REDLINE TS1200W AC1200 High Power Dual Band Wall Plug WiFi Extender Installation Guide
- June 3, 2024
- REDLINE
Table of Contents
TS1200W
Quick Installation Guide
AC1200 High Power Dual Band
Wall Plug WiFi extender
Ver 5.01.14001
Product introduction
Product indicator and Interface button
Product Applications
Wireless Expander is widely used in large space to improve wifi coverage, effective expansion of WiFi signal, easy to use.
Quick Configuration
WPS quick setting
First click the router’s WPS, and then click the WPS button of the wireless
extender within 1 minute to complete the expansion in one click.
Tips: Please pay attention to the indicator changes during the expansion
process. The blue or yellow steady light indicates that the expansion is
successful. If the expansion is not successful, please check whether the WPS
function of your router is enabled (for how to enable the WPS function of the
router, please refer to the manual of your router).
WEB quick settings
If you do not WPS connection or WPS connection can not be successful, can use
cellphone connected to the device default wifi, enter the device management
interface to connect.
Open the cellphone WiFi settings interface, search and connect to a wireless
network: The WiFi name is shown in the SSID of the product label.
When the mobile phone is connected to WiFi, it will automatically jump to the
wizard page. Follow the instructions on the page to complete the setup. If
there is no automatic redirection, please use your browser, enter 192.168.1.1
to open the default management page.
After entering the management page, click the “Start Experience” button on the
interface and follow the instructions on the page to complete the settings.
Note: For example, if you want to extend the WiFi in your home, enter the
WiFi password in your home. Do not enter the wrong password.
This product can extend 2.4G or 5G signals separately, or both signals. You
can click the switch button as needed. Please keep in mind the administrator
password set on the
settings page, for logging in to the management interface in the future.
If there are no signals you want to expand in the expanded signal display
list, please click More to expand the list, and then click to collapse.
Device indicator
Status of indicator lights as follows:
| Blue light flashes | During expansion |
|---|---|
| Blue light stays on | Successful expansion, moderate distance from router |
| Steady yellow light | Successful expansion, too far away from the router. |
| Light off | Not extended or failed to expand |
Tips: After completed set up,in order to obtain good amplification effect,please put the wifi extender in appropriate distance from the router and the internet equipment.(After insert and pull out extender don’t need to reconfigure ). It is recommended to extend the extender antenna perpendicular to the horizontal for good coverage.
SSS / FAQ
Q:Can not connect network after the installation successful?****
– A:Please check the password is correct, if not, please enter the correct password.
Q:Why network speed is very slow after expanding the signal?****
– A:Please ensure that the wifi signal before the relay network speed is normal,check the distance between the device and the router is appropriate,please adjust the placement of this product.
Q:How to restore the range extender to its factory default settings?****
– A:ln the case of wifi extender connection power supply,use tip shaped object(Such as paper clips, a toothpick) inserted into the reset hole for 5 seconds,wait for the light to turn on when it is normally on.
Q:What should I do if you can not open the settings interface?****
– A:Please try the following measures:!. Ensure that the device is powered on, the indicator is normal display; 2. the device is connected to the produces wireless network.3. mobile phone or computer network – IP address is set to automatically obtain; 4. replace the other browser to try again.
Q:Network cable connection device can not access the Internet?****
– A:Make sure that the expander has relayed the signal normally and that the device at the network cable end has set the IP address automatically.
Q:Why do I find that I can not find the page during setup?****
– A:Some mobile phones may intelligently detect whether the connected WiFi can access the Internet or not. During the setting ，the WiFi may be disconnected. You only need to check the wifi you are connected to. If the connected WiFi is not transmitted by the device, you just need to reconnect and refresh the page Can be.
Use Skills
As shown in the figure above, point B is the router launching point, and point
A is your location on the Internet. If the signal is weak, we can place our
WIFI repeater in the middle of the direct distance between points A and B,
which can enlarge the coverage of WIFI, and alleviate the problem that weak
signal of point A can not cover dead angle.
The following figure is an error demonstration: too close or too far from the
launch point, the relay effect is not ideal, please pay attention to the
correct use.
Precautions:
- In the thunderstorm it is recommended to unplug it,to prevent lightning damage.
- Away from the power, keep the ventilation.
- Do not subject the product to strong shock or vibration to prevent damage to the product.
- Do not disassemble or modify this product without permission.
- In storage, transportation and operating environment, please pay attention to water.
- Microwave ovens, Bluetooth devices, refrigerators, etc. can seriously interfere with the wireless signal, please try to place in a spacious and accessible area, and away from the above equipment.
- Access to the normal voltage and current of the home circuit.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>