DynaScan FBP205 Android Control Board with Wireless Module User Manual
- June 3, 2024
- DynaScan
Table of Contents
FBP205 Android Control Board with Wireless Module
User Manual
FBP205 Android Control Board with Wireless Module
User Manual
For Android Control Board With
Wireless module
Product Digital Transmission System
Model No FBP205
Applicable Products Model Description
Model Description
|
Model
---|---
32＂Display| 67401
43＂Display| 67301
49＂Display| 64909
55＂Display| 64428
|
Feature Feature
Feature|
Implementation
---|---
Power Supply| 5.0V±0.25V
Temperature range| Work temperature：-20°C～+70°C Storage
temperature：-55°C～+125°C
Environmental Characteristics
-
Temperature
Operatin- g0°C+40°C
Storage-20°C+70°C -
Humidity
Operating: 10% to 90% (non-condensing)
Storage: 5% to 95% (non-condensing) -
Altitude
Operating- 10,000 ft. (max)
Storage- 20,000 ft. (max)
Hardware Connection
Connector
|
Description
---|---
USB2.0
| 5V| 5V Supply Voltage
DM| USB Data 一
DP| USB Data 十
GND| Ground
Antenna 1| Single-band 5G or dual-band antennas can be used, single-band
2.4G antennas cannot be used
Antenna 2
Module Specification
(1) General Description
This document is to specify the product requirements for 802.11a/b/g/n/ac USB
Module. This Card is based on REALTEK RTL8812CU chipset .It is a complete
dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO MAC/PHY/Radio System-on-a-Chip. This
module provides a high level of integration with a dual-stream IEEE 802.11ac
MAC/ base band/radio. The WLAN operation supports 20MHz,40MHz and 80MHz
channels for data rates up to 866.7Mbps. It is also backward complied with
IEEE 802.11a standard from 5.15~5.825GHz wideband and IEEE 802.11b/g standard
from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and
IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n.
(2) Features
- Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate.
- Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate.
- Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate.
- Compatible wilth IEEE 802.11n standard to provide wireless 300Mbps data rate.
- Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps data rate.
- Support 20MHz, 40MHz bandwidth in 2.4GHz band
- Operation at 2.4G5GHz and 5.155.825GHz frequency band to meet worldwide regulations
- Supports MU-MIMO.
- Support STBC, LDPC
- Supports IEEE 802.11i (WPA and WPA2), WAPI.
- Drivers support Windows, Linux, Android
- High speed USB 2.0 interface RoHS compliant
Application Diagrams
(1) Functional Block Diagram
(2) General Requirements
IEEE 802.11a Section
Feature
|
Detailed Description
---|---
Radio and Modulation Type| QPSK、BPSK、16QAM、64QAM with OFDM
Operating Frequency
| 5.15G～5.25GHz
5.725G～5.825GHz
Data Rate| at most 54Mbps
Media Access Protocol| CSMA／CA with ACK
Transmitter Output Power at Antenna Connector| Typical RF Output Power
(tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
15±2 dBm at 54Mbps
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at each RF
chain. Frame (1000-byte PDUs) Error Rate＜10% at room Temp. 25 degree C
-73 dBm at 54Mbps
IEEE 802.11b Section
Feature
|
Detailed Description
---|---
Radio and Modulation Schemes| DQPSK、DBPSK、DSSS、CCK
Operating Frequency| 2400M～2483.5MHz, ISM band
Channel Numbers| 13 channels for Worldwide
Data Rate| at most 11Mbps
Media Access Protocol| CSMA／CA with ACK
Transmitter Output Power at Antenna Connector
| Typical RF Output Power (tolerance±2dB) at each RF chain, Data Rate and at
room Temp. 25 degree C
16±2 dBm at 11Mbps
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at Which Frame
(1000-byte PDUs) Error Rate＝8% at room Temp. 25 degree C
-82 dBm at 11Mbps
IEEE 802.11g Section
Feature
|
Detailed Description
---|---
Radio and Modulation Type| QPSK、BPSK、16QAM、64QAM with OFDM
Operating Frequency| 2400M～2483.5MHz, ISM band
Channel Numbers| 13 channels for Worldwide
Data Rate| at most 54Mbps
Media Access Protocol| CSMA／CA with ACK
Transmitter Output Power at Antenna Connector| Typical RF Output Power
(tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
15±2 dBm at 54Mbps
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at Which Frame
(1000-byte PDUs) Error Rate＜10% at room Temp. 25 degree C
-73 dBm at 54Mbps
IEEE 802.11n Section
Feature
|
Detailed Description
---|---
Radio and Modulation Type| QPSK、BPSK、16QAM、64QAM with OFDM
Operating Frequency| 2.4GHz| 2400M～2483.5MHz
5GHz| 5.15G～5.25GHz
5.725G～5.825GHz
Data Rate| at most 300Mbps
Media Access Protocol| CSMA／CA with ACK
Transmitter Output Power at Antenna Connector
| Typical RF Output Power (tolerance±2dB) at each RF chain, Data Rate and at
room Temp. 25 degree C
2.4GHz Band／HT20／HT40| 15±2 dBm at MCS7
5GHz Band／HT20／HT40
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at each RF
chain. Frame (1000-byte PDUs) Error Rate＝10% at room Temp. 25 degree C
| 2.4GHz Band／HT20| -70 dBm at MCS7
---|---|---
2.4GHz Band／HT40| -66 dBm at MCS7
5GHz Band／HT20| -71 dBm at MCS7
5GHz Band／HT40| -67 dBm at MCS7
IEEE 802.11ac Section
Feature
|
Detailed Description
---|---
Radio and Modulation Schemes| QPSK、BPSK、16QAM、64QAM、256QAM、OFDM
Operating Frequency| 5.15～5.25GHz；5.725～5.825GHz
Data Rate| at most 866.7Mbps
Media Access Protocol| CSMA／CA with ACK
Transmitter Output Power at Antenna Connector| Typical RF Output Power
(tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
HT20：15±2 dBm at MCS8
HT40：15±2 dBm at MCS9 HT80：13±2 dBm at MCS9
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at each RF
chain. Frame (1000-byte PDUs)
Error Rate＜10% at room Temp. 25 degree C
5GHz Band／HT20：-64 dBm at MCS8
5GHz Band／HT40：-61 dBm at MCS9 5GHz Band／HT80：-58 dBm at MCS9
FCC Statement
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CAUTION
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
RF exposure warning
This equipment must be installed and operated in accordance with provided
instructions and the antenna(s) used for this transmitter must be installed to
provide a separation distance of at least 20 cm from all persons and must not
be co-located or operating in conjunction with any other antenna or
transmitter. End-users and installers must be provide with antenna
installation instructions and transmitter operating conditions for satisfying
RF exposure compliance.
End Product Labeling
The end product shall bear the following 15.19 statement: This device complies
with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation. This transmitter module is authorized only for use
in device where the antenna may be installed such that 20cm may be maintained
between the antenna and users. The final end product must be labeled in a
visible area with the following: Contains FCC ID: 2AKWYFBP205
This module is intended under the following conditions
- This module is certified pursuant to Part 15 rules section (15.247).
- This module is limited to host model number: 67301, 67401, 64909, 64428/ Brand: DynaScan
- This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.
Frequency Band
| Antenna Type|
Gain(dBi)
---|---|---
2400-2500MHz| PIFA| -3.04
5150-5850MHz| PIFA| -2.31
Information on test modes and additional testing requirements
This module is restricted to integration into hosts for indoor use only.
Be limited the operation channels in channel 1-11 for 2.4GHz band.
The separate approval is required for all other operating configurations,
including portable configurations with respect to Part 2.1093 and different
antenna configurations. The information on how to configure test modes for
host product evaluation for different operational conditions for a stand-alone
modular transmitter in a host, versus with multiple, simultaneously
transmitting modules or other transmitters in a host can be found at KDB
Publication 996369 D04.
According to KDB 388624 requirements we will retain control over the final
installation of the modular such that compliance of the end product is
assured.
Clear and specific instructions describing the conditions, limitations and
procedures for third parties to use and/or integrate the module into a host
device (see Comprehensive integration instructions below). Resolve: Supply
example as follows:
Installation Notes:
- When connect module to the host device, the host device must be power off.
- Make sure the module pins correctly installed.
- Make sure that the module does not allow users to replace or demolition.
- Host approval is limited in mobile condition.
- Labeling are pre-checked by modular vendor before marking.
- Output power, and spurious emission are checked as always prior to permission to sign before marking.
Additional testing, Part 15 Subpart B disclaimer
Appropriate measurements (e.g. 15B compliance) and if applicable additional
equipment authorizations (e.g. SDoC) of the host product to be addressed by
the integrator/manufacturer.
This module is only FCC authorized for the specific rule part 15.247 listed on
the grant, and the host product manufacturer is responsible for compliance to
any other FCC rules that apply to the host product as being Part 15 Subpart B
compliant.
The user manual of the end product should include
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. The
antenna(s) used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter. For product available in
the USA/Canada market, only channel 1~11 can be operated. Selection of other
channels is not possible.
Name: DynaScan Technology, Inc.
Address: 7 Chrysler, Irvine, CA 92618,
USA Office: +1 949.421.0348
https://www.dynascandisplay.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>