luminii Plexineon Fixture Catenary Mount Dynamic Color Instruction Manual
- June 3, 2024
- luminii
Table of Contents
luminii Plexineon Fixture Catenary Mount Dynamic Color Instruction Manual
Installation Instructions
Please read all instructions prior to installation and keep for future reference!
-
PRODUCT TO BE INSTALLED BY A QUALIFIED ELECTRICIAN.
-
USE ONLY WITH CLASS 2 POWER UNIT
-
24 VOLTS DC
-
SUITABLE FOR WET LOCATIONS
-
CATENARY MOUNT ONLY
RGB & RGBW WIRING DIAGRAM
RGBW-PXSPI WIRING DIAGRAM
Operation Instruction
SR-DMX-SPI
Smart Pixel LineLED Decoder
There are three buttons on the decoder:
-
Parameter Setting
-
Increase Value
-
Decrease Value
NOTE:
When connected to a controller, DMX512 Signal Decoder will stay in “Decoder
Mode”.
After operation, if no action was taken within 30s, the button lock, and backlight of the screen will turn off.
- Long press M button for 5s to unlock the buttons, and the backlight will turn on.
- Long press M button for 5s to switch between test mode and decode mode after unlocked.
During test mode, the first line of LCD will show: TEST MODE. Use test mode to
verify RGBW Pixel functionality.
Duirng decoder mode, the first line of LCD shows: DECODER MODE. Use decoder
mode when connecting to a Controller and for final installation and
customization.
The second line of the LCD Display shows the current setting and value. Note: 1 Pixel = 1 Cut Increment.
MODE TABLE
| SETTING | LCD DISPLAY | VALUE RANGE | DESCRIPTION |
|---|---|---|---|
| Built-in Programs | TEST MODE MODE NO.: | 1-26 | See Program Table below |
| Program Speed | TEST MODE RUN SPEED: | 0-7 | 0: fast, |
7: slow
DMX Address| DECODER MODE DMX ADDRESS:| 1-512| Address of the starting
point/Pixel of a program
DMX Signal RGB| DECODER MODE DMX RGB SEQ:| RGB, BGR, etc.| N/A
Pixel Quantity| DECODER MODE PIXEL QTY:| 1-170(RGB),
1-128(RGBW)| Number of Pixels to follow a program
IC TYPE| DECODER MODE IC TYPE:| **** 2903, 8903,
2904, 8904
| 2903: N/A,
2904: for RGBW,
8903: N/A,
8904: N/A
Color| DECODER MODE COLOR:| **** MONO, DUAL, RGB, RGBW| MONO:
N/A, DUAL: N/A, RGB: N/A, RGBW: for RGBW
Pixel Merging / Pixel Size| DECODER MODE PIXEL MERGE:| 1-100| Number of Pixels
to merge together
RGB Sequence| DECODER MODE LED RGB SEQ:| RGBW,
BGRW, etc.
| Sequence of RGBW, 24 possible combinations
Integral Control| DECODER MODE ALL CONTROL:| YES, NO| Yes: Merge all Pixels
No: Maintain individual Pixels or Merged Pixels
Reverse Control| DECODER MODE REV-CONTROL:| YES, NO| Reverse program order
Overall Brightness| DECODER MODE BRIGHTNESS:| 1-100| 1: dimmest setting 100:
brightest setting
NOTE:
The actual maximum control pixels of the controller are 1360 (2903) ,1024
(2904). Please set the pixel and pixel combination value according to the
actual situation, and DO NOT exceed the maximum.
PROGRAM TABLE
| PROGRAM NO. | PROGRAM DESCRIPTION |
|---|---|
| 1 | Solid color: Red |
| 2 | Solid color: Green |
| 3 | Solid color: Blue |
| 4 | Solid color: Yellow |
| 5 | Solid color: Purple |
| 6 | Solid color: Cyan |
| 7 | Solid color: White |
| 8 | RGB change |
| 9 | Full color change |
| 10 | RGB fading |
| --- | --- |
| 11 | Full color fading |
| 12 | Red chase with trail |
| 13 | Green chase with trail |
| 14 | Blue chase with trail |
| 15 | White chase with trail |
| 16 | RGB chase with trail |
| 17 | Rainbow chase with trail |
| 18 | RGB chasing and fading |
| 19 | Red chasing green, chasing blue |
| --- | --- |
| **** 20 | Orange chasing purple, chasing cyan |
| 21 | Rainbow chase (7 colors) |
| 22 | Random twinkle: white over red |
| 23 | Random twinkle: white over green |
| 24 | Random twinkle: white over blue |
| 25 | White fading |
| 26 | Off |
NOTE: For Program Table Change: no fading/dimming between color changes
Fade: fade/dim between color changes
Chase: change pixel by pixel
Chase with Trail: change pixel by pixel with fading between
REV0.1 10252022
Support
7777 Merrimac Ave
Niles, IL 60714
T 224.333.6033
F 224.757.7557
info@luminii.com
www.luminii.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>