GOODWE GW15K-ET Residential Smart Inverter Solutions User Guide
- June 1, 2024
- GOODWE
Table of Contents
- GOODWE GW15K-ET Residential Smart Inverter Solutions
- Product Usage Instructions
- Frequently Asked Questions
- Networking
- Power On/Off
- Installations
- Wiring Diagram
- Battery System Wiring Diagram
- Equipment Commissioning
- Setting Batteries Of Each Inverters (Only For Parallel Connections)
- Configuring the Network
- Creating a Power Plant
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GOODWE GW15K-ET Residential Smart Inverter Solutions
Specifications:
- Model: Residential Smart Inverter Solutions Quick Guide (ET15-30kW+Lynx Home F)
- Versions: V1.0-2024-03-30
- Inverter Models: GW15K-ET, GW20K-ET, GW25K-ET, GW29.9K-ET, GW30K-ET
- Battery System Models: Lynx Home F (G2), Lynx Home F (G1, G1 Plus+)
Product Usage Instructions
01 Networking
Communication Module: Ensure proper communication module installation for networking.
02 Power On/Off
Single Inverter: Follow the power on/off instructions specific to each inverter model. Parallel System: Connect a maximum of 4 inverters in a parallel system following the guidelines.
03 Installations
Refer to the provided wiring diagrams for different setups involving inverters, Lynx Home F, and battery systems.
04 Wiring Diagram
Follow the specified wiring diagrams for different configurations such as single inverter with Lynx Home F and GM3000 or parallel connected inverters with GM330.
05 Equipment Commissioning
Use SolarGo app or SEMS Portal app for equipment commissioning. Ensure the software version is compatible and follow the prompts for connection. Set safety code, inverter quantity for parallel connections, working mode, depth of discharge, charging mode, BAT connect mode, and other parameters as needed. Configure network settings using SolarGo app or SEMS Portal app based on the preferred method. Adjust advanced parameters like power limit function, DRED/Remote Shutdown/RCR settings, and more as required. Create power plants and add equipment via SEMS Portal app by entering accurate plant information.
Frequently Asked Questions
- Q: Can I connect more than 4 inverters in a parallel system?
- A: No, the maximum number of inverters allowed in a parallel system is 4 as per the specifications.
- Q: How do I know if my SolarGo app version is compatible for parallel scenarios?
- A: Ensure your SolarGo app version is 5.3.0 or above for parallel scenarios as mentioned in the instructions.
- Q: What is the default installer password for quick settings?
- A: The default installer password for quick settings is “goodwe2010”.
Residential Smart Inverter Solutions Quick Guide (ET15-30kW+Lynx Home F)
WARNING
The information in this quick guide is subject to change due to product updates or other reasons. This guide cannot replace the product labels or the safety precautions in the user manual unless otherwise specified. All descriptions in the manual are for guidance only.
Networking
| Device | Model | Description |
|---|
Inverter
| GW15K-ET GW20K-ET GW25K-ET GW29.9K-ET GW30K-ET| A maximum of 4 inverters can be connected in a parallel system.
Inverter firmware requirements for parallel connections:
• Consistent firmware version
• ARM version: 08(401) or above
• DSP version: 07(7068) or above
Battery system
| Lynx Home F (G2) LX F12.8-H-P20 LX F16.0-H-P20 LX F19.2-H-P20 LX F22.4-H-P20 LX F25.6-H-P20 LX F28.8-H-P20| Lynx Home F (G1, G1 Plus+) LX F6.6-H
LX F9.8-H LX F13.1-H LX F16.4-H
|
• A maximum of 8 battery systems can be clustered in a system.
• Do not mix connect battery systems of different versions.
Smart Me- ter
|
• GM3000
• GM330
| • GM3000: GM3000 and the CT, which cannot be replaced, are included in the inverter package. CT ratio: 120A/40mA.
• CM330: order the CT for GM330 from GoodWe or other suppliers. CT ratio: nA/5A.
• nA: CT primary input current, n ranges from 200 to 5000.
• 5A: CT Secondary input current.
| Device | Model | Description |
|---|
Commu- nication Module
|
• WiFi/LAN Kit-20
• Wi-Fi Kit
• Ezlink3000
| • Use WiFi/LAN Kit-20 or Wi-Fi kit for a single inverter. Upgrade the firmware of the inverter before replacing the Wi-Fi kit with a WiFi/LAN Kit-20 dongle.
• In parallel scenarios, the EzLink 3000 must be connected to the master inverter. Do not connect any communication module to the slave inverters. The firmware version of EzLink should be 04 or above.
Power On/Off
Single Inverter
Parallel System
Installations
Wiring Diagram
ET 15-30kW (single) + Lynx Home F + GM3000 + WiFi/LAN
ET 15-30kW (parallel connected) + GM3000 + Ezlink3000
ET 15-30kW (single) + Lynx Home F + GM330 + WiFi/LAN
ET 15-30kW (parallel connected) + GM330 + Ezlink3000
Battery System Wiring Diagram
Equipment Commissioning
In parallel scenarios, the software version of SolarGo app should be 5.3.0 or above. Follow the prompts to connect the device.
Quick Settings
Tap Home > Settings > Quick Settings to complete quick settings step by step. Installer password: goodwe2010
Setting the BAT Connect Mode
Setting the Working Mode
Setting Batteries Of Each Inverters (Only For Parallel Connections)
Follow the prompts to set the battery model and connection mode of each
inverter
Setting the Advanced Parameters
Tap Home > Settings > Advanced Settings to set the following functions.
Setting DRED/Remote Shutdown/RCR or Three-phase Unbalanced Output Function
(Optional)
Configuring the Network
Method I (RECOMMENDED): SolarGo app
Tap Home > Settings > Communication Setting > Net- work Settings to set
network parameters
Method II: SEMS Portal app
Follow the prompts to configure the network.
Creating a Power Plant
Create power plants and add equipments via SEMS Portal app.
- GoodWe Technologies Co., Ltd.
- No. 90 Zijin Rd., New District,
- Suzhou, 215011, China
- www.goodwe.com
- service@goodwe.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>