G-Ocean GHTF1502 Fan Heater Instruction Manual
- June 6, 2024
- G-Ocean
Table of Contents
G-Ocean GHTF1502 Fan Heater
Our customer service team is available to assist you with product and service questions. We’d love hear your voice about our product and service, please do not hesitate to contact us, we would like to offer you the satisfied customer service in 2 days.
FACEBOOK: G Ocean
MESSENGER: G Ocean
E-MAIL: gocean_service@outlook.com
IMPORTANT INSTRUCTIONS
This appliance can be used by all kinds of people, including children aged 8 years above and persons with reduced physical, sensory or mental capabilities, but making sure those people were know how to use the machine safely and understand the hazard involved, or using under supervision.Children shall not play with the appliance. Cleaning and maintenance shall not be made by children age 8 above without supervision. If the supply cord is damaged, avoiding danger, it must be replaced by the manufacturer, its service agent or similarly qualified persons.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:
- Read all instructions before using t his heater.
- This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving t his heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least a 1 feet (1 m) from the front of the heater and keep them away from the sides and rear.
- Extreme caution is necessary when any heater is used by or near children or invalids and whenever the heater is left operating and unattended.
- Always unplug heater when not in use.
- Do not operate any heater with a damaged cord or plug or after the heater malfunctions, has been dropped or damaged in any manner. Discard heater, or return to authorized service facility for examination and/ or repa ir.
- Do not use outdoors.
- This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. Never locate heater where it may fall into a bathtub or other water container.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- To disconnect heater, turn controls to off, then remove plug from outlet.
- Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.
- To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces , like a bed, where openings may become blocked.
- A heater has hot and arcing or sparking parts inside. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
- Use t his heater only as described in t his manual. Any other use not recommended by the manufacturer may cause fire, elect ric shock, or injury to persons.
- Always plug heaters directly into a wall out let/receptacle. Never use with an extension cord or relocatable power tap (outlet/power st rip).
“SAVE THESE INSTRUCTIONS”
Overheating protection: there is a thermal fuse installed in the heater motor,
when the motor is overheated due to a variety of acc idents, and the motor
temperature reaches the level to activate the thermal fuse, the fuse will be
blown out to cut off the power. * Tip-over switch: As a safety measure, the
unit wi ll shut off automatically if it is knocked over. Should this occur,
simply turn the heater off and stand it back upto a regular upright position,
then switch it back on.
Product features
First of all, welcome to use our products. The series of luxurious tower heaters manufactured by us are featured with beautiful appearance, novel sructure, lightweight and convenience, softness and comfort, fast heati ng speed, low power consumption, easy maintenance characteristics, suitable to be used in houses, hotels and other places, which is an ideal home appliance for you to remove winter cool and enjoy the warm air.
Parts list (schematic)
How to assemble
- Leave the two parts of the base from the box, making the holes of the two-part base are aligned and the two parts are formed into a complete base. (As shown in Fig. 1)
- Run the power cord through the base, aligning the base with the holes on the tower heater body, then secure the power cord under the base clip to tighten the base with the heater body. (As shown in Fig. 2)
After the base is put on the heater body, follow the schematic to secure the power cord under the base clip, then tighten the screws. - When the base is disassembled, screwing out the screws first, then take the base out. (The method to disassemble the base is as shown in Fig. 3)
Hold the clip and forcibly pull the base out, after the clip comes out , use the same method to remove another clip.
Performance specification and parameters
How to use
Using Method of Remote Control
Operated by using a remote control (each button on the remote control is the
same as the heater):
-
ON/OFF:
When this button is press, the tower heater will start at a low speed; pressing again, it will stop working. (Note: when the heater function is on, and press off, it will be 30 seconds delay switch off.) -
HEATER
When this button is press, press one is “low speed “, press two is “high speed”, And press again the heater function will stop working. -
SET TEMP
This button could help you set the temperature mode, which from 60°F as lowest, to increase 5°F by per press, the range from 60°F form 90°F max.
( Note 1: when the environment temperature is higher than the set temperature, the heater function will stop. When the set temperature is higher than the environment temperature, then the heater function will start to work.)
( Note 2: Long pressing the SET TEMP on the heater can increase the temperature quickly. But the remote control does not support this function) -
SWING
When this button is press, the heater starts to swaying the wind, pressing again, the heater stops swaying. -
TIMER
When the heater is under working, this button wi 11 help you enter timing status and the setting time is 1 hour. The timing can be selected from 1h to 12h.
When the timer is set to 12h, pressing this button, the timing selection will be canceled.
Press and hold this button for three seconds, turn on child safety lock.
Press and hold this button for three seconds again, turn off child safety lock . (Control panel)
-
LOCK
Press this button , turn on child safety lock. Press this button again, turn off child safety lock.
The above operation can also be operating on the control panel of the heater,
with the method same as the one described above.
Note: GHTF1502 model with auto -extinguish screen function, under the
heater working on, the control panel will be auto – extinguish screen if
without any operation for 3 minutes.
Proper usage of the remote control and battery replacement
- When the remote control is used, make sure that the head of the front of the remote control is aligned with the receiving window on the heater body.
- The remote control can be about 5m from the front of the heater body; it can be normally operated if the deviation is within 30 degrees.
- Avoid direct sunlight on the receiving window, so as not to affect t he effect of the receiver.
- If the remote control is not used for a long time, remove the battery and handle it properly.
- When using the remote control, inst all the battery. The remote control operates on one lithium battery, with the insertion method as shown below:
a. Open the battery cover.
b. Insert a new battery, pay attention to the polarity of t he battery(+ and-).
c. Close the battery cover.
Circuit diagram
(The technology is under continuous improvement , so no further notice will be given if there are any changes.)
How to maintain
- Before cleaning this product, make su re that the power is turned off first.
- Do not use water or other liquid to clean the electrical components (such as swit ching power supply, motor, etc.) and the electrical components can be wiped clean with a clean cloth.
- Do not use any grinding tools and solvents that can damage the surface to clean the product. You can wash the product with detergent and wipe it dry with a clean cloth.
- Do not take the product apart for modification. It is recommended to inspect and clean the product annually to extend its service life.
Warranty instructions
- From the date of purchase, in the period for the guarantee of repair (one year), for any non-human damage, the user can present the proof of purchase, certificate of conformity and warranty card to enjoy free after-sale service .
- This warranty does not cover damage resu lt ing from any of the following: negligent use or misuse of the product, unauthorized disassembly or use contrary to the operating instructions.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>