DynaScan FBP206 Android Control Board with Wireless Module User Manual

User Manual
for Android Control Board With
Wireless module  FBP206 User Manual
Product: Digital Transmission System
Model No: FBP206

Applicable Products

Feature

temperature：-55°C～+125°C

 Environmental Characteristics

1. Temperature
   Operating：0°C～+40°C
   Storage：-20°C～+70°C

2.  Humidity
   Operating：10% to 90% (non-condensing)
   Storage：5% to 95% (non-condensing)

3.  Altitude
   Operating：10,000 ft. (max)
   Storage：20,000 ft. (max)

USB2.0

| 5V| 5V Supply Voltage
DM| USB Data 一
DP| USB Data 十
GND| Ground
Antenna 1| Single-band 5G or dual-band antennas can be used, single-band 2.4G antennas cannot be used
Antenna 2

Module Specification

1. General Description
   This document is to specify the product requirements for 802.11a/b/g/n/ac USB Module. This Card is based on the REALTEK RTL8812CU chipset . It is a complete dual-band(2.4GHz and 5GHz)WIFI 2×2 MIMO MAC/PHY/Radio System-on-a-Chip. This module provides a high level of integration with a dual-stream IEEE 802.11ac MAC/ baseband/radio. The WLAN operation supports 20MHz,40MHz and 80MHz channels for data rates up to 866.7Mbps. It is also backward complied with IEEE 802.11a standard from 5.15~5.825GHz wideband and IEEE 802.11b/g standard from 2.4~2.5GHz. It can be used to provide up to 54Mbps for IEEE 802.11a and IEEE 802.11g, 11Mbps for IEEE 802.11b and 300Mbps for IEEE 802.11n.

2. Features
   Compatible with IEEE 802.11a standard to provide wireless 54Mbps data rate.
   Compatible with IEEE 802.11b standard to provide wireless 11Mbps data rate.
   Compatible with IEEE 802.11g standard to provide wireless 54Mbps data rate.
   Compatible with IEEE 802.11n standard to provide wireless 300Mbps data rate.
   Compatible with IEEE 802.11ac standard to provide wireless 866.7Mbps data rate.
   Support 20MHz, 40MHz bandwidth in 2.4GHz band Operation at 2.4G～5GHz and 5.15～5.825GHz frequency bands to meet worldwide regulations
   Supports MU-MIMO.
   Support STBC, LDPC
   Supports IEEE 802.11i (WPA and WPA2), WAPI.
   Drivers support Windows, Linux, Android
   High-speed USB 2.0 interface
   RoHS compliant

Application Diagrams

1. Functional Block Diag
2. General Requirements****

IEEE 802.11a Section

5.725G～5.825GHz
**Data Rate| ****at most 54Mbps
****Media Access Protocol| ****CSMA／CA with ACK**

Transmitter Output Power at Antenna Connector

| Typical RF Output Power (tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
15±2 dBm at 54Mbps

Receiver Sensitivity at Antenna Connector

| Typical Sensitivity at each RF chain. Frame (1000-byte PDUs) Error Rate＜10% at room Temp. 25 degree C
-73 dBm at 54Mbps

IEEE 802.11b Section

Power (tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
16±2 dBm at 11Mbps
****Receiver Sensitivity at Antenna Connector| Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate＝8% at room Temp. 25 degree C
-82 dBm at 11Mbps**

IEEE 802.11b Section

(tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
****15±2 dBm at 54Mbps
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at Which Frame (1000-byte PDUs) Error Rate＜10% at room Temp. 25 degree C
-73 dBm at 54Mbps**

IEEE 802.11g Section

Operating Frequency

| 2.4GHz| 2400M～2483.5MHz

5GHz

| 5.15G～5.25GHz
5.725G～5.825GHz
Data Rate| at most 300Mbps
Media Access Protocol| CSMA／CA with ACK

Transmitter Output Power at Antenna Connector

| Typical RF Output Power (tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C

2.4GHz Band／HT20／HT40

| ****

15±2 dBm at MCS7

5GHz Band／HT20／HT40

Receiver Sensitivity at Antenna Connector| Typical Sensitivity at each RF chain. The frame (1000-byte PDUs) Error Rate＝10% at room Temp. 25 degree C
| 2.4GHz Band／HT20| -70 dBm at MCS7
---|---|---
2.4GHz Band／HT40| -66 dBm at MCS7
5GHz Band／HT20| -71 dBm at MCS7
5GHz Band／HT40| -67 dBm at MCS7

IEEE 802.11ac Section

(tolerance±2dB) at each RF chain, Data Rate and at room Temp. 25 degree C
HT20：15±2 dBm at MCS8 HT40：15±2 dBm at MCS9 HT80：13±2 dBm at MCS9
Receiver Sensitivity at Antenna Connector| Typical Sensitivity at each RF chain. Frame (1000-byte PDUs) Error Rate＜10% at room Temp. 25 degree C
5GHz Band／HT20：-64 dBm at MCS8 5GHz Band／HT40：-61 dBm at MCS9 5GHz Band／HT80：-58 dBm at MCS9**

FCC Statement： FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
CAUTION ： Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF exposure warning: This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance.
End Product Labeling： The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This transmitter module is authorized only for use in device where the antenna may be installed such that 20cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: ＂Contains FCC ID: 2AKWYFBP206＂

This module is intended under the following conditions：

1. This module is certified pursuant to Part 15 rules section(15.247).
2. This module is limited to host model number: 65512/ Brand: DynaScan
3. This module has been approved to operate with the antenna types listed below, with the maximum permissible gain indicated.

Information on test modes and additional testing requirements：
This module is restricted to integration into hosts for indoor use only. Be limited to the operation channels in channels 1-11 for the 2.4GHz band. Separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations. The information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus multiple, simultaneously transmitting modules or other transmitters in a host can be found at KDB Publication 996369 D04.
Additional testing, Part 15 Subpart B disclaimer： Appropriate measurements (e.g. 15B compliance) and if applicable additional equipment authorizations (e.g. SDoC) of the host product to be addressed by the integrator/manufacturer. This module is only FCC authorized for the specific rule part 15.247 listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host product as being Part 15 Subpart B compliant.
The user manual of the end product should include： This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.

Name DynaScan Technology, Inc.
Address: 7 Chrysler, Irvine, CA 92618, USA
Office: +1 949.421.0348
https://www.dynascandisplay.com

Documents / Resources

| DynaScan FBP206 Android Control Board with Wireless Module [pdf] User Manual
FBP206, 2AKWYFBP206, Android Control Board with Wireless Module, FBP206 Android Control Board with Wireless Module, Android Control Board
---|---

References

• Home - DynaScan

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>