HONITURE Q6 Pro Robot Vacuum Cleaner with Mop Self Emptying Instruction Manual

Instruction Manual

Tips
This product is only available at HONITURE retail store. and this warranty applies to customers who purchase this product directly from store managed by us. It does not apply to third parties when the customer resells the product or turns it over to third parties.

Part-1 Safety Instructions

Use Restrictinos

• Plastic bags are dangerous. Please keep them away from infants and children as they may pose a choking hazard.

• This productis only intended to be used to clean floors in residential households. Do not use this product outdoors (such as open balconies), on surfaces other than floors (such as sofas) orin commerdial industrial environments.

• Donot usethis product on a suspended platform, such as a balcony, which does not have any guardrails.

• Do not operate this product f the environment above 40 degrees Celsius, below 0 degrees Celsius orwhen any liquid or sticky material is present on the ground Before using, please remove any wires on the ground to avoid dragging the wires when the robot is running.

• Please put away the fragile items and sundries (such as vases, plastic bags,etc.) to avoid the damage ofvaluables due to the obstruction or collision of the device during operation.

• Do not allow persons (including children) who lack physical, intellectual or experience or common sense to use this product without supervision or guidance from someone capable of properly operating this product.

• Do notallow children to use this device as atoy.

• Do not place the main brush cleaner in an area accessible to children.

• Do not let human or pet har,fingers near the suction port when the main machine isin operation.

• Do not usethis product to clean any burning objects (such as unextinguished cigarette butts).

• Do notallow the device to absorb hard or sharp objects (such as decoration waste, glass, nails, etc)

• Do not usethe laser sensor protection cover, the main engine cover and the collision buffer as handles to carry the machine.

• To clean and maintain the machine and dust collection charging dock, the operator must turnit offfirstly and pul the plug from the socket and disconnect the power.

• Do not soak the main machine and dust collection dock in water or clean with water.

• Do not use awetcloth or any liquid towipe any part of the product.

• Do not mop on a carpet environment.

• Please use the product in accordance with the instructions of the manual. Any damage or injury caused by improper use shall be borne by the user.
  Battery and Charging

• It is forbidden to burn products even when they are severely damaged, as the batteries may explode.

• Do not use any third party batteries, chargers and charging piles.

• Do ot disassemble, repair or modify the battery or charging pile without authorization.

• Do ot place the charging pile near the heat source (such as radiator).

• Do not wipe o clean the shrapnel of the charging pile with wet cloth or hands.

• Do not throw awaythe discarded battery atwill. It should be disposed of by a professional recycling institution.

• If the power cord is damaged, it must be replaced by a professional from the manufacturer,its maintenance department or similar department in order to avoid danger.

• If you need totransport the product, please ensure that the mainframe s switched off and itis recommended to use the original packaging box.

• Do not pour water into the device orimmerse the device inwater.

• If notused foralongtime, please tum off themainframe after full chargeand putitina cool and dry place, and charge itatleast once every 3monthstoavoid damage to the battery dueto overdischarge.

• To remove the battery, use the righttools Fist remove the bottom cover screw, then open the bottom cover of the product, unplug the battery connecting terminal and remove the battery from the battery box.

• The battery mustbe removed from the appliance beforeitis discarded.

• When the batteryis removed, the appliance must be powered off.

• If the symbol for detachable supply unitis used, its meaning shall be explained. – symbol IEC 60417-6181

• For the purposes of rechargingthe battery, onlyse the detachable supply unit provided with this appliance.

Class 1 laser producdts, the product radar in accordance with the GB7247.1-2012/IEC 60825-1.2014 Class 1 laser safety standards, will not produce dangerous laser radiation to the human body.
Correct Disposal of this product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the retum and collection systems or contact the retailer where the product was purchased. They can take this product for environmentally safe recycling
FCC STATEMENT :
This device complies with Part 15 of the FCC Rules. Operationis subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning; Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipmenthas been tested and found to comply with thelimits fora Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interferencein a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occurin a particular installation. If this equipment does cause harmul interference to radio or television reception, which can be determined by tuming the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/ TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
IC Statement:
This device contains licence-exempt transmitter(s);receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference,
2. This device must accept any interference, including interference that may cause undesired operation of the device

This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body

Part-2 Packing list

Note: the product, accessories, user interface and other lustrations in the manual are schematic diagrams for reference only. Accessories installed on the sweep and towing robot These fittings are installed on the dust collecting charging pile Tip: dust bag is consumable, it can not be recycled, please replace regularly.

Part-3 Basic Parameters

Basic parameters

Dust collection Charging Pile
Output of dust collection charging pile| 24v ****12A
Rated power of dust collection charging pile| 950w
Product dimensions| 250210 x 350 mm
Complete Machine
Net weight| About 7.8 kg

Part-4 Product Introduction

1. Robot introductionIndicator reminder
   Breath: Gradually on and off in 4 seconds.
   Slowly flash: On for 0.7 seconds, off for 0.8 seconds.
   *Faster flash: On for 0.1 seconds, off for 0.2 seconds.The machine status| Powerindicator (networked/disconnected)| Recharge indicator light status
   ---|---|---
   Standby| Long bright blue light| Putout
   Charging| Blue light breath| Putout
   Suspended| Blue lightis slow| Putout
   Cleaning| Long bright blue light| Putout
   Recharge| Put out| Orange light long on
   Abnormal| Red light fast flash| Light OfFf
   Turned off| Blue light fast flash| Light Off
   Wi-Fi not connected| Blue light slow flash| Light OfFf
   Wi-Fi not connected| Blue light long bright| Light Off
   Wi-Fi being connected| Blue light long bright| Light OfFf
2. Dust Collection Charging Pile Indicator reminder
   Tip:
   The st bgisconumbie Orebgisnled anthe ot and addiionaltwo bags are provided in package. After use-0p ou need to make a putchase though the designated offcial channel.
   Product abnormalities and damages caused by the use of consumables from unofficial channel are not covered within the warranty.

Part-5 Installation of dust collection Charging Station

Install the Dust Collection Charging Pile   Warning:
To prevent the risk of your robot falling downstais, ensure that the charging station is placed at least 4 feet (1.2 metres) away from stairs
Notice:

1. Put in a place with good wifi signal
2. Less obstacles, the wider the better
3. Do not bundle the cords and stretch them along the wall

Please stay away from the stairs to prevent the robot from accidentally falling down due to insufficient map information at the beginning of startup.Please place it in an environment with good Wi-Fi signal

Part – 6 How to use

USE
Remove the Limit Bar
Put the sweeping and mopping robot on the flat indoor ground, and remove the protection device of imit bar at both ends of the front bumper.
Remove the protective film
Please remove the protective film from the surface before use. Charing of the Sweeping and Mopping Robot
Press and hold the button for 3 seconds to start the sweeping and mopping robot, and then short-press the button  to make the fobot recharge automatically. The robot enters the ready state once fully charged. Switching to mopping mode

1. Open the lid of the tank and fill it with water from the inlet shown in the picture.
2. Put2-IN-1dust and water container back into the sweeper.
3. Attach the mop to the mop bracket and fasten the velcro tightly.
4. Press the buttons on both sides of the mop bracket and then install the mop assembly below the dust box.

Please fill water from the inlet as seen on the drawing,
Because the outlet is small, water seepage needs a certain timeou can also wet the mop and put it on the sweeper.
Do not add detergent to the water used in the mop in order to avoid corrosion of the water tank caused by certain chemical detergents.
How to connect to the APP

1. Scan the QR code, download and install the APP.
   Users who have already installed the APP will directly enter the device connection page,

2. Users can download and install the HonySmart APP by searching for it on Google Play or Apple Store.

3. Open the homepage of the APP, click “+ in the upper right comer of the page, and add devices according to the prompts of the APP.

http://www.honiture.com/honitureapp.html

Note: Due to APP upgrades and updates, the actual operation may be slightly different from the above description
Please follow the current instructions in the APP.
Reset Wi Fi
Atthe same time, long press the key and the key for 3 seconds, and a voice message wil be heard indicating that the Wi-Fi has been reset. Power indicator is slowly flashing blue , and the robot will enter the state of waiting for connection
Note: Only support Wi-Fi 2.4 GHz Network Incompatible for 5G and the robot will enter the state of waiting for connection.
Apple: 105 10.0 and above
Android: Android 8.0 and above
Note:

1. Please put the robot and charging base in a place with good WIFI signal.
2. Make sure that the power is turned on.
3. Ensure the mobile phone connected has turned on the Bluetooth.

Description of buttons and basic functions

The power indicator blinks in white after blinking in blue slowly for 5 seconds| The sweeping and mopping robot enters thestandby state
Turn on| | Short press the button to turn on the machine| | Start the whole- house cleaning
When the robot is still| | Press the button for 3 seconds| The power indicator will blink in blue quickly for 5 seconds and then go out| The machine will turn off
In the process of cleaning| | Short press the button| | The sweeping and mopping robot will pause
In the process of cleaning| –| Automatically| | •If the sweeping and mopping robot is still and has not operated for more than 60 minutes, it will enter the hibernate state.
•In the hibernate state,you can give any button a brief press to wake up the machine.
In the process of cleaning| | Short press the button| | The sweeping and mopping robot will return to the dust collection charging pile to recharge.
In the process of cleaning| –| Automatically| | •When the battery is low during cleaning, , the sweeping and mopping robot will automatically recharge.
•when the cleaning is finished, the sweeping and mopping robot will automatically recharge.
Tip: During charging, the sweeping and mopping robot cannot be turned off.
Add water to the water tank or clean the mop cloth mid way| | Short press the button| | •Pause the sweeping and mopping robot,
•Removes the floor mopping module, add water or clean the mop cloth, replace the floor mopping module
•Short- press the button again to continue cleaning
Set the Cleaning Mode| –| | | •The machine is in the standard mode by default.
•After it is connected with APP, you can select more modes in the App.
Failure State| –| | When the sweeping and mopping robot is abnormal, it will give a voice prompt and the power indicator will blink in orange.| •Please refer to “Troubleshooting” for solutions When the sweeping and mopping robot is abnormal
•When there is no operation for 60 minutes under the failure state, the sweeping and mopping robot will hibernate automatically.

Part-7 Maintenance

Replace the Dust Bag
When the dust bag s full, the ‘FULL UP” sign is keeping high brightness, and app notice is given. Please replace the dust bagin time. The ‘COLLECTING’ sign will be high brightness while the collector is working, When the host s fully charged, the mark of ‘BATTERY s all green and high brightness, battery power is less than or equal to 50%, just a half mark is high britghtness. Clean the Dust Passage
If the ‘FULLUP” sign The ‘COLLECTING’ sign and the ‘BATTERY” sign allis twinkling after the dust bag is replaced, it is recomme- nded to pull out the power plug and reverse the dust collection charging pile to check whether there are foreign maaters block- ing the dust passage.
If the dust passage s blocked, refer to the figure below and remove the transparent cover of the dust passage with a screwdriver to remove foreign matters.
Note: violent disassembly is prohibited After cleaning, replace the cover as it is. Clean the Infrared Lens/Charging and Dust Collection Sensor Head
Wipe them gently with a clean, soft, dry cloth. It is recommended to clean them once a month. Clean the Flter Screen of the Fan
The filter screen of the fan is below the dust bag. If there is dust accumulation, wipe it gently with a clean, soft, dry cloth, It is recommended to clean them once a month. Clean the Main Brush
The main brush is consumable and should be cleaned at least once a week. It is recommended to replace the main brush every 6-12 months to ensure the cleaning effect.

1. Reverse the sweeping and mopping robot, press the snap on the main brush cover, and remove the main brush cover and the main brush.
   Note: avoid hitting when reversing the robot to prevent damage to thelidar.

2. Cutoff the hair wound on the main brush with the cleaning knife,and then clean the main brush with the cleaning brush at the other end of the cleaning knife.

3. Replace the main brush and the main brush cover.
   Press and fasten the snap.

Clean/Replace the Side Brush

1. Remove the side brush with a screwdriver.
2. Replace the side brush after cleaning, or install a new side brush.

Tips : the side brush is consumable.It is recommendrd to replace it every 3-6 month to ensure the cleaning effect.
Clean the Sensors
It is recommended to use a clean, soft, dry cloth to wipe each sensor gently every week to ensure the normal use of the machine.
Sweeping and Mopping Robot:
Cliff sensor X4
Infrared sensor X3
Charging electrodetip X2
Wall-following position sensitive detector X 1 Dust Collection Charging Pile:
Infrared lens X2
Charging and dust collection sensor head X2 Battery Maintenance

• The sweeping and mopping robot has a built-in high- performance rechargeable lithium-ion battery pack.
  In order to maintain battery performance, please keep the battery pack charged every day.

• If the machine will not be used for a long time, please turn it off and store properly. Charge it at least every three months to avoid battery damage due to over discharge.

Clean the Two-in-one Water Tank

1. Press and hold the release button of the two-in-one water tank and at the same time pull it outwards.
2. Open the dust bin by pressing the dust bin snap.
3. Remove thefilter screen clip.
4. Take out the filter screen.
5. Remove the debris on the filter screen and screen clip with a cleaning brush.Tips: The filter screen is consumable. It is recommended to replace it every 3.6 weeks. Please make a purchase through the offcial channel,
6. Tum on the tap to clean the dust bin.
7. Open the water tank cover and inject an appropriate amount of water.
8. Please remove the water tank fittings from the machine according to the illustration and reverse it, remove the mop or replace it.

Tips:

1. If the mop is too dirty, it will affect the effect of mopping, please clean itin time
2. Be sure to remove the mop for cleaning and screw it dry before installation. It is forbidden to clean on the two in one water tank.
3. The mop is a consumable and it is recommended to replace it every 3-6 weeks.

Power failure restart
When the button is not responding or can not be turned off, reset the button with the pin length for one second, and the robot will restart the power.

Part-8 Troubleshooting

When there is any abnormality in the operation of the main engine, the power indicator will flash red. When some faults occur, the host will issue a voice prompt. Please refer to the table below to try to solve the problem.

2.The charging induction head is dirty
3.Bad contact of charging induction head| 1.Please confirm that the power cord of the dust collecting charging pile has been connected
2.Regularly clean the charging electrode head of the main engine and the dust collecting charging induction head of the dust collecting charging pile
3.Please eliminate the bad contact caused by the edge brush or other foreign bodies/dust/dirt, and you can try to manually replace the main engine
Recharge failed, dust collecting charging pile was not found| The dust collecting charging pile is sheltered or too far away| Please put the dust collecting charging pile in the open area;Please put the main machine near the dust collecting charging pile to try
Abnormal behavior| Abnormal program| Press the reset button to power off and restart
The vacuum made a strange noise while cleaning| Main brush/side brush or main wheel wound foreign body| Please clean the body of the vacuum after shutdown
Impairment of cleaning ability or ash drop| The dust bin is full or the filter screen is blocked or the main brush is entangled| Please clean the dust bin, the filter screen and the main brush in time
Unable to connect to APP| WIFI network abnormality or WIFI password error or APP abnormality| Please ensure that the main engine is in the area with good WIFI signal;Re-enter WIFI password or reset WIFI;Update the APP and try again
Excessive leakage of water from the mopping module/ water tank| The tank cover is not in place and the water output is adjusted to the maximum| Please confirm that the tank cover has been installed in place and adjust the appropriate amount of water in the APP.FiII the tank and let it stand to check whether there is any damage or leakage
During cleaning, the battery is low and the charge is returned but the sweep is not continued| The main engine is in Do Not Disturb mode or manually recharge| Please confirm in the APP that the main engine is not in Do Not Disturb mode, and there will be no continuous scanning in this mode.Manually charge back or manually put the main engine back to the dust collecting charging pile, the machine will not continue to sweep
---|---|---
Unable to return to dust collecting charging pile after fixed point cleaning or moving position| The robot rearranges or is too far away from the charging pile| After fixed point cleaning or long-distance moving, the robot will regenerate the map. If the dust collecting charging pile is too far away, it may not be able to charge back automatically. Please manually put the host back to the dust collecting charging pile for charging
The mop module does not produce water or little water| The water tank is short of water or the mop is too dirty or the mop bracket is not installed in place| Please check whether there is water in the water tank;Please clean the mop;Please install the mop correctly according to the the instructions.Check whether the outlet
hole is blocked by foreign matter, pay attention to add clean water without impurities
Please check whether the radar is stuck| The laser radar is blocked or jammed| Remove the occlusion or move the main engine to an open area and restart
Please check the crash barrier| Collision sensor stuck| Clean up the foreign body around the crash barrier or remove the main engine
Wipe the cliff sensor and activate away from the danger area| The cliff sensor is triggered after starting the main engine| Wipe the cliff sensor and move to a flat and spacious place to start
Please check the main brush| Brush get stuck| Clean the main brush, or remove the main engine
Please check the side brush| Side brush get stuck| Clean the side brush, or remove the main engine
Please check the main wheel| Main wheel get stuck| Clean the main wheel, or remove the main engine
Two in one tank removed| The two-in-one tank was taken out| Please install the two-in-one water tank and strainer, and confirm that the strainer and two-in- one water tank are installed in place
Low battery, start recharging| Low power during cleaning| Power is low, please charge it before use
Abnormal sounds coming from thefan| Fan abnormal| Please try turning off the machine and restarting it
---|---|---
Please wipe the TOF detector along the right wall| TOF detector anomalies along the wall| Please wipe clean the TOF detector along the wall
‘The radar cap is not moving.| The radar cap s stuck| The radaris pinned or stuck, please move to another area
and start again Radar protection:Do not allow children, pets or other heavy objects to stand on the sweeper to avoid radar damage caused by squeezing the radar cover, Man-caused damage is not covered by the warranty
Damaged or uninstalled batteries| Abnormal battery during charging| Ifthe battery temperature is too high or too low, please
wait unti the battery temperature is normal before using
Unable to start up| Low battery power or abnormal ambient
temperature| The battery s low, please charge it before use;The ambient
temperatureis too low (below 0°) or too high (above 50°),
please use in 0°~40°c environment

In case of abnormat operation of the dust collection charging pile, APP will give a message on the phone.

Overheat protection or failure of fan
starting| Please install the dust bag correctly;Try
dust collection
again after 30 minutesf it cannot be solved, please
contact customer service
Dust bag s full or blocked| Dust bagis fullor blocked| Change the dust bag, and timely clean the dust collection
charging ple (dust suction port, dust passage, fan filter
screen, etc)

Part-9 Warranty Instructions

The warranty period

1. Within 30 days from the day after delivery of the product,if the product has performance failure, you can enjoy free replacement or maintenance service after testing;
2. Within 31 to 90 days from the day after delivery of the product, if the product has performance failure, you can enjoy free replacement or maintenance service after testing;
3. Within 2 year from the day after delivery of the product, if the product has performance failure, you can enjoy free maintenance service.

Non-warranty regulation

1. Unauthorized maintenance, misuse, collision, negligence, abuse, liquid injection, accident, alteration, incorrect use of non-product accessories, or tear, alter labels, anti-counterfeiting marks;
2. Exceeded the validity period of three packages;
3. Damage caused by excessive force;
4. Not conforming to performance failure;
5. The performance failure of the product is caused by personal reasons.

The content of the warranty

Note: The main brush, side brush, main brush cover, filter screen, mop bracket, cleaning knife, disposable mop and disposable dust bag are the products of random consumables, no warranty period.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>