FENTON 351.183 CCTV Security 4 Cam Wireless NVR Kit User Manual

FENTON 351.183 CCTV Security 4 Cam Wireless NVR Kit

Statement

Thanks for purchasing our products, please contact us for any question or requirement. This manual is meant for the wireless network video recorder kit.

Safety Cautions

1. Please do not put any container with liquid on the device(like vase with water).
2. Please put the device at a ventilated place and prevent clogging the ventilation hole.
3. Please check the power voltage, to avoid any damage to device caused by wrong voltage.
4. The NVR should work under the technical standard temperature and humidity.
5. Please place the device horizontally and keep it away from sharp pounding environment.
6. Moisture and dust on the unit may cause short circuit, for long-term use, please remove the dust on the unit, connector by brush periodically.
7. Battery replacement yourself is not suggested, since incorrectly operation may cause burst. Please contact professional person for battery replacement.
8. Please install the device according to safety norms, you could take the national or local standard as reference.

Package Inspection

Please check the device and all accessories according to packing list. Please contact the distributor timely in case of any damage or lack of accessory.

Connection Diagram

Antenna Direction
Point the antenna of both camera and NVR upwards

Hard Drive Installation

Pre-installed 1TB HDD

Rear Panel Description

Turn on/off

Make sure the access AC voltage is stable during NVR configuration and use., then apply power to boot up the device, the [POWER] indicator will be on. When entering the system, it’s a normal status if the status indicator flashes.

Product Features & Specification

• Features
• 4CH real-time 720P wireless P2P NVR kit.
• 2.4GHz wireless transmission technology.
• SSID technology guarantees the safety of use.
• Auto code-matching realizes convenient real P2P application.
• Support HD 720P wireless IP camera.
• Motion detection, email alerts.
• Multiple simultaneous viewing by web browser or smartphone.
• Reserved Ethernet ports for wired IP camera connection.

NVR Specification

reserved LAN port for wired IP camera)
Network Protocol| Upnp(play & plug), SMTP(email service), PPPoE(dial-up), DHCP(automatically obtain an IP address), etc.
Power Supply| DC 12V/2A
Power Consumption| <= 5W
Working Environment| Temperature -10°–50°, Humidity 10%–90%
Weight| 1kg

Camera Specification

Software operation

Add Camera
Note: Since IP cameras in NVR kit have been matched code by factory there is no need to add again. If you need to match code, please connect wireless IP camera to any of NVR LAN port and apply power, but make sure there is some channel available for camera.
Steps: Right click mouse to get main menu, go to→System Setup→Channel Setup, click“ quick adding”, then it pops up “video manage” Two ways to add IP camera to NVR “Code Add” and “Auto Add”. Code add: the camera transmits video images to NVR by wifi, IP is 17.20.14.X. Auto add: the camera transmits video images to NVR by network cable, IP is 172.25.123.X.

Video Playback
Step: Right click mouse to get main menu, go to: Video playblack→Channel No.→Record mode →Search time (input beginning time and ending time)→click Search. Recording will come out, drag time bar→click Playback to start.

Playback icon introduction:

• playback previous frame
• playback next frame
• play
• pause
• fast forward x2, x4, x8

Video Backup
Step: Right click mouse to get main menu, go to →Video backup→Channel No.→Record mode→Search time (input start time and end time)→click Search, recording will come out, then choose video→click Video backup Support max 32GB USB-stick, recording will be stored every one hour.

Video Detection
Step 1: Right click mouse to get main menu, go to→System setup→Record setup→ choose Motion→choose All→choose Copy to→click OK to save setting. Step 2: Choose Video detection→set sensitivity as required→choose motion→set Alarm, Bizzar or Email as required→click Copy to→click OK to save setting

Generate Esee ID
To generate Esee ID, the device must be connected with network and IP address should be valid in LAN. Right click mouse to get main menu, go to→System setup→Network setup. If Esee is familiar with LAN, then no need to choose DHCP which could help to get IP address automatically, but input IP address and DNS address by manually . The video recorder will generate ID via network and show the ID in menu.

If Esee is not familiar with LAN, or the video recorder is in independent network, then please choose DHCP to get available IP address. The video recorder will generate Esee ID via network automatically after it gets IP address.

Access in LAN
Step 1: Right click mouse to get main menu, go to System setup→Network setup→ check video recorder IP address. Step 2: Access by computer in LAN, input video recorder IP address and port(no need if the port is 80) in IE browser or other browser, then it will access LAN login webpage, input Esee name and password to log in. Step 3: Video monitoring in LAN will be obtainable when login succeed. Make sure video recorder and computer are in same network segment

Access in WAN
Step 1: Right click mouse to get main menu, go to→System setup→Network setup →check video recorder IP address. Step 2: Access by computer in WAN, input www.e-seenet.com in IE browser or other browser. Then it will access login webpage, input ID, Esee name and password to login. Step 3: Remote video monitoring will be obtainable when login succeed. To ensure smooth remote video, the bandwidth of each channel should be 30KByte/s or above at least.

Android Mobile Phone Application Installation
Step 1: Go to www.e-seenet.com, click Help→Software download→Android mobile application, click download to save in computer→copy it to mobile and install. Step 2: Use mobile phone to scan QR code directly, enter download page and download the application to mobile phone, then install. If mobile phone doesn’t support QR code scan, please input www.e-seenet.com/help/download.php inmobille browser, enter download page to download and install.

iPhone / Android Application Installation

1. Step 1: Go to APP store
2. Step 2: Search Eseenet
3. Step 3: Input Apple ID password
4. Step 4: Click download

Packing List

1. NVR 1 pcs
2. IP camera 4 pcs
3. USB mouse 1 pcs
4. 1m network cable (for IP camera code match) 1 pcs
5. DC 12V/2A power adaptor (for NVR) 1 pcs
6. DC 12V/1A power adaptor (for IP camera) 4 pcs
7. Esee Manual 1 pcs
8. Screw bag (for HDD) 1 pcs
9. Screw bag (for IP camera) 4 pcs

References

• seenet.com/help/download.php
• IP Pro(VR Cam, EseeCloud) - Apps on Google Play
• Download

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>