuse.
Break in wiring.
• Check wiring with voltage tester.
Short circuit in mains power supply lead.
• Check connections.
Any mains switch OFF
• Switch ON mains switch.

STEINEL Vertrieb GmbH
Dieselstraße 80-84
33442 Herzebrock-Clarholz
Tel: +49/5245/448-188
www.steinel.de

Documents / Resources

| STEINEL PC4-DALI-2 Tasterkoppler Accessories Pushbutton Coupler [pdf] User Manual
PC4-DALI-2, Tasterkoppler Accessories Pushbutton Coupler, PC4-DALI-2 Tasterkoppler Accessories Pushbutton Coupler, Pushbutton Coupler, Coupler
---|---