REDLINE TS720W Wall-Plug WiFi Extender Installation Guide

TS720W
Quick Installation Guide
Wall-plug WiFi extender
Ver 4.08.05001

 Product introduction

Product indicator and Interface button

Product Applications

Wireless Expander is widely used in large space to improve wifi coverage, effective expansion of WiFi signal, easy to use.

Product setting

WPS quick setting

Make sure that you want to repeater expansion is your router signal and the router with WPS function,If you do not have this function you can skip this step.

1. Connect this product near your router and power on to make it work properly.
2. Press the router WPS button to enable the WPS function of the router(Please refer to your router manual WPS connection specific operation).
3. Then press the WPS button on the side of the product.the light on the device will turn off and then on again,this product is restarted,then the WPS pairing success after  the corresponding indicator light,WPS connection is successful. Press the router WPS button to enable the WPS function of the router 2 Press the WPS button on the side of the device,make a quick connection.
4. WPS after the success of this product can be moved to a distance （Area covered by the router signal ）,then expand the signal coverage.Repeater signal is the wifi  name of your router plus suffix -plus,the extended WiFi password is your router’s password.

Tips:
1.If the device is on the wrong wifi router when the WPS button is pressed,Please reset and match it. 2.If the WPS match failed, set through the following operation.

Cellphone setting

If you do not WPS connection or WPS connection can not be successful,can use cellphone connected to the device default wifi,enter the device management interface to  connect.

1. Open the cellphone WiFi settings interface,search and connect to a wireless network: The WIFI name is shown in the SSID of the product label.
2. Connected to the default wifi, pop-up login to the wireless network, click to enter or open the cellphone browser, Enter the URL: 192.168.18.1, into the management  interface, Click on the interface “Start Settings” button, the amplifier will start to automatically scan the surrounding wireless network.
3. In the search of the wireless network, select the need to expand the wireless network name.Set wireless signal amplification
4. Enter the wireless password (the password is to expand the wifi password,for example, you want to extend this xxxxxx wifi,you need to know this password),Click “NEXT”.
5. Wait a moment, complete the setup, prompt the extended wireless name and wireless password in this interface,open the phone wifi settings interface, scan and connect  your extended wifi name plus suffix “-Plus” signal,you can use the network normally. Status of indicator lights as follows:

Signal light keeps on| Extended successful,in appropriate distance from the router/main AP
---|---
Signal light put out| Extended failure
Signal light flashing| Extended successful,too far from the router/main AP

Tips: After completed set up,in order to obtain good amplification effect,please put the wifi extender in appropriate distance from the router and the internet equipment.(After insert and pull out extender don’t need to reconfigure ).It is recommended to extend the extender antenna perpendicular to the horizontal for good coverage.

SSS / FAQ

Q:Can not connect network after the installation successful?****

– A:Please check the password is correct, if not, please enter the correct password.

Q:Why network speed is very slow after expanding the signal?****

– A:Please ensure that the wifi signal before the relay network speed is normal,check the distance between the device and the router is appropriate,please adjust the placement of this product,

Q:How to restore the range extender to its factory default settings?****

– A:In the case of wifi extender connection power supply,use tip shaped object(Such as paper clips, a toothpick) inserted into the reset hole for 5 seconds,until the lights go out after loosening,wait for the light to turn on when it is normally on.

Q:What should I do if you can not open the settings interface?****

– A:Please try the following measures:1. Ensure that the device is powered on, the indicator is normal display; 2. the device is connected to the product’s wireless network.3. mobile phone or computer network IP address is set to automatically obtain; 4. replace the other browser to try again.

Q:Network cable connection device can not access the Internet?****

– A:Make sure that the expander has relayed the signal normally and that the device at the network cable end has set the IP address automatically.

Q:Why do I find that I can not find the page during setup?****

– A:Some mobile phones may intelligently detect whether the connected WiFi can access the Internet or not. During the setting, the WiFi may be disconnected. You only need to check the wifi  you are connected to. If the connected WiFi is not transmitted by the device, you just need to reconnect and refresh the page Can be.

Use Skills

****As shown in the figure above, point B is the router launching point, and point A is your location on the Internet. If the signal is weak, we can place our WIFI repeater in the middle of the direct distance between points A and B, which can enlarge the coverage of WIFI, and alleviate the problem that weak signal of point A can not cover dead angle.
The following figure is an error demonstration: too close or too far from the launch point, the relay effect is not ideal, please pay attention to the correct use.

Precautions:

1. In the thunderstorm it is recommended to unplug it,to prevent lightning damage.
2. Away from the power, keep the ventilation.
3. Do not subject the product to strong shock or vibration to prevent damage to the product.
4. Do not disassemble or modify this product without permission.
5. In storage, transportation and operating environment, please pay attention to water.
6. Microwave ovens, Bluetooth devices, refrigerators, etc. can seriously interfere with the wireless signal, please try to place in a spacious and accessible area, and away from the above equipment.
7. Access to the normal voltage and current of the home circuit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>