iDPRT Zeva 1966 Photo Printer User Guide

: June 3, 2024
: iDPRT

iDPRT Zeva 1966 Photo Printer

Product Introduction

iDPRT-Zeva-1966-Photo-Printer-
fig-1

Accessory List

AC Adaptorx1
Paper Tray x1
Micro USB Cablex1

Notes

Only for cameras that support PicBridge connection.
Purchase a Ribbon/ Paper Set separately.

Power On and Connection

Connect the power cord Insert the power cord into the power interface on the back of the printer.

Power on

Hold down the power button to turn on the printer. The yellow LED indicator is lighting, which indicates the printer is waiting for connection.

Download app

Scan the QR code below, or search “Heyphoto” in Google Play or App Store, to download the app, and choose the model “Zeva 1966”.

Loading the Ribbon

Open the ribbon compartment cover

Insert the new ribbon and make it click into place

Load the ribbon into the printer in the direction of the arrow marked on the ribbon until it clicks into place.
Close the ribbon compartment cover

Loading the Photo Paper

Open the covers of paper tray
First open the outer cOver D, then the inner cover.

Load the photo paper with glossy side face up
Note: Placing more than 18 sheets of paper may damage the printer or cause malfunction. Do not touch the glossy side, except for the non-printable area.

Close the inner cover of paper tray

Loading the Paper Tray

Open the paper tray compartment cover
Make sure the outer cover of paper tray is open
Load the paper tray to the printer
Please make sure to fully insert the paper tray into the compartment
(It slides about 2cm into the compartment.)

Replacing the Ribbon

Open the ribbon compartment cover
To remove the used ribbon, move the lock upward that it will be ejected automatically
Load the new ribbon and make it click into place, then close the ribbon compartment cover

Tips:

All the drawings of product and accessories in the quick start guide are for reference only.
Due to the updating and upgrading of the product, there may be some diferences between the actual product and the drawings, please refer to the actual product.
For more product information, please contact iDPRT customer service.

Instructions for Button Operation

Turn on the printer: hold down the power button for 3 seconds, the yellow LED indicator is lighting.
Turn off the printer: hold down the power button for 3 seconds and then release it, the LED indicator will be off.
Reset AP mode: in power-on status, hold down the power button until the blue LED indicator flashes three times, release the button and reset the Wi-Fi configuration;
after resetting, te LED indicator will turn white.

Instruction for LED Indicator

Working Position

Please place the printer on the desk or other flat and stable surfaces.
Leave some space (at least 10cm) behind the printer for paper out when printing.

Printing Wirelessly from Smartphones (AP Mode)

Please make sure that the LED indicator of the printer shows white all the time, or else hold down the power button to switch to the AP mode;
Open the Heyphoto app, click “Album”, select the images to print and then click “Next
Adjust the images in print preview and click the printer icon on the top right corner;
Select “Connect via printer hotspot ; wait for the Bluetooth searching until it
shows “Zeva 1966-XXXx” and click to connect; (XXxX is last four digits of Bluetooth
MAC address showed on the bottom of the printer)
After connecting, the printer will start to print the photo.

Printing Wirelessly from Smartphones (STA Mode)

Make sure the smartphone has been connected to the Wi-Fi hotspot;
Open the Heyphoto app, click “Album”, select the images to print and then click Next”;
Adjust the images in print preview and click the printer icon on the top right corner;
Select “Connect hotspot’; wait for the Bluetooth searching until it shows “Zeva 1966-XXxx” and click to connect; (XXXX is last four digits of
Bluetooth MAC address showed on the bottom of the printer)
Enter the passwords of Wi-Fi hotspot, click “Configure Wi-Fi” and the green LED indicator will flash slowly; (The time consuming of Wi-Fi
configuration is related to the actual Wi-Fi network, please wait patiently)
After connecting, the green LED indicator is lighting, and the printer will start to print the photo.

FAQ: If there is no connection, please try to restart.

Note: The above instructions take photo album printing for example, for LOMO, AR and Credentials printing, please experience on your own according to the guide of app.

Printing via USB from a Computer

Connect one end of the USB cable to your computer and the other end to the
Micro USB port on the back of the printer;
Turn on the printer
Download the printer driver from iDPRT website or the QR code below and install it on your computer
After connecting, you can print the photos from the computer.

Precautions

The best operating temperature is 0°C~40°C, if the environmental temperature is too high, the print quality may be affected.
Please do not use the unofficial adaptor, color ink and photo paper to ensure the print quality.
Do not touch the film of color ink and the glossy side of photo paper in case of fingerprints that may affect the print quality. During printing, the area around the thermal print head is very hot.
Do not touch it, as you could be burned. Do not pull out the photo paper by force during printing, or else it may damage the printer. Please remove the paper tray when it is not used for a long time, and close the covers of the printer and the paper tray to avoid dust entering.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interterence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular instllation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCC’ s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

FCC ID: 2AUTE-ZEVA1966

Disclaimer

Thank you for purchasing our product! By using this product, you hereby signify that you have read the Disclaimer and all warnings carefully and that you understand and agree to abide by the terms and conditions herein. The user should observe safe and lawful practices including, but not limited to, those set forth in this document. Our company therefore holds no liability for damages caused by force majeure, used by a third party, incorrect use, non- compliance with this user manual or intentional misconduct on the part of the user. Except for the scope prohibited by the applicable laws, the company is not responsible for any incidental, indirect, special or consequential damages, including but not limited to the loss of profits, income or data due to the violation of explicit or implied warranties or conditions mentioned in this user manual. Information in this user manual is for informational purposes only. It is subject to change without prior notice, due to the manufacturer’ s continuous development program. This document supersedes and replaces all information supplied prior to the publication hereof.

After Service

Please read the guide carefully before using the product and keep it properly.

iDPRT Photo Printer
Dimension: 180X 131x 62mm
Weight: About 1.0kg
Product Name: Photo Printer
Product Model: Zeva 1966
Input: 24V=2A
Operating Temperature: 5°C-35°C
Executive Standard: GB4943.1-2011, GB/T9254.1-2021, GB 17625.1-2012
Wi-Fi Connection: Wi-Fi lEEE 802.11b/g/n 2.4GHz
Manufacturer: Xiamen Hanin Electronic Technology Co., Ltd.
Add: No.96, Rongyuan Road, Tong’an District, Xiamen, China, 361100
Official Web: www.idprt.com
Customer Service Email 1: idprt@afterservice.vip
Customer Service Email2: technical@idprt.com