LUTRON DVRF-6L Diva Smart Dimmer User Guide
- June 3, 2024
- Lutron
Table of Contents
Quick-start guide
In-wall dimmer
DVRF-6L Diva Smart Dimmer
P/N 0302045 REV A
Diva Smart Dimmer
DVRF-6L
120 V~ 50/60 Hz
Installation videos can be found here:
www.casetawireless.com/support
Double your warranty
Love Caséta Wireless products?
Have ideas for making them better? Tell us what you think and we’ll extend
your warranty by 1 year.
www.casetawireless.com/register
Contents supplied
In-wall dimmer
(DVRF-6L)
| Wire connectors (5)|
Screws (2)
---|---|---
| |
Tools you’ll need
Flat-head screwdriver
|
Phillips-head screwdriver
---|---
|
Installing your dimmer
Installation for lights with one wall switch (single pole)
1. Turn power off at circuit breaker!
WARNING: SHOCK HAZARD
May result in serious injury or death. Turn off power at circuit breaker or
fuse before installing.
Important note:
We’ve included instructions for when a single switch is controlling the
lights. For installation instructions when two or more switches are
controlling a light, please visit
www.casetawireless.com/3way for
complete installation instructions and how-to videos.
2. Remove existing switch from wall
Remove the wallplate from switch.
Remove the switch and pull it away from the wall.
Disconnect all three wires* from the switch.
- If your switch has more than 3 wires attached, see “Installing Caséta Wireless in a 3-way switch application” video at www.casetawireless.com/3way
3. Ganging and Derating
Double Gang
|
Triple Gang
---|---
| 
Important note:
Multi-gang installations may reduce the dimmer’s maximum wattage rating. See
the chart below for maximum wattage information.
*Maximum wattage derating chart
(120 V~ 50/60 Hz)**
| Load Type | Single gang | Double gang | Triple gang |
|---|---|---|---|
| LED & CFL | 150 W | 150 W | 150 W |
**or***
| Incandescent & Halogen | 600 W | 500 W | 400 W |
|---|
- For maximum wattage information when mixing light bulb types see www.casetawireless.com/ganging
4. Connect the dimmer
- Connect the bare copper (or green) “ground” wire from the wallbox to the green wire on the dimmer using one of the large supplied wire connectors.
- Connect either of the remaining wires from the wallbox to the black wire on the dimmer using one of the large supplied wire connectors.
- Connect the remaining wire from the wallbox to the red wire on the dimmer using one of the large supplied wire connectors.
- Cap the blue wire coming from the dimmer with the small supplied wire connector. The blue wire is not used for single pole installations.
Note: Wire colors depicted in this install guide may not match what is in
your walls.
5. Mount the dimmer
Use the screws provided.
6. Attach the wallplate
Attach the adapter to the dimmer using the screws provided and snap on the
wallplate.
7. Turn power on at circuit breaker
To use your Caséta Wireless system
With a smartphone or tablet (Smart Hub required, sold separately)
The Caséta Wireless Diva Smart Dimmer can be controlled from a smartphone when
used with the Lutron Smart Hub (Smart Bridge) and the Lutron app.
If you are using the dimmer and remote control with the Lutron Smart Hub
follow the instructions below.
Note: If you are using the dimmer and remote control with another
manufacturer’s bridge, please refer to that manufacturer’s instructions for
set-up.
1 Press and hold “off” butto
2. Launch the Lutron app
3. Use the Lutron app to complete ALL remaining steps
| Add
devices
• Pico remotes
• Dimmers
• Shades
---|---
| Control three ways
|
Schedule your lights
| Connect
while away
Without a smartphone or tablet (Smart hub not required)
Pairing the dimmer and Pico remote control
1. Press and hold “off” button on dimmer
2. Press and hold “off” button on remote
Changing the favorite light level on the Pico remote control
(sold separately)
3. Set desired light level on dimmer
4. Press and hold “favorite” button on remote
For advanced features, tips for using Caséta Wireless dimmers with LEDs and
CFLs, the complete Caséta Wireless product line, and more, please visit
www.casetawireless.com/features
Using your controls
Replacing light bulbs using FASS
Pull the FASS switch out on the in-wall dimmer to remove power at the light
socket.
Important notes:
- For indoor use only.
- Operate between 32 ˚F (0 ˚C) and 104 ˚F (40 ˚C).
CAUTION
Use only with permanently installed fixtures with dimmable LED, dimmable CFL,
halogen, or incandescent,lamps. To avoid overheating and possible damage to
other equipment, do not use to control receptacles, motor-driven appliances,
or transformer-supplied appliances.
Codes
Install in accordance with all national and local electrical codes.
Grounding
When no “grounding means” exist in wallbox, the National Electrical Code
(NEC®) allows a control to be installed as a replacement if 1) a nonmetallic,
noncombustible faceplate is used with nonmetallic attachment screws or 2) the
circuit is protected by a ground fault circuit interrupter (GFCI). When
installing a control according to these methods, cap or remove green wire
before screwing control into wallbox.
FCC/IC Information
This device complies with part 15 of the FCC Rules and Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device
must accept any interference, including interference that may cause undesired
operation. Modifications not expressly approved by Lutron Electronics Co.,
Inc. could void the user’s authority to operate this equipment. Note: This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warranty
For warranty information, please visit
www.casetawireless.com/warranty
Troubleshooting
| Symptoms | Probable cause and action |
|---|---|
| Light does not turn on or in-wall dimmer light bar does not light up. | • Light |
bulb(s) burned out.
• Breaker is OFF or tripped.
• Light not properly installed.
• Wiring error.
• FASS switch on the dimmer is in the Off position.
Light does not respond to Pico remote control.| • The dimmer failed to pair
with Pico remote control; see Pairing
the dimmer and Pico remote control.
• The dimmer is already at the light level the Pico remote control is sending.
• The Pico remote control is outside the 30 ft (9 m) operating range.
• The Pico remote control battery is low.
• The Pico remote control battery is installed incorrectly.
• Bulbs turn off while being dimmed.
• Bulbs turn on at high light level but do not turn on at a low light level.
• Bulbs flicker or flash when dimmed to a low light level.| Verify bulbs are
marked dimmable and visit
www.casetawireless.com/lowend for
information on adjusting the dimmer for best bulb performance.
Go to
www.casetawireless.com/support
for additional troubleshooting suggestions.
Lutron, the Lutron logo, Diva, FASS, Caséta, Pico, and the design of the Pico
remote are trademarks or registered trademarks of Lutron Electronics Co., Inc.
in the US and/or other countries. Apple is a trademark of Apple Inc.,
registered in the U.S. and other countries. App Store is a service mark of
Apple Inc. All other product names, logos, and brands are property of their
respective owners.
© 2022 Lutron Electronics Co., Inc.
Works with energy efficient dimmable light bulbs:
| LED—up to 150 W
---|---
| CFL—up to 150 W
| Halogen—up to 600 W
| Incandescent—up to 600 W
NOTE: You can mix and match dimmable LED and CFLs, as well as halogen and
incandescent light bulbs, with Caséta Wireless dimmers.
Dimmable LED and CFL light bulbs vary in their dimming performance. If you’re
using these bulbs and they flicker or turn off, please visit
www.casetawireless.com/lowend for
information on adjusting the dimmer for best bulb performance.
For a complete list of compatible dimmable LEDs and CFLs, please visit
www.casetawireless.com/bulblist
Lutron Electronics Co., Inc.
7200 Suter Road
Coopersburg, PA 18036-1299, U.S.A.
Documents / Resources
|
LUTRON DVRF-6L Diva Smart
Dimmer
[pdf] User Guide
DVRF-6L, Diva Smart Dimmer, DVRF-6L Diva Smart Dimmer
---|---
|
LUTRON DVRF-6L Diva Smart
Dimmer
[pdf] User Guide
DVRF-6L Diva Smart Dimmer, DVRF-6L, Diva Smart Dimmer, Smart Dimmer, Dimmer
References
- casetawireless.com/lowend
- Caseta by Lutron | Smart Light Switches, Controls & Dimmers
- Installing Caséta for a light with two switches | Lutron
- Lutron Support Center | Lutron
- Application Notes | Caséta Wireless | Lutron
- Capacity Derating Charts
- casetawireless.com/register
- Application Notes | Caséta Wireless | Lutron
- casetawireless.com/warranty
- How to Factory Default Caseta Dimmers, Switches, and Fan Controls | Lutron
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>